MrCool Signature Series Quick start guide

The Signature Series is NOT designed for amateur installation. Installation SHOULD be performed by an authorized technician.
Please read this manual carefully before installation and keep it for future reference.
The Signature Series is NOT designed for amateur installation. Installation SHOULD be performed by an authorized technician.
Please read this manual carefully before installation and keep it for future reference.
Owner & Installation
Manual
MGD*95SE*XA Gas Furnace
Signature Series
All manuals and user guides at all-guides.com

507277-03C Page 1 of 53mrcool.com
INSTALLATION INSTRUCTIONS
MGD*95SE*XA
Warm Air Gas Furnace
Save these instructions for future reference
(P) 507277-03C
*P507277-03C*
Manufactured By
MRCOOL,LLC
Hickory, KY 42051
This manual must be left with the homeowner for future reference.
WARNING
CAUTION
Table of Contents
Unit Dimensions 2
Parts Arrangement 3
Gas Furnace 4
4
Safety Information 4
6
6
9
12
Duct System 12
14
28
31
34
37
41
42
43
44
46
52
All manuals and user guides at all-guides.com

507277-03CPage 2 of 53 mrcool.com
EXHAUST AIR
OUTLET
COMBUSTION
AIR INTAKE
2 1/16 (52)
GAS PIPING INLET
(Either Side)
ELECTRICAL INLET
(Either Side)
Return Air
Opening
WEIVEDIS
TOP VIEW
27 3/4
19 1/4
(489)
91/8 (232) Right
6 9/16 (167) Left
2 (51)
Either Side
3/4
(19)
B
Supply
Air
9/16
(14)
9/16
(14)
9/16
(14)
19 7/16
(494)
CONDENSATE
TRAP CONNECTION
5
(127)
61/2 (165)
Either Side
2 1/4
(57)
(Either Side)
1 (25)
Front Panel (705)
AIR FLOW
33
(838)
C3/4
(19)
3/4
(19)
FRONT VIEW
Supply
Air
9/16
(14)
9
(229)
Unit Dimensions
Capacity A B C
in. mm in. mm in. mm
045-3
070-4 17-1/2 446 16-3/8 416 16 406
090-4
110-5 21 533 19-7/8 504 19-1/2 495
All manuals and user guides at all-guides.com

507277-03C Page 3 of 53mrcool.com
Figure 1.
CONTROLBOX
(Includesintegratedcontrol,
transformer and door switch)
BAG ASSEMBLY
BLOWERMOTOR
(hidden)
COMBUSTION
AIR INDUCER
BURNERBOX ASSEMBLY
(include sensor, rolloutswitchesandignitor)
GAS VALVE
BLOWERDECK
HEAT EXCHANGER
COLDENDHEADERBOX
PRIMARY LIMIT
BLOWER
ACCESS PANEL
HEATING
ACCESS PANEL
COMPARTMENT
COMPARTMENT
Parts Arrangement
All manuals and user guides at all-guides.com

507277-03CPage 4 of 53 mrcool.com
Gas Furnace
NOTE: In Direct Vent installations, combustion air is taken
Non-Direct Vent installations, combustion air is taken from
Figure 2.
Shipping and Packing List
1 - Wire tie
NOTE:
Safety Information
DANGER OF EXPLOSION!
DANGER
Building Codes
All manuals and user guides at all-guides.com

507277-03C Page 5 of 53mrcool.com
Locations and Clearances
NOTE:
NOTE:
Installed in Combination with a Cooling Coil
HEAT or COOL
Quincy, MA 02269
Heating Unit Installed Parallell to Air Handler Unit
AIR HANDLER
GAS UNIT
Dampers
(open duringcooling
operationonly)
Dampers
(openduringheating
operationonly)
Figure 3.
NOTE:
Use of Furnace as a Construction Heater
DO NOT USE THE UNIT FOR CONSTRUCTION HEAT
UNLESS ALL OF THE FOLLOWING CRITERIA ARE
MET:
All manuals and user guides at all-guides.com

