MecPower Tecway Mini Kiddie Pirate User manual

Mini Kiddie Pirate
Manual
To avoid innormal operate, please read this operation manual before install.
Please keep this manual for read.

Safety Attentions
1) Certain part of the game is with high voltage. Adjust the game by
technician. Do not open the game door unless maintenance or parts
replacement is required.
2) Please switch off the power before checking and maintenance.
3) Please switch off the power before opening the game door.
4) Fire extinguisher equipment must be nearby the games.
Installation
The game must be located properly to avoid damages.
Improper Locations:
Plac e direc t ly
ex pos ed t o suns hine
Humid area Plac e w ith high
temperature
Plac e w ith c orross iv e
air and liguid
R ough area or plac e
w ith s trong s hak e
Plac e w it h mass iv e
dust

Notes of Usage
1) The voltage range of the game should be 105V ~ 115V/215V ~ 225V.
The proper voltage should be 110V/220V. The specific voltage accords
to the date plate on the back door of the game.
2) The plug must be plugged tightly but keep the power cords not be too
tight.
3) Please properly adjust the coin mech and the game settings when use
at the first time.
4) Please regularly check all the functions of the game when operate.
Notes of Maintenance
1) Be sure to check and maintance the game regularly.
2) Switch off the power before replacing the parts of the game.
3) The parts for replacement should be the same model as the old one.
4) Please check the connection and voltage output after replacing the
power supply.
5) The voltage of the PCB should be 5.1V ~ 5.4V.
6) Check whether the game has creepage and the voltage before
repairing the PCB

Notes of Clean
1) Please use clean and soft cloth to clean the game.
2) Prevent damaging the surface of the game, please do not use the
following cleanser:
 Alterative Cleanser;
 Acidic Cleanser;
 Insecticide, sterilized water, alcohol or other chemical cleanser.
Notes of Moving and Shipping
1) Properly disassemble the game for necessary moving and shipping.
2) Prevent the game from hitting or being attrite during movement.
3) Protecting the case when move the game.

TECHNICAL PARAMETER
Voltage: AC220V/110V（50/60HZ）
Max. current: 0.7A/1.4A
(Note: The proper voltage and current used accords to the nameplate at the back door
Max. power: 120W
Power (standby mode): 50W
Coin size: φ21mm ~ φ30mm (diameter)
1.2mm ~ 2.5mm (thickness)
Capacity of coin box: about 2900 pcs with coin size φ25mm*1.5mm
Location required: indoor use; temperature: -5~40°C ; RH > 90%; no contact with any
corrosive, greasiness and dirt.
Dimensions: L1420mm*720mm*H1370mm
1370
1420
720

Parts & Accessories
# DRAWING NAME MODEL/SPEC. QTY
1 LED light red, green, blue,
yellow 8
2 key 1285＃2
3 key 1396＃2
4 power cord 1
5 manual 1
OPERATION MANUAL

CHECK THE CONNECTION
1. Check if the inner structure of the game is loose caused by transportation or the terminals
drop.
2. Check if the game is grounded.
3. Check if the resistance of the GNDs is more than 100 megohm.
4. Adjust the coin mech before operation.
5. Connect the power cord.
Attentions:
a) Please make sure the power cord is not pressed by wheel, foundation, etc. Otherwise,
the wire will be damaged to cause short circuit, even fire. Do not use strong power to
extend and wring the wires. Do not make the wire be near to the high temperature
object. Properly put the wire to avoid any kicking or treading.
b) Hold the plug to pull it out from the socket.
c) Do not touch the plug with wet hands.
AAAA

d) Make sure the voltage and fuse used are proper.
Connect the power:
1. Confirm the value of voltage input is same as the one stated on the nameplate on the back
of the game.
2. Swith on the power switch.
3. Properly adjusted the coin mech and confirm it can work properly.
4. Check and confirm all the flash lights and monitor can work properly.
5. Enter into the setting menu to adjust the game setting (adjust the no. of game per game,
game time, etc…)
6. Test the game and confirm it can work properly.
7. Check and confirm the sound is ok.
CHECK BEFORE OPERATION
1. Confirm the power cord is properly plugged and without any damages.
2. Confirm the game is properly fixed.
3. Confirm the cabinet of game is without damages and burrs.
4. Confirm the surface of game is clean and with proper marks.
DAILY OPERATION
Please properly refer to the instructions above to check the game before operation.
After operation, please collect the coins and keep record of the coin meter.
！w a rn in g
B e fore inpu ting th e p ow e r, p lea se c h e ck the re s ista nce b e tw e e n inp ut po rt a n d G N D . M a ke
su re th e co nn e ction is prope r.

