Mediclinics GAJ002AC User manual

Installation
Automatic Faucet with soap dispenser
Read ALL the instructions completely before
installation
Ref.: TBD / Rev. A 18/09/2019

Model No.
Description
Power Suplly
Static Power Consumption
Sensing Range
GAJ002AC
Automatic faucet with soap dispenser
DC:6V(4AA alkaline batteries）
AC：220V-240V；50/60Hz
DC:≤0.18-0.33mW
Sensing for water：25±5CM
(based on white board)
Sensing for soap：10±2CM
(based on white board)
Water Pressure
Ambient Temperature
Inlet
0.5Bar-8 Bar
1℃-55℃
G1/2”
Trouble shooting
Specifications
Symptom Cause
The battery is exhausted
Water supply cut off
No water out Dirt in the filter
Water pressure too low
There is still air in the soap tube
No soap out
Treatment
Change the battery
Check supply
Clean the filter
Raise the pressure
Sense the soap sensor
repeatedly until soap out
Toolow ambient temperature, Fill in proper amount of warm
the soap is easy to freeze water (approximate 60℃)
The soap in the bottle istoo little Fill more soap
The check valve is blocked Replace the check valve
Water or soap
will not turn off
Dirt on the sensor window
Clean the sensor
Water supply is turned down Adjust water supply
Too little
water flow The filter is too dirty clean the filter
Water pressure is too low Raise the pressure
Toomuch
water flow
Short cycles
of battery
Water pressure is too high
Adjust pressure
Incorrect batteries
The light is broken
Change to 4AA
Alkaline batteries
Change the light or
circuit board
The indicator
light is
The circuit board is wet or signal
line is wet
The battery is exhausted
Poor connection of battery
Dry out
Change the battery
Check battery connections

The firs gear The second gear
WALL
The third gear The fourth gear
1、Fill the bottle full of liquid soap for the first time；
2、Press and hold the dispense button on the control box, release till
the soap is dispensed.
3、Start the system by passing your hand in the sensor range, soap
will dispense automatically.
Note: It has four soap dispense volume adjustment:
1. Low volume
2. Normal volume
3. Medium volume
4. High volume
Viscosity of liquid soap:100-3500cp(mpA.s)
Recommended Usage
Domestic
Heavy Commercial
Light Commercial
Health Care
Part name
Debugging step for soap dispenser
Aerator
Soap nozzle
Water sensing
Soap sensing
Faucet body
Basin
Nut
M26*1.5mm
Transformer
Rotary union
Pipe buckle
OUT
Control box IN
Pump
Bottle
Inlet
wall
Battery case
bracket
94mm
Battery
wall
bracket
30mm
Bottle
Floor
Max.40mm
Recommended 300mm
Min 350mm
Recommened 360mm
76mm

Installation
Warning :Before installing the new spout it is essential that you throughly flush
through the pipework in order to remove any remaining swarf,solder etc.
Failure to carry out this procedure could cause problems or damage to the
workings of the spout.
This product must not be modified in any way as this will invalidate the guarantee .
OUT
IN
1. Screw off the rotary union,nut
and gasket from the faucet.
3. Fit wall bracket
Position the brackets onto the wall
and mark the position of the fixing holes.
Remove the brackets and drill suitable
holes for the wall plugs supplied .
Fit the wall plugs and brackets.
2. Fit the spout to the basin ensuring
the cables and hose are threaded
through the hole in the basin.
4. Attach the pump to bottle
Ensure the dispenser tube is located
inside the bottle and push the pump
the pump down firmly onto the bottle
until a loud “click” is heard .
Connect the dispensing cable from the
spout into the top connection on the pump.
Place pump into bracket .
5.Position and fix the control box
onto the wall surface .
7. Insert Batteries.
Remove the battery cover and insert
4AA battery case ensuring they are
inserted the correct way .Replace the
battery box cover and tighten thescrew.
Push the holder into the battery case
wall bracket.
6. Connect the hose with the rotary
union to the outlet of the control box.
8. Insert the case into the holder .
Push the holder into the battery
case wall bracket.
Installation
OUT
IN