507277-03CPage 6 of 53 mrcool.com
EQUIPMENT MAY EXPERIENCE PREMATURE
COMPONENT FAILURE AS A RESULT OF FAILURE TO
DISCLAIMS ALL LIABILITY IN CONNECTION WITH
NOTWITHSTANDING THE FOREGOING, INSTALLER
IS RESPONSIBLE FOR CONFIRMING THAT THE USE
OF CONSTRUCTION HEAT IS CONSISTENT WITH
THE POLICIES AND CODES OF ALL REGULATING
General
•
•
•
•
•
NOTE:
•
•
•
CAUTION
Combustion, Dilution & Ventilation Air
NOTE: In Non-Direct Vent Installations, combustion air is
All manuals and user guides at all-guides.com

507277-03C Page 7 of 53mrcool.com
•
•
•
•
•
•
•
•
•
•
•
•
•
WARNING
CAUTION
Air from Inside
All manuals and user guides at all-guides.com

507277-03CPage 8 of 53 mrcool.com
Figure 4.
Inside
OPENINGS
(To Adjacent
Space)
NOTE : Each opening shall have a free area of at least one square inch
per 1,000 Btu(645 mm2per.29 kW)per hour ofthetotal inputratingof
all equipmentin the enclosure,but not lessthan 100 squareinches
(64516 mm
2
ROOFTERMINATED
EXHAUSTPIPE
SIDEWALL
TERMINATED
EXHAUSTPIPE
(ALTERNATE
LOCATION)
FURNACE
).
Air from Outside
(Inlet Air from CrawlSpace and Outlet Air toVentilated Attic)
NOTE: Theinletand outlet air openings shall each have a free area
of at least one square inch per 4,000 Btu (645 mm
2per 1.17 kW)per
hour of the total inputrating of all equipment in the enclosure.
OUTLET
AIR
INLET
AIR
VENTILATION
LOUVERS
(Forunheated
crawl space)
FURNACE
ROOFTERMINATED
EXHAUSTPIPE
VENTILATIONLOUVERS
(Each end of attic)
SIDEWALL
TERMINATED
EXHAUSTPIPE
(ALTERNATE
LOCATION)
Figure 5.
Outside
Figure 6.
Outside
(All Air Through Ventilated Attic)
NOTE: Theinlet and outlet air openings shall each have a free area of
at least one square inch per 4,000 Btu (645 mm2per 1.17 kW) per hour
of the total input rating of all equipment in the enclosure.
OUTLET
AIR
VENTILATION LOUVERS
(Each end of attic)
INLETAIR
(Ends12"above
bottom)
ROOFTERMINATED
EXHAUSTPIPE
SIDEWALL
TERMINATED
EXHAUSTPIPE
(ALTERNATE
LOCATION)
FURNACE
Figure 7.
Outside
OUTLET AIR
INLETAIR
NOTE: Eachair duct opening shall have afree area of at least one
square inch per 2,000 Btu(645 mm2per .59 kW)perhour of the total
input rating of all equipment inthe enclosure. If the equipmentroom
is located against an outside wall and the air openings communi-
cate directly with the outdoors, each opening shall havea free area
of at least 1 square inch per4,000 Btu (645 mm2per 1.17 kW)per
hour of the total input rating of all other equipment in the enclosure.
ROOFTERMINATED
EXHAUSTPIPE
SIDEWALL
TERMINATED
EXHAUSTPIPE
(ALTERNATE
LOCATION)
FURNACE
All manuals and user guides at all-guides.com

507277-03C Page 9 of 53mrcool.com
Figure 8.
(Inlet Air from Ventilated Attic and Outlet Air to
Outside)
NOTE-The inlet and outlet air openings shall each have a free area
of atleast one squareinch per 4,000 Btu (645mm2per 1.17kW) per
hour of the total input rating of all equipment in the enclosure.
Ventilation Louvers
Inlet Air
(Minimum
12 in.(305mm) Above
attic floor)
Roof Terminated
Exhaust Pipe
Furnace
*Intake Debris
Screen
(Provided)
* See Maximum Vent Lengths table
Figure 9.
(Inlet Air from Ventilated Crawl Space and Outlet Air
to Outside)
NOTE-The inlet and outlet air openings shall each have a free area
of at least one square inch per 4,000 Btu (645mm2per 1.17kW)per
hour of the total input rating ofall equipment in the enclosure.
Roof Terminated
Exhaust Pipe
Furnace
Ventilation
Louvers
(Crawl space)
*Intake Debris Screen Provided)
Inlet Air
(Minimum
12 in.(305mm)
Above crawl
space floor)
Coupling or
3 in. to2 in.
Transition
(Field Provided)
* See Maximum Vent Lengths table
CAUTION
Installation
Setting Equipment
CAUTION
Shipping Bolt Removal
Figure 10.
NOTE:
WARNING
All manuals and user guides at all-guides.com

