Microh Ultra Sport 1200 User manual

.1.
INTRODUCTION
This equipment is produced in accordance with CE standards and conforms to the
international standard DMX512 protocol.
On receiving this product, please carefully check that there has been no damage caused in
transportation and that the following parts are enclosed:
1 1200W SPOTMOVING HEAD
1 SIGNAL CABLE
1 USER MANUAL
1 SAFETY CABLE
2 CLAMPS
IMPORTANT
BEFORE OPERATION PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE REAR
PANELOF THIS UNIT IS THE SAME AS THE SUPPLIED MAINS POWER IN YOURAREA.
READ THIS USER MANUALCAREFULLYBEFORE OPERATION
SAFETY WARNING
ØThis product must be installed by a qualified professional
ØAll operation and maintenance must be carried out in accordance with this user manual.
ØKeep this device away from any form of water or moisture at all times.
ØAlways disconnect the power before attempting to open the equipment housing or carrying
out any maintenance.
ØAvoid looking directly into the light source (especially those who suffer from epileptic fits)
ØDO NOT touch the equipment casing during operation due to high temperatures of the metal
and plastic housing.
ØThis equipment is designed for indoor use only.
ATTENTION
ØThis product left our premises in perfect condition. In order for safe operation and to
maintain the original condition, the user must always follow the instructions and safety
warnings described in this user manual.
ØThe manufacturer cannot accept liability for any resulting damages caused by non-
observance of this manual or any unauthorized modifications to the equipment and are not
subject to warranty.
ØAlways make sure that the equipment is OFF before connecting the power cables.
ØAlways make sure that the power cable is never cut or damaged by sharp edges. It is
advisable to check the state of the power cable from time to time.
ØDO NOT connect this equipment to a dimmer rack.
ØThis device falls under Protection Class I. Therefore it is essential that the yellow/green
wire must be earthed.
ØIf during transportation or storage the equipment has gone through drastic temperature
changes, it is advisable to allow some time for the equipment to first adjust to room
temperature before operation.
ØNever turn on the equipment without a lamp
ØAvoid shaking of strong impacts to the equipment.

ØNever lift the equipment by holding it at the head or arms. Always use the handles on the
base.
ØDO NOT turn on the lamp at short intervals as this will reduce the lamp's life.
ØThe maximum ambient temperature of the housing is ta=45 . If the temperature is in
excess of this the thermal switch will shut off the power.
ØWhen transferring the product, it is advisable to use the original packaging that the unit left
the factory in.
REAR PANEL OF THE BASE
The head must be locked for transportation-the tilt lock button is pushed and the pan
lock/unlock lever is in lock position. To unlock the head, press the tilt unlock button and move
the pan lock/unlock lever to unlock position.
DESCRIPTION
5 Pin DMX output
5 Pin DMXinput
Live fuse holder
Power switch
Power cord
Moving head
Tilt lock button
Pan lock button
Handel
.2.

Lamp chamber
Color wheel 2
Thermostat
Ignitor
Inside fresnel lens
Lamp cover
.3.

DIMENSIONS
.4.
489 mm
151 mm
585 mm
602 mm
525mm
506 mm

LAMP ADJUSTMENT
REPLACING LAMP
CAUTION: ALWAYS SWITCH OFF AND UNPLUG AT THE MAINS BEFORE INSTALLING
THE LAMP
1. Disconnect the power and all the unit to cool for at least 10 minutes.
2. Loosen screws indicated A& Bon the lamp cover at the back of the head.
3. Gently pull and remove the lamp cover and lamp holder from the head.
4. Holding the lamp by its ceramic base, carefully pull the lamp straight out of the lamp socket.
5. Holding the new lamp by its ceramic base, gently insert the lamp in to the lamp socket.
6. Reinsert the lamp cover and lamp holder and tighten screw A& B.
IMPORTANT:
ØAlways make sure that the lamp is installed tightly into the lamp socket.
ØDO NOT install a lamp other than that specified in this user manual.
ØDO NOT touch the glass area of the lamp with bare hands.
When this product left the factory, the lamp holder was calibrated here. However, due to the
possibility of small deviations between lamps, fine adjustments after replacement may
improve light output.
1. Turn on the lamp and operate with white beam (i.e. no effects)
2. Open the shutter and the iris with the dimmer intensity at 100%.
3. Focus the light beam on a flat surface (i.e. wall/floor)
4. Center the hot-spot (the brightest part of the image) using the 3 adjustment screws X, Y
& Z.
5. Once the hot-spot has been centered, remove the hot-spot and balance the light
output by turning the adjustment screws a quarter-turn clockwise one after another. If the
hot-spot cannot be located, adjust the lamp until the light output is evenly distributed.
6. If the light output is brighter around the edge than in the center or if the light output is too
low, the lamp is too far back from the reflector. Turn the screws X, Y& Za quarter-turn
anti-clockwise one after another until the light output is evenly distributed.
Disconnect the fixture from AC power before re-lamping.
Lamp is hot! Risk of fire! Protect hands and eyes.
Wait at least 15min. before opening
the covers and removing
lamp from the fixture.
Lamp
Lamp holder
Fixed the lampholder
of screw(A,B)
Adjust screw (X,Y,Z)
.5.
INSTALLATION

