OEM 24482 Service manual

UNPACKING
After unpacking unit, inspect carefully for any damage that
may have occurred during transit. Check for loose, missing, or
damaged parts. If any damage is observed, a shipping damage
claim must be filed with carrier. Do not use the OEMTOOLS Drill
if broken, bent, cracked or damaged parts (including labels)
are noted. Any Drill that appears damaged in any way, operates
abnormally or is missing parts should be removed from service
immediately. If you suspect that the Drill was subjected to shock
load (a load that was dropped suddenly, unexpectedly, etc.)
immediately discontinue use until it has been checked by a
factory authorized service center.
Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and others by observing all
safety information, warnings, and cautions. Failure to comply with instructions could result in personal injury and/or damage to product or property. Please
retain instructions for future reference.
The following safety information is provided as a guideline to help you operate your Drill under the safest possible conditions. Any tool or piece of equipment
can be potentially dangerous to use when safety or safe handling instructions are not known or not followed. The following safety instructions are to provide
the user with the information necessary for safe use and operation. Please read and retain these instructions for the continued safe use of your service system.
Failure to follow instructions listed below may result in serious injury. In addition, make certain that anyone that uses the equipment understands and follows
these safety instructions as well.
Operating Instructions and Parts Manual 24482
10/15
2015 OEMTOOLS
HEAVY DUTY 1/2” 2VSR
CORDLESS 20V LI-ION DRILL
Thank you very much for choosing an OEMTOOLS Product!
For future reference, please complete the owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin
using it. This product is designed for certain applications only. OEMTOOLS cannot be responsible for issues arising from modification. We strongly
recommend this product is not modified and/or used for any application other than that for which it was designed. If you have any questions
relative to a particular application, DO NOT use the product until you have first contacted OEMTOOLS to determine if it can or should be
performed on the product.
Explanation of Safety Signal Words
CAUTION
: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
: Provide clarity and helpful information.
WARNING
CAUTION
NOTES
WARNING

2
Operating Instructions and Parts Manual 24482
HEAVY DUTY 1/2” 2VSR
CORDLESS 20V LI-ION DRILL
10/15
2015 OEMTOOLS
IMPORTANT INSTRUCTIONS
AND SAFETY RULES
1. Know your tool. Read this manual carefully. Learn the tool’s
applications and limitations, as well as, potential hazards specific
to it.
2. Keep work area clean and well lit. Cluttered or dark work areas
invite accidents.
3. Keep children away. All children should be kept away from the work
area. Never let a child handle a tool without strict adult supervision.
4. Do not operate this tool if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment
or reflexes are impaired while taking drugs. If there is any doubt, do
not attempt to operate.
5. Use safety equipment. Eye protection should be worn at all times
when operating this tool. Use ANSI approved safety glasses.
Everyday eyeglasses are NOT safety glasses. Dust mask, non-skid
safety shoes, hard hat or hearing protection should be used in
appropriate conditions.
6. Wear proper apparel. Loose clothing, gloves, neck-ties, rings,
bracelets or other jewelry may present a potential hazard when
operating this tool. Keep all apparel clear of the tool.
7. Don’t overreach. Keep proper footing and balance at all times when
operating this tool.
8. Check for damage. Check your tool regularly. If part of the tool is
damaged it should be carefully inspected to make sure that it can
perform its intended function correctly. If in doubt, the part should
be repaired. Refer all servicing to a qualified technician. Consult
your dealer for advice.
9. Keep away from flammables. Do not attempt to operate this tool
near flammable materials or combustibles. Failure to comply may
cause serious injury or death.
10. Store idle tools out of the reach of children and untrained persons.
Tools may be dangerous in the hands of untrained users.
11. Maintain tools with care.
12. Keep tools dry and clean.
13. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
14. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may
become hazardous when used on another tool.
15. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could
result in a risk of injury.
16. When servicing a tool, use only identical replacement parts. Use of
unauthorized parts or failure to follow maintenance instructions may
create a risk of injury.
17. Maintain a safe working environment. Keep the work area well lit.
Make sure there is adequate surrounding workspace. Keep the work
area free of obstructions, grease, oil, trash, and other debris. Do not
use this product in a damp or wet location.
18. Maintain labels and nameplates on this product. These carry
important information. If unreadable or missing, contact OEMTOOLS
for a replacement.
19. Before use, read and understand all warnings, safety precautions,
and instructions as outlined in the vehicle manufacturer’s service
manual. It is beyond the scope of this manual to properly describe
the correct procedure and test data for each vehicle.
20. Always perform vehicle service in a properly ventilated area. Never
run an engine without proper ventilation for its exhaust. Stop work
and take necessary steps to improve ventilation in the work area
if you develop momentary eye, nose, or throat irritation as this
indicates inadequate ventilation.
WARNING
Read Rules for Safe Operation and Instructions Carefully.
IMPORTANT SAFETY INSTRUCTIONS
The warnings, precautions, and instructions discussed in this manual
cannot cover all possible conditions and situations that may occur.
The operator must understand that common sense and caution are
factors which cannot be built into this product, but must be supplied
by the operator.
DISPOSAL
At the end of the useful life of the OEMTOOLS Drill, dispose of the
components according to all state, federal, and local regulations.
BATTERY DISPOSAL
Exposure to high temperatures can cause the batteries to explode; do
not dispose of in a fire. Some countries have regulations concerning
battery disposal. Follow all applicable regulations. Return used batteries
to a collection location for recycling.
PURPOSE
The OEMTOOLS Heavy Duty 1/2” 2VSR Cordless 20V Li-Ion Drill is used
for drilling holes, driving screws, loosening or tightening various materials
together with fasteners and other applications.
PRODUCT SPECIFICATIONS
Chuck Size: 1/2"
2 Speed Gear Box: 0-600 RPM and 0-2,000 RPM
Weight: 7 Lbs.
Charge Time: 1 Hour
Clutch: 21 + 1 Torque Clutch Setting
Includes: Lithium-Ion Battery with Charging Station
and Chuck
INSTRUCTIONS:
Always wear safety goggles and gloves.
DRILLING
1. If drilling in a small work piece, make sure it is securely held in a vise
or clamped to a secure platform such as a bench or table.
2. Install the correct drill bit in the chuck. Rotate the chuck body to
loosen or tighten the drill bit in the chuck. Never use the drill’s power
to rotate the chuck body.
3. Select the rotation direction to clockwise using the button located
above the trigger switch.

