Orion OLS-32 User manual

OLS-32/40/46/70/8201NGB/P
1페이지 3/30/2012
1 of 38
Ver. 1.0 E
OLS-32/40/46/70/8201NGB/P
User’s Guide

OLS-32/40/46/70/8201NGB/P
2페이지 3/30/2012
2 of 38
CONTENTS
Safety Instructions ------------------------------------------------------------------- 3-7.
Introduction -------------------------------------------------------------------------- 8-10.
Connections ---------------------------------------------------------------------- 11-12.
SICP -------------------------------------------------------------------------------- 13-19.
Remote control ------------------------------------------------------------------------ 20.
Viewing the Menus ---------------------------------------------------------------- 21-32.
Specifications ----------------------------------------------------------------------- 33-38.

OLS-32/40/46/70/8201NGB/P
3페이지 3/30/2012
3 of 38
Safety Instructions
Do not use a damaged or loose plug.
This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
This may cause electric shock or fire.
Use only a properly grounded plug and receptacle.
An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose.
A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects
upon them, which could cause damage.
This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet.
This may cause fire.

OLS-32/40/46/70/8201NGB/P
4페이지 3/30/2012
4 of 38
Do not disconnect the power cord while using the LCD Display.
A surge may be caused by the separation and may damage the
LCD Display.
Do not use the power cord when the connector or plug is dusty.
If the connector or plug of the power cord is dusty,
clean it with a dry cloth.
Using the power cord with a dusty plug or connector may cause
electric shock or fire.
Do not drop the LCD Display when moving it.
This may cause damage to the product or the person carrying it.
Keep any flammable objects such as candles, insecticides or
cigarettes away from the product.
Otherwise, this may cause fire.
Keep any heating devices away from the power cable.
A melted coating may cause electric shock or fire.
Put down the LCD Display carefully.
Failing to do so may damage the LCD Display.

OLS-32/40/46/70/8201NGB/P
5페이지 3/30/2012
5 of 38
Do not place the LCD Display face down.
This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified
professional.
Installing the bracket by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall
(more than 10 cm / 4 inches) for ventilation purposes.
Poor ventilation may cause an increase in the internal temperature
of the product, resulting in a shortened component life and degraded
performance.
Do not spray water or detergent directly onto the LCD Display.
This may cause damage, electric shock or fire.
.
Keep the product away from places exposed to oil, smoke or
moisture; do not install inside a vehicle.
This may cause a malfunction, electric shock or fire.
In particular, avoid operating the LCD Display near water or outdoors
Where the LCD Display could be exposed to snow or rain.
Disconnect the plug from the outlet during storms or lightning or if
it is not used for a long period of time.
Failure to do so may cause electric shock or fire.

OLS-32/40/46/70/8201NGB/P
6페이지 3/30/2012
6 of 38
Do not install the product on an unstable, uneven surtace or a
location prone to vibrations.
Dropping the product may cause damage to the product or the
person carrying it.
Using the product in a location prone to vibrations mayshorten
the lifetime of the product or may cause the product to
catch fire.
When removing batteries from the remote control, be careful that
they are not swallowed by children. keep the batteries out of
children's reach.
If the batteries are swallowed, see a doctor immediately.
When replacing batteries, place the batteries in the correct +/-
polarity position as indicated on the battery holder.
The incorrect polarity may cause a battery to break or leak and
Cause fire, injury, or contamination (damage).
Use only specified standard batteries. Do not use new
and used batteries together.
` This may cause a battery to break or leak and may cause
fire, injury, or contamination (damage).
The batteries (and rechargeable batteries) is not ordinary refuse
and must be returned for recycling purposes.
The customer is responsible for returning the used or
rechargeable batteries for recycling purposes as the consumer.
The customer can return used or rechargeable batteries to a nearby
Public recycling center or to a store selling the same type of
the battery or rechargeable battery.