507277-03CPage 10 of 53 mrcool.com
Figure 11. Setting Equipment
FRONTVIEW SIDEVIEW
AIR FLOW AIR FLOW
1/2"
max.
AIR FLOW
SIDEVIEW
Unit must be level side−to−side. Unit maybe positioned
from level to 1/2"towardthe frontto aid in draining.
Figure 12.
WARNING
Top
Bottom
Left Side Right Side
Top 0
*Front 0
Back 0
Sides 0†
Vent 0
Floor NC‡
*Frontclearancein alcove installationmust be 24 in. (610 mm).
Maintain a minimumof 24in. (610mm) for frontserviceaccess.
†Allow proper clearances to accommodate condensate trap.
‡Thefurnacemay beinstalled on acombustiblewood oorif an optional
additive base is install
Figure 13.
Clearances
0
*Front 0
Back 0
Sides 0†
0
NC‡
See Figure 14
Table 1.
Cabinet Width Front to Rear Side to Side
in. mm in. mm
19-3/4 502 16-5/8 422
19-3/4 502 20-1/8 511
NOTE
All manuals and user guides at all-guides.com

507277-03C Page 11 of 53mrcool.com
Figure 14.
SUPPLY AIR
PLENUM
PROPERLY
SIZED FLOOR
OPENING
FURNACE
NON-COMBUSTIBLE
FLOORING
Installation on Combustible Flooring
See Figure 15
CAUTION
Table 2.
Cabinet
Width
Catalog
Number
Front to Rear Side to Side
in. mm in. mm
11M60 22 559 18-3/4 476
(21”) 11M61 22 559 22-3/4 578
Figure 15.
FURNACE
SUPPLY AIR
PLENUM
COMBUSTIBLE
FLOORING BASE
PROPERLY
SIZED FLOOR
OPENING
FLOORING
COMBUSTIBLE
NOTE:
Installation on Cooling Coil Cabinet
See Figure 16
NOTE:
Figure 16.
COOLING COIL
PLENUM
PROPERLY
SIZED FLOOR
OPENING
FURNACE
All manuals and user guides at all-guides.com

507277-03CPage 12 of 53 mrcool.com
Figure 17.
SECURE FROM
OUTSIDECABINET
PLENUM
(Field Provided)
SEALINGSTRIP
(Field Provided)
Side View
CABINET
SIDE PANEL
Figure 18.
SECUREFROM
INSIDECABINET
PLENUM
(Field Provided) SEALINGSTRIP
(Field Provided)
Side View
CABINET
SIDE PANEL
Filters
Table 3.
Furnace Cabinet Width
17-1/2”
21”
Duct System
NOTE:
Supply Air Plenum
Return Air Plenum
NOTE:
Table 4.
D1785
F891
D2466
F441
F438
D2241
F442
F628
D1527
D2468
D2661
D2665
PRIMER & SOLVENT CEMENT ASTM
SPECIFICATION
F656
D2564
F493
D2235
D2564, D2235,
F493
Cement D3138
CANADA PIPE & FITTING & SOLVENT
CEMENT MARKING
ULCS636
POLYPROPYLENE VENTING SYSTEM ULC-S636
ULC-S636
TM ULC-S636
All manuals and user guides at all-guides.com

507277-03C Page 13 of 53mrcool.com
CAUTION
IMPORTANT
Canadian Applications Only
Table 5. Outdoor Termination Kits Usage
Capacity
Vent Pipe
Dia.
(in.)
Standard Concentric
Outdoor Exhaust
Accelerator
(Dia. x Length)
Outdoor Exhaust
Accelerator
(Dia. x Length) Kit Concentric
Kit
Concentric
Kit
Concentric
Kit
51W11**
71M80
or
†44W92††
69M29
or
†44W92††
60L46
or
44W93†
045
2 YES YES YES
2-1/2 YES YES YES
3 YES YES YES
070
2 YES YES YES
2-1/2 YES YES YES
3 YES YES YES
090
2 YES YES YES YES
2-1/2 YES YES YES YES
3 YES YES YES YES
110
2 YES YES YES YES
2-1/2 YES YES YES YES
3 YES YES YES YES
All manuals and user guides at all-guides.com