.6.

Omega-holde
Clamp
Secure chain
.7.
RIGGING THE FIXTURE
IMPORTANT: INSTALLATION MUST BE CARRIED OUT BY A QUALIFIED
PROFESSIONAL.
ØThe equipment must be mounted on equipment the has been designed and constructed in a
way that can withhold 10 times the weight for 1 hour without any structural damage to the
supporting structure.
ØThe installation must always be secured with a second safety attachment, e.g. safety cable.
This secondary safety attachment must be connected in a way that allows no part of the
equipment to fall to the ground if the main attachment fails.
ØWhen rigging, derigging or servicing the fixture, all persons must clear the area below the
work place.
ØThe user must have the safety and technical aspects of the installation checked by a qualified
professional before commencing operation.
ØThe user must have the equipment checked every four years by a qualified expert or in
accordance to local health and safety regulations.
ØThe user must have the installation checked by a qualified professional at least once a year.
ØThe equipment must be installed out of reach of people.
ØThe equipment must never be mounted swinging freely.
ØThis device can be placed directly on the stage floor or rigged in any orientation on a truss
without altering its operating characteristics.
Mounting using the Omega-Holder:
1)Bolt each clamp to the omega holder with a M12
bolt.
2)Attach the Omega-Holder to the bottom of the
base by inserting both screw bolts into the base
and tightening clockwise.
3)Connect the safety cable through the two holes
in the bottom of the base and to the truss.

The fixture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output. The
sockets are wired in parallel.
DMX-OUTPUT DMX-input
1- Ground
2 - Signal (-)
3 - Signal (+)
4 - Free
5 - Free
Occupation of the XLR-connection:
XLR mounting-socket: XLR mounting-plug:
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120 resistor between Signal (-) and Signal (+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
The transform of the controller line of 3 pins and 5 pins (plug and socket)
DMX-512 connection/connection between fixtures
120
Possible omega holder 4 positions:
5
.8.

001
Current DMX address
MODE
Press UP/DOWN key to selectYES
(inver direction)/NO(normal direction)t
Press UP/DOWN key to selectYES
(inver direction)/NO(normal direction)t
Press UP/DOWN key to select
DMX address(000-489 )
Press enter for complete
reset of equipment
MODE
MODE
Press ENTER to
display software
version
MODE
MODE
MODE
MODE
Press UP/DOWN to turn backlight on/off
DMX ADDRESS
PAN REVERSE
TILT REVERSE
RESET
LAMP
BACKLIGHT
SOFTWARE VERSION
RUN MODE ENTER DMX
MANUAL
PAN
TILT
SHUTTER
DIMMER
FOCUS
ZOOM
ENTER
UP/DOWM
UP/DOWN
UP/DOWN
UP/DOWN
UP/DOWN
UP/DOWN
Press UP/DOWN to turn lamp on/off
Press ENTER to display the current PAN
movement range. Press UP/DOWN key to adjust
the PAN(0 ~54 ) movement range.0
Press ENTER to display the current TILT
movement range. Press UP/DOWN key to adjust
the TILT(0 ~280 ) movement range.
Press ENTER to display the current SHUTTER
setting. Press UP/DOWN key to adjust the
SHUTTER setting
Press ENTER to display the current DIMMER
setting. Press UP/DOWN key to adjust the
DIMMER setting
Press ENTER to display the current FOCUS
setting. Press UP/DOWN key to adjust the
FOCUS setting
Press ENTER to display the current ZOOM
setting. Press UP/DOWN keyto adjust the ZOOM
setting
CONTROL PANEL
MODE
.9.