GAME SETTING
KEYS FOR SETTING
TEST: Enter into the setting menu or skip to the next menu.
ENTER: Change the setting.
SERVE: Free to play.
SW1
TEST
SERVE
SELECT
ENTER
ERASE
Setting
Free to play
Change
设置板
SETTING
BOARD

SETTING METHOD
Setting method: press “TEST” to enter into the game setting menu → press the “TEST” to
choose the setting item →press “ENTER” to change the setting → press “ENTER” exit
setting.
SETTING DESCRIPTION
1) Game setting interface：
Descriptions:
Language: This setting decides which language will be displayed in screen, Chinese or
English.
COIN：this setting can decide how many coins player should insert for one game. if setting to
“2”,it means insert 2 coins for 1 game.
VOLUME：this setting can decide the volume and “1” stands for the lowest. (Note: the volume
can be adjusted by adjusting the volume potentiometer on the amplifier board.).
TIME：this setting decides the limit time for one game. if setting to “2：00”， it means has 3
minus for one game.
DEMO MUSIC：DEMO MUSIC：this setting decides if play the demo music, if set to “ON”, then
the game will play demo music when standby
English
5
2:00
Exit
TIME
POTENTIOMETER
TESTING
VOLUME
COIN
GAME SET AND TEST
LANGUAGE
1
DEMO MUSIC ON

POTENTIOMETER TESTING：This setting is to test whether the encoder is working normally.
When the steering wheel is turning, the number will change.
EXIT：Press“ENTER”to exit setting
2) Steering wheel Test
Descriptions:
When the steering wheel is turning, the cursor will move in the horizontal direction.
Press TEST Key to Exit
POTENTIOMETER TESTING
( 301, 277 )

ADJUSTMENT
Adjust the coin mech:
Descriptions:
A. remove the plastic coin from the coin sample chute and put a proper coin in it.
B. remove the screws on the back of coin entrance. Adjust the the fix chip of back of coin
entrance according to the diameter of coin you will use so that it will prevent the large coin
blocking the coin mech.
C. set the COIN SW to “ON”.
D. set the pulse of COIN signal to “50MS”.
E. following the drawing to adjust the resistance for sensitivity of coin acceptance, turn
colckwise for increasing and counterclockwise for decreasing.
adjusting chip of entrance
coin reject bar
COIN signal wavelength
adjusting SW
COIN signal SW
power/signal input
micro-adjust resistance
sample coin chute
DC+ 12V
STR ICT SLACK
Sensitivity
+-
COIN
Remove
REPLACE
Backward
SW3
100ms SLOW
25ms FAST
NOM
normal
MGN
accurate
50ms MEDIUM
WHITE
COUNTER(+/-)
GROUND
N.C.
SW1
SW2
N.O.
COUNTER(-/+)
COIN SIGNAL
GRAY
BLACK
RED
GRAY

Adjust the main board:
Descriptions:
Reset button: press this button to clear the data of coin saved in main board and reset the
game settings to default settings.
Volume potentiometer: twist this potentiometer with screw driver. Twist clockwisely to increase
the volume, counterclockwisely to decrease the volume.
Battery: this battery have memory function that will provide power to save the data of
coin and game settings in main board when the power is cut off. If the data can not be
save when the power is cut off, please replace the battery.

CHECK AND MAINTENANCE
Daily check
ITEM DESCRIPTIONS
Coin mech Check if the coin mech can work properly.
Encoder Check if the encoder can control the direction.
Sound Check if the volume is proper.
Display Check if the display can work properly.
Temperature, humidity Check if the temperature and humidity is proper.
Daily maintenance:
ITEM DESCRIPTIONS
Cabinet Clean the cabinet with water and cleaning paper.
Monitor Acrylic Clean the acrylic with water and cleaning paper.
PCB Clean the PCB with small brush.