507277-03CPage 14 of 53 mrcool.com
Joint Cementing Procedure
NOTE:
DANGER OF EXPLOSION!
DANGER
NOTE:
NOTE:
Venting Practices
Figure 19. Piping Suspension Guidelines
* SeeTable 4 forallowable pipe.
NOTE: Isolate piping atthe point where it exits the outside wall or
roof in order to prevent transmission of vibration to the structure.
SCHEDULE 40
PVC − 5’
all other pipe* − 3’
Wall edistuoedisni
24"maximum
3/4"minimum
Wall Thickness Guidelines
insulation
(if required)
Figure 20.
CHIMNEY
OR GAS
VENT
(Checksizing
for remaining
appliance)
FURNACE
(Removed from
from common
vent system)
WATER
HEATER
OPENINGS
(To Adjacent
Room)
REPLACING FURNACE THAT
WAS PART OF A COMMON
VENT SYSTEM
If this gas furnace replaces a furnace which was
commonly vented with another gas appliance,
the size of the existing vent pipe for that gas appliance
must be checked. Without the heat of the original
furnace flue products, the existing vent pipe is
probably oversized for the single water heater or
other appliance. The vent should be checked for
proper draw with the remaining appliance.
Exhaust Piping
See Figure 22
All manuals and user guides at all-guides.com

507277-03C Page 15 of 53mrcool.com
CAUTION
CAUTION
Vent Piping Guidelines
NOTE: In non-Direct Vent installations, combustion air is
In Direct Vent installations, combustion air is taken from
Table 6. Minimum Vent Pipe Length
Capacity Min. Vent Length*
045, 070, 090, 110
IMPORTANT
Figure 21.
045, 070,
090, 110
Standard or
Concentric?
See Table 5
Intake or
Exhaust?
2”, 2-1/2”
or 3”
Furnace capacity?
1
Which termination?
2
Which needs most
elbows?
3
How many?
4
Desired pipe size?
5
What is the altitude?
6
Use Table 7 to find
max pipe length.
7
All manuals and user guides at all-guides.com

507277-03CPage 16 of 53 mrcool.com
Maximum Allowable Intake or Exhaust Vent Length in Feet
Number
of 90
Elbows
Used
Capacity Capacity Capacity Capacity
045 070 090 110 045 070 090 110 045 070 090 110 045 070 090 110
1 20 15
n/a n/a
61 46 24
n/a
100 80 43
n/a
127 127 108 108
2 15 10 56 41 19 95 75 38 122 122 103 103
3 10
n/a
51 36 14 90 70 33 117 117 98 98
4
n/a
46 31
n/a
85 65 28 112 112 93 93
5 41 26 80 60 23 107 107 88 88
6 36 21 75 55 18 102 102 83 83
7 31 16 70 50 13 97 97 78 78
8 26 11 65 45
n/a
92 92 73 73
9 21 n/a 60 40 87 87 68 68
10 16 55 35 82 82 63 63
Number
of 90
Elbows
Used
Capacity Capacity Capacity Capacity
045 070 090 110 045 070 090 110 045 070 090 110 045 070 090 110
1 15 10
n/a n/a
53 38 22
n/a
90 70 39
n/a
111111 104 104
2 10
n/a
48 33 17 85 65 34 106 106 99 99
3
n/a
43 28 12 80 60 29 101 101 94 94
4 38 23
n/a
75 55 24 96 96 89 89
5 33 18 70 50 19 91 91 84 84
6 28 13 65 45 14 86 86 79 79
7 23
n/a
60 40
n/a
81 81 74 74
8 18 55 35 76 76 69 69
9 13 50 30 71 71 64 64
10 n/a 45 25 66 66 59 59
Table 7.
All manuals and user guides at all-guides.com