3
Operating Instructions and Parts Manual 24482
HEAVY DUTY 1/2” 2VSR
CORDLESS 20V LI-ION DRILL
10/15
2015 OEMTOOLS
4. Select the correct transmission speed. Use the slower speed for
drilling large holes.
5. Set the torque adjusting collar to the drilling position (drill icon on tool).
6. Slide the fully charged battery pack onto the base of the handle.
7. Mark the drilling point with a center punch when drilling in metal to
prevent the drill bit from slipping off center as you begin drilling.
8. Place the drill bit at the location of the hole to be drilled and squeeze
the trigger. The harder you squeeze, the faster the drill turns.
DRIVING SCREWS
1. Install the correct screwdriver bit in the chuck. Use the largest bit size
that will properly fit the screw. Make sure the flat sides of the bit are
gripped by the chuck.
2. Set the transmission speed to low speed.
3. Set the rotation directions to clockwise.
4. Set the torque collar to #10.
5. Place the screwdriver bit into the screw and hold the bit firmly into
the screw to prevent slippage and drive a test screw.
6. After driving a test screw, adjust the torque setting up or down so
the screw is driven to the desired depth without being over driven.
7. Release the trigger immediately when the torque clutch begins
to “rattle”.
8. Driven screws can be removed by reversing the direction of
the rotation.
CHARGE THE BATTERY:
NOTE: A discharged battery pack will be fully charged in approximately
one hour. Remove the battery pack from the tool when not in use.
WARNING
Always charge the battery pack indoors in a well-ventilated area. The
charger must never be subjected to wet conditions.
ELECTRICAL WARNING
POWER SOURCE CONNECTION POWER REQUIREMENTS
This product is designed to operate on a properly grounded
120 volt, 60Hz, single-phase alternating current (AC) power source
fused with a time delayed fuse or circuit breaker. It is recommended
that a qualified electrician verify the ACTUAL VOLTAGE at the
receptacle into which the product will be plugged and confirm that
the receptacle is properly fused and grounded.
DO NOT OPERATE THIS PRODUCT if the ACTUAL power source voltage
is less than 105 volts AC or greater than 132 volts AC. Contact a
qualified electrician if this problem exists. Improper performance
and/or damage to the product will result if operated on inadequate
or excessive power.
CONNECT TO POWER SOURCE
Consult a qualified electrician for proper installation of receptacle
at the power source. This product must be grounded while in use to
protect the operator from electrical shock. If you are not sure if your
outlet is properly grounded, have it checked by a qualified electrician.
Do not cut off the grounding prong or alter the plug in any way and
do not use any adapters between the product’s power cord and the
power source receptacle. Make sure the POWER switch is OFF then
connect the power cord to a properly grounded 120V, 60Hz, single
phase, 20 Amp power source.
Do not abuse cord. Never use the cord to carry tools or pull the plug
from an outlet. Keep cord away from heat, sharp edges or moving
parts. Replace damaged cords immediately. Damaged cords increase
the risk of electric shock.
1. Place the charger in a dry location near a 120V/60 Hz
electrical outlet.
2. Plug the charger into the electrical outlet.
3. The green LED light will turn on.
4. Turn the battery pack upside down and slide it onto the
charger.
5. The green LED light will turn off and the red LED light will
begin to flash indicating the battery pack is charging.
6. The red LED light will turn off and the green LED light will turn
on when fully charged.
7. Once the battery pack is fully charged, remove the charger
plug from the power source and remove the battery pack from
the charger.
NOTE: Do not charge batteries when the work area or the battery
temperature is at or below 32° F (0° C) or above 113° F (45° C).
Green Light Red Light Battery on
the Charger
Charging Status
On Off No Charger connected
to power supply
Off Flashing Yes Battery being
charged
On Off Yes Battery fully charged
Off On Yes Battery defective or
bad connection
On On Yes Battery too hot
or too cold to be
charged

4
Operating Instructions and Parts Manual 24482
HEAVY DUTY 1/2” 2VSR
CORDLESS 20V LI-ION DRILL
10/15
2015 OEMTOOLS
NOTE:
Not all components of the Drill are replacement items, but are illustrated as a convenient reference for
location and position in the assembly sequence.
1/2” Chuck
21 + 1 Torque
Clutch Setting
LED Work
light
Forward
and reverse
switch
Variable speed
trigger
Rechargeable
Lithium-Ion 20V
2.0 Ah Battery
Battery
Indicator
Lights:
(4) 100%,
(3) 75%,
(2) 50%,
(1) 25%
Charging
status
lights
20V Battery
Charging
Station
Rubber,
ergonomic grip
for comfort
2 Speed gear box
0-600 RPM;
0-2000 RPM
Belt hook clip
This symbol designates that this tool is listed with the
U.S. requirements by ETL Testing Laboratories, Inc.
conforms to UL Std. 60745-1, 60745-2-1 and 60745-2-2.
Intertek
3042597
JD6292