OLS-32/40/46/70/8201NGB/P
7페이지 3/30/2012
7 of 38
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such
as vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from
the AC receptacle.
17. The mains plug of the power supply cord shall remain readily operable.
18. An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective
earthing connection.
Note: Prolonged use of headphones at a high volume may cause health damage on your ears.
The lightning flash with arrowhead symbol within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

OLS-32/40/46/70/8201NGB/P
8페이지 3/30/2012
8 of 38
Introduction
LCD Display
Manual
User Manual CD
Cable
RGB Cable AC Power Cable
HDMI Cable (Option)
Other
Remote Control Batteries (AAA X 2)

OLS-32/40/46/70/8201NGB/P
9페이지 3/30/2012
9 of 38
Front
1. IR
- Aim the remote control towards this spot on the LCD Display.
2. LED
- LCD Power Status display(On : BLUE / Off : RED)
3. OSD KEY Input(Power / Menu / Source / Left / Right / Up / Down)
a) Power : Turns the LCD Display On/ Off.
b) Menu : Displays the main On-Screen menu.
c) Source : Select Input Source
- HDMI PC COMPONENT AV
d) Left/Right : Moves from one menu item to another horizontally or adjusts selected menu
values. Adjusts the audio volume.
e) Up/Down : Moves from one menu item to another vertically or adjusts selected menu values.
1
2
a
b
c
d
e
3

OLS-32/40/46/70/8201NGB/P
10 페이지 3/30/2012
10 of 38
Rear
1. AC Power S/W On/Off
2. AC Power In (100V ~ 240V)
3. HDMI Input
4. DVI(HDMI Jack) Output
5. PC Input
6. RS-232 Output
7. RS-232 Input
8. Component(Input)
9. Component(Output)
10. AV Input
11. AV Output
12. PC Sound Input
13. Component Sound Input
14. AV Sound Input
3
4
5
6
7
8
9
10
11
12
13
14
2
1

OLS-32/40/46/70/8201NGB/P
11 페이지 3/30/2012
11 of 38
Connections
Cable Assemble (HDMI).
Cable Assemble (COMPONENT/Y,Pb,Pr).
Cable Assemble (AV).

OLS-32/40/46/70/8201NGB/P
12 페이지 3/30/2012
12 of 38
Cable Assemble (PC).
Cable Assemble (RS-232).

OLS-32/40/46/70/8201NGB/P
13 페이지 3/30/2012
13 of 38
SICP (Serial Interface Communication Protocol)
This document defines all the command and messages exchanged between the
Master (a PC or the other controller) and the Slave (the displays).
It also describes the ways to send or read the commands or the messages.
1. Protocol definition
SICP stands for “Serial Interface Communication Protocol”.
The protocol is specifically designed to allow data communication in half duplex multi-point environments,
but it can also be used for half duplex point-to-point RS‑232C communication.
2. Communication characteristics
A half duplex communication is implemented starting from the concept of a master-slave structure, where
the display is supposed to be the slave.
The first action is always taken by the master, which can be either a PC or any controlling device (acting
as server) interfaced to the monitor. After sending a command or a request in the appropriate format the
master receives from the slave an acknowledgement, which tells the transmitter whether the command is
not valid (or not executable, anyway) or it is accepted. In case of a request, the requested information is
sent back and it becomes the acknowledgement by itself.
3. How to connect a external equipment
Female Pin number Male Pin number
2 <------------------------------------------------------> 2
3 <------------------------------------------------------> 3
5<------------------------------------------------------> 5
4. Hardware Protocol
Baud rate : 9600 bps
Data bits : 8 bit
Parity bits : None
Stop bits : 1 bit
Handshake : None
5. Transmission Formats
This is the format that the computer will send to the display to execute commands .
The format for this command transmission is as follows:
( total 13 byte )
ex) <STX>001PWRWOFF0<ETX> ( Set ID : 1 , Power Off Send )
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
0
0
1
P
W
R
W
O
F
F
0
0x0d
Hex
ASCII (capital letter)
Hex
- STX : Start of Text ( 0x0f )
- ID1 ~ ID3 : Set ID ( 001~100 )
- CM1 ~ CM3 : Command ( PWR, MIN, MUT,RML,KPL…… )
- R/W : Read/Write
- DA1 ~ DA3 : Data ( Values )
- IND : Index
- ETX : End of Text ( 0x0d )

