NORTH STATES 8666 User manual

Superyard XT Manual Model 8666
Superyard XT - Model 8666 (manual can be used for Pet
Yard XT)
Thank you for purchasing our Superyard XT. Your Superyard XT is a second generation product
that represents years of engineering and product improvements, many of which were
recommended by customers such as yourself. Please take a few minutes to read and follow
the instructions and warning statements. In so doing, your Superyard XT should provide you
with years of safe, reliable service.
Please feel free to call or write with any comments or suggestions you may have, and thanks
again for your patronage.
NORTH STATES INDUSTRIES, INC.
1507 92nd Lane NE, Blaine, MN 55449
Phone: [phone] - Fax: [phone]
www.northstatesind.com
Parts Diagram
Important: Please remove all parts from the carton and review the parts diagram to familiarize
yourself with the gate and all components before you install gate.
Part No. DESCRIPTION PRICE EACH
PA Panel Assembly $14.00
XT1 Plunger $1.25
XT2 Spring $0.75
XT3 Blue Carpet Foot $0.75
XT4 Screw - #8 x 1 1/2" $0.15
XT5 Carrying Strap $2.25
EX 8662 Extension Kit $26.95
Pricing in U.S. Currency.
http://www.northstatesind.com/manual/sgxt/index.html (1 of 3)1/19/2010 9:13:03 AM

Superyard XT Manual Model 8666
Instructions
Your Superyard XT is completely assembled
at our factory. To make an enclosure, unsnap
the carrying strap, and unfold the panels to
create a hexagon shape (figure 1).
When done unfolding the panels, the two
unconnected panels will be oriented as
shown in figure 2. Make sure that the blue
carpet "foot" is up. To connect the panels
together, lift up on panel 1 and set opening
"A" over pin "B" (figure 3). Locate the slot on
the lower end of cylinder "D". This slot tapers
to an opening that pin "C" fits into. To fit pin
"C" into this opening, gently press down on
panel 1 and align pin "C" wit the end of the
slot in the cylinder "D". While maintaining
downward pressure on panel 1, lift slightly on
panel 2 and slide pin "C" along the slot and
into the opening (figure 4).
To Open Enclosure
To disconnect two adjoining panels, select
one of the three corners where the blue
carpet "foot" is facing up. Gently press down
on panel 1, and while lifting up on panel 2,
slide pin "C" clear of cylinder "D". Then, lift on
panel 1 until opening "A" has cleared pin "B".
Folding and Storage
Your enclosure is designed to fold compactly.
However, it must be folded in sequence.
Start at one panel, fold to the next panel
making sure that you fold it the correct
direction as shown (see figure 6).
Replacing a Panel
A broken panel can easily be replaced. Just
unlatch and remove broken panel (see
instructions for opening enclosures).
Your Enclosure as a Barrier
Your enclosure does not have the strength to
resist pressure if used in a "straight" position.
Be sure that it is not positioned in a straight
line. Make sure that each panel is at an angle
to the adjoining panel (figure 7).
Cleaning Instructions
Your enclosure is made from durable
weather-resistant plastic panels. To clean,
wash with a mild detergent, rinse with clean
water and allow to dry thoroughly.
Extension Kit
A two panel extension kit, Model No. 8662, is
available from your dealer or from the
factory. The kit contains two panels which
allow you to increase the size of your
enclosure from 18.5 square feet to 34.4
square feet.
http://www.northstatesind.com/manual/sgxt/index.html (2 of 3)1/19/2010 9:13:03 AM

Superyard XT Manual Model 8666
WARNING
●To prevent serious injury or death,
securely install enclosure and use
according to manufacturer's
instructions.
●Never use with a child able to climb
over or dislodge/open the enclosure.
●This product will not necessarily
prevent all accidents.
●NEVER LEAVE A CHILD
UNATTENDED.
●Use only with the locking/latching
mechanism securely engaged.
●This product intended for use with
children from 6 months up to 24
months of age.
●Do not use this product on a smooth
slippery surface, as child may be able
to push the enclosure to an unsafe
area.
●Do not attempt to use this enclosure in
temperatures less than 40 degrees F. or
damage may result.
●Do not use as a barrier for stairways,
stoves or heaters.
●Stop using enclosure if any parts are
missing or become damaged.
●Periodically check all fasteners to be
sure they are tight and secure.
●Do not use on uneven surfaces.
●Do not connect more than 8 panels in
one enclosure.
http://www.northstatesind.com/manual/sgxt/index.html (3 of 3)1/19/2010 9:13:03 AM