507277-03C Page 17 of 53mrcool.com
Figure 22. Typical Exhaust Pipe Connections
TRANSITION
2” 2”
2”
3”
Pipe sizedeterminedin Table7.
2”
2”
or
DO NOT transition from smaller
to larger pipe size in horizontal
runs of exhaust pipe. TOP VIEW
EXHAUST
INTAKE
* When transitioning up in pipe size, use the shortest length of 2” PVC pipe possible.
NOTE: Exhaust pipe and intake pipe must be the same diameter.
*2”
Maximum Allowable Exhaust Vent Lengths with Furnace Installed in a Closet or Basement Using Ventilated Attic or Crawl
Space for Intake Air in Feet
Number
of 90
Elbows
Used
Capacity Capacity Capacity Capacity
045 070 090 110 045 070 090 110 045 070 090 110 045 070 090 110
1 15 10
n/a n/a
61 46 24
n/a
100 80 43
n/a
127 127 108 108
2 10
n/a
56 41 19 95 75 38 122 122 103 103
3
n/a
51 36 14 90 70 33 117 117 98 98
4 46 31
n/a
85 65 28 112 112 93 93
5 41 26 80 60 23 107 107 88 88
6 36 21 75 55 18 102 102 83 83
7 31 16 70 50 13 97 97 78 78
8 26 11 65 45
n/a
92 92 73 73
9 21 n/a 60 40 87 87 68 68
10 16 55 35 82 82 63 63
NOTE
Table 8.
All manuals and user guides at all-guides.com

507277-03CPage 18 of 53 mrcool.com
Figure 23. Typical Intake Pipe Connections (Direct Vent Applications)
2” 2”
TRANSITION
2”
3”
TRANSITION
3”
Pipe sizedeterminedin Table7.
2”
2”
or
TOP VIEW
EXHAUST
INTAKE
* When transitioning up in pipe size, use the shortest length of 2” PVC pipe possible.
NOTE: Intake pipe and exhaust pipe must be the same diameter.
*2”
*2”
*2”
Intake Piping
AIR
INTAKE
SCREEN
(Provided)
NOTE: Air intake screen and elbow may be rotated, so that
screen may be positioned to face forwardor to either side.
Figure 24. Typical Air Intake Pipe Connections
All manuals and user guides at all-guides.com

507277-03C Page 19 of 53mrcool.com
Figure 25.
(Inlet Air from Ventilated Attic and Outlet Air to
Outside)
NOTE-The inletand outlet air openings shall each have a free area
of at least one square inch per 4,000 Btu (645mm2per 1.17kW) per
hour of the total input rating of all equipment in the enclosure.
VentilationLouvers
Inlet Air
(Minimum
12 in.(305mm) Above
attic floor)
Roof Terminated
Exhaust Pipe
Furnace
*Intake Debris
Screen
(Provided)
* See Maximum Vent Lengths table
CAUTION
Table 9.
Maximum Allowable Exhaust Vent Pipe Length (in ft.) without Insulation in Unconditioned Space for Winter Design
Winter Design Temperatures1
ºF (ºC) Vent Pipe
Diameter 045 070 090 110
32 to 21
(0 to -6)
PVC 2PP PVC 2PP PVC 2PP PVC 2PP
18 16 31 28 50 48 30 30
13 N/A 24 N/A 42 N/A 56 N/A
9 9 18 18 35 35 47 47
20 to 1
(-7 to -17)
9 8 18 16 32 29 30 30
5 N/A 13 N/A 24 N/A 34 N/A
N/A N/A 8 8 19 19 26 26
0 to -20
(-18 to -29)
5 3 12 10 22 19 30 27
N/A N/A 7 N/A 15 N/A 22 N/A
N/A N/A N/A N/A 10 10 16 16
1
2
NOTE
NOTE
NOTE
Figure 26.
(Inlet Air from Ventilated Crawl Space and Outlet Air
to Outside)
NOTE-The inlet andoutlet air openings shall each have a free area
of atleast one square inch per 4,000 Btu (645mm2per 1.17kW)pe
r
hour of the total input rating ofall equipment in theenclosure.
Roof Terminated
Exhaust Pipe
Furnace
Ventilation
Louvers
(Crawl space)
*Intake Debris Screen Provided)
Inlet Air
(Minimum
12 in.(305mm)
Above crawl
space floor)
Coupling or
3 in. to 2 in.
Transition
(Field Provided)
* See Maximum Vent Lengths table
All manuals and user guides at all-guides.com