OLS-32/40/46/70/8201NGB/P
14 페이지 3/30/2012
14 of 38
6. OK Acknowledgement
The acknowledgement will be sent by the display to the computer to verify that the command has been
successfully received and executed. This format for this acknowledgement is as follows:
ex) <STX>001PWR#OFF#<ETX> ( Set ID : 1 , Power Off Acknowledgement )
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
0
0
1
P
W
R
#
O
F
F
#
0x0d
Hex
ASCII (capital letter)
Hex
7. Error Acknowledgement
The Error Values will be sent by the display to the computer to verify that the command has been
successfully received and executed.
This format for this Error Values is as follows:
ex) <STX>001PWRERROR<ETX> ( Set ID : 1 , Power Off Error )
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
0
0
1
P
W
R
E
R
R
O
R
0x0d
Hex
ASCII (capital letter)
Hex
8. How to choose display ID number
♦Read Set ID Number
* Attention : Read SetID Function must be only one connect Monitor (1 pc : 1 monitor)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
F
F
F
S
I
D
R
0
0
0
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : “FFF” ( Set ID )
- DA1 ~ DA3 : “000” ( Don’t care )
Ex) <STX>FFFSIDR0000<ETX> ( Read Set ID )
Acknowledge => <STX>001SID#001#<ETX> ( Set ID : 1 )
♦Write Set ID Number
* Attention : Write SetID Function must be only one connect Monitor (1 pc : 1 monitor)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
F
F
F
S
I
D
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : “FFF” ( Set ID )
- DA1 ~ DA3 : “001” ( Set ID Number )
Ex) <STX>FFFSIDR0010<ETX> ( Write Set ID : 1 )
Acknowledge => <STX>001SID#001#<ETX>

OLS-32/40/46/70/8201NGB/P
15 페이지 3/30/2012
15 of 38
9. Command List
♦Power On/Off (PWR)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
P
W
R
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “-ON” : Power On
“OFF” : Power Off
Ex) <STX>001PWRWOFF0<ETX> ( Power Off )
Acknowledge => <STX>001PWR#OFF#<ETX>
♦Remote Control Lock On/Off (RML)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
R
M
L
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “-ON” : Lock On
“OFF” : Lock Off
Ex) <STX>001RMLW-ON0<ETX> ( Lock On )
Acknowledge => <STX>001RML#-ON#<ETX>
♦Keypad Control Lock On/Off (KPL)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
K
P
L
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “-ON” : Lock On
“OFF” : Lock Off
Ex) <STX>001KPLW-ON0<ETX> ( Lock ON )
Acknowledge => <STX>001KPL#-ON#<ETX>
♦Source Change (MIN)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
M
I
N
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “DVI” : DVI
“COM” : Component
“-PC” : PC(D-SUB)
“-AV” : AV(Composite)
Ex) <STX>001MINWDVI0<ETX> ( Source DVI )
Acknowledge => <STX>001MIN#DVI#<ETX>

OLS-32/40/46/70/8201NGB/P
16 페이지 3/30/2012
16 of 38
♦Virtual Remote Control (RMT)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
R
M
T
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “MEN” (Menu)
“SOU” (Source)
“LEF” (Left & Volume-)
“RIG” (Right & Volume+)
“ENT” (Enter)
“-UP” (Up)
“DOW” (Down)
“EXI” (Exit)
Ex) <STX>001RMTWSOU0<ETX> ( Remote Source Button)
Acknowledge => <STX>001RMT#SOU#<ETX>
♦Horizontal Set Count (HSC)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
H
S
C
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “001” ~ “010”
Ex) <STX>001HSCW0100<ETX> ( H-Set Count 10 )
Acknowledge => <STX>001HSC#010#<ETX>
♦Vertical Set Count (VSC)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
V
S
C
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “001” ~ “010”
Ex) <STX>001VSCW0100<ETX> ( V-Set Count 10 )
Acknowledge => <STX>001VSC#010#<ETX>
♦Display Sequence (SDS)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
S
D
S
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “001” ~ “100”
Ex) <STX>001SDSW0010<ETX> ( Display Sequence 1 )
Acknowledge => <STX>001SDS#001#<ETX>

OLS-32/40/46/70/8201NGB/P
17 페이지 3/30/2012
17 of 38
♦Horizontal Edge Adjust (HEG)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
H
E
G
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “000” ~ “200”
Ex) <STX>001HEGW0300<ETX> ( H-Edge Adjust 30 )
Acknowledge => <STX>001HEG#030#<ETX>
♦Vertical Edge Adjust (VEG)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
V
E
G
W
0
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “000” ~ “200”
Ex) <STX>001VEGW0400<ETX> ( V-Edge Adjust 40 )
Acknowledge => <STX>001VEG#040#<ETX>
♦Color Adjust DVI (FCD)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
F
C
D
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “000” ~ “255” ( Color Value )
- R/W : “W” (Write)
“R” (Read)
- IND : “0” ( Sub-Brightness)
“1” ( R-Offset )
“2” ( G-Offset )
“3” ( B-Offset )
“4” (Sub-Contrast )
“5” ( R-Gain )
“6” ( G-Gain )
“7” ( B-Gain )
Ex) <STX>001FCDW1004<ETX> ( Write : DVI Sub-Contrast 100 )
Acknowledge => <STX>001FCD#1004<ETX>
Ex) <STX>001FCDR0002<ETX> ( Read : DVI G-Offset )
Acknowledge => <STX>001FCD#1102<ETX> ( G-Offset:110 )

OLS-32/40/46/70/8201NGB/P
18 페이지 3/30/2012
18 of 38
♦Color Adjust PC(D-SUB) (FCP)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
F
C
P
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “000” ~ “255” ( Color Value )
- R/W : “W” (Write)
“R” (Read)
- IND : “0” ( Sub-Brightness)
“1” ( R-Offset )
“2” ( G-Offset )
“3” ( B-Offset )
“4” (Sub-Contrast )
“5” ( R-Gain )
“6” ( G-Gain )
“7” ( B-Gain )
Ex) <STX>001FCPW1100<ETX> ( Write : PC Sub-Brightness 110 )
Acknowledge => <STX>001FCP#1100<ETX>
Ex) <STX>001FCPR0001<ETX> ( Read : PC R-Offset )
Acknowledge => <STX>001FCP#1202<ETX> ( G-Offset : 120)
♦Color Adjust COMPONENT (FCC)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
F
C
C
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “000” ~ “255” ( Color Value )
- R/W : “W” (Write)
“R” (Read)
- IND : “0” ( Sub-Brightness)
“1” ( R-Offset )
“2” ( G-Offset )
“3” ( B-Offset )
“4” (Sub-Contrast )
“5” ( R-Gain )
“6” ( G-Gain )
“7” ( B-Gain )
Ex) <STX>001FCCW1004<ETX> ( Write : Component Sub-Contrast 100 )
Acknowledge => <STX>001FCC#1004<ETX>
Ex) <STX>001FCCR0002<ETX> ( Read : Component G-Offset )
Acknowledge => <STX>001FCC#1102<ETX> ( G-Offset : 110 )

OLS-32/40/46/70/8201NGB/P
19 페이지 3/30/2012
19 of 38
♦Color Adjust AV (FCA)
STX
ID1
ID2
ID3
CM1
CM2
CM3
R/W
DA1
DA2
DA3
IND
ETX
0x0f
F
C
A
0x0d
Hex
ASCII (capital letter)
Hex
- ID1 ~ ID3 : Set ID (“001” ~ “100”)
- DA1 ~ DA3 : “000” ~ “255” ( Color Value )
- R/W : “W” (Write)
“R” (Read)
- IND : “0” ( Sub-Brightness)
“1” ( R-Offset )
“2” ( G-Offset )
“3” ( B-Offset )
“4” (Sub-Contrast )
“5” ( R-Gain )
“6” ( G-Gain )
“7” ( B-Gain )
Ex) <STX>001FCAW1004<ETX> ( Write : AV Sub-Contrast 100 )
Acknowledge => <STX>001FCA#1004<ETX>
Ex) <STX>001FCAR0002<ETX> ( Read : AV G-Offset )
Acknowledge => <STX>001FCA#1102<ETX> ( G-Offset : 110 )

OLS-32/40/46/70/8201NGB/P
20 페이지 3/30/2012
20 of 38
Remote control
1. POWER : Turns the LCD