TROUBLESHOOTING
PROBLEM CAUSES SOLUTIONS
No sample coin. Insert sample coin into the coin mech.
Sensitivity for coin getting through the coin
mech was setting too high. Adjust the coin mech.
Coin mech is bad. Replace the coin mech.
Bad connection of the lights. Re-connect the wires of the lights.
Light is bad. Replace the light.
Drive board for the light is bad. Repair or replace the drive board.
Bad connection of the motor. Re-connect the wires of the motor.
Capacitor for motor is bad Replace the Capacitor.
Motor is bad. Replace the motor.
Bad connection of the direction encoder. Re-connect the wires of encoder
Encoder is bad. Replace theencoder
The power cord for the monitor is loose. Re-connect the wires fo the monitor.
The VGA wire is not connected. Re-connect the VGA wire.
Monitor is bad. Repalce the monitor
Main board is bad. Replace the main board.
Wire of speaker is loose. Re-connect the wires of speaker.
Volume is too low. Increase the volume.
Speaker is bad. Replace the speaker.
No AC110V/220V voltage input. Check the connection and 110V/220V input
voltage.
The fuse is burnt. Replace the fuse.
No output voltage of power supply. Repair or replace the power supply.
The output voltage of power supply is too
low. Adjust the ouput voltage of power supply to 5.2V.
The main board is bad. Replace the main board.
Direction control has
problem.
No Display.
No Sound.
No movement.
Can't insert coin.
Chasing lights do not
light up.
The motor does not
work.

PARTS LIST
Cabinet:
16
15
21
22
23
14
24
20 19
18 17
13
12
11
10
09
08
07
06
05
04
03
02
01

Steering wheel:
06
12
13
14
11
10
09
08
07
05
04
03
02
01

PCB assembly:
08
07
05
06
04
03
02
01

Chassis:
01
02
03
04
05
06
07 08
09

SCHEMATIC DIAGRAM
encoder sw signal line 1
Grey/W2
Pi1
Br3-1
B3-1
R1
Bla1
O1
R/W1
Y/G1
Grey/W1
Pu/W1
B/W1
Br/W1
W/Bla1
Pu1
B1
G1
Y1
Br1
G/Bla1
Grey/W2
R1-2
+
4"
speaker
15W
-
Bla1-1
+
-
+12V
+12V
right chasing light
left chasing light
3-color chasing light
33
2 2
11
4 4
1 1
44
22
3 3
GND
11
+12V
2 2
solid relay
motor
M
Bla3
Bla2
G/Bla1
R/W1
Y/G1
Grey/W1
Pu/W1
B/W1
Pi1
G2
Y2
Br/W1
W/Bla1
Pu1
B1
G1
Y1
Br1
shooting sw
encoder sw
11
2 2
33
O4
small chasing light 2
small chasing light 3
small chasing light 1
speaker light 2
service button
motor
small chasing light 3
small chasing light 2
small chasing light 1
big light 3
big light 2
circuit breaker
power input
speaker light 1-2
coin meter
coin sw
encoder sw signal line 2
big light 1
Bla5
O5
R1
33
2 2
11
4 4
55
6 6
Bla4
Bla1-1 R1-1 O1-1
O1-1 R1-1 Bla1-1
33
2 2
11
to main board CON6
F G IH
EBCDA
VGA connector
CON4
+12V
+5V
GND
IO board
CON3
LCD
E
B
C
D
A
F
L
G
J
I
H
K
R
M
P
O
N
Q
X
S
V
U
T
W
Y
Z
35
32
33
34
31
36
29
26
27
28
25
30
23
20
21
22
19
24
17
14
15
16
13
18
11
8
9
10
7
12
6
1
4
3
2
5
H1
I1
J1
G1
F1
A1
D1
C1
B1
E1
5
2
3
4
1
6
7
10
9
8H
I
J
G
F
A
D
C
B
E
set sw
GND
+5V
+12V
power
supply
220V
220V
12V
GND
293961
E
O1-O5
Bla1-Bla5
290378
SELECT
SERVE
SW1
TEST
ENTER
setting board
88
6 6
7 7
5
2
3
4
1 1
4
3
2
5
5V
coin mech
3 3
22
1 1
change sw
shooting button
speaker light 1
44
big light 1
coin meter
B3-1
Br3-1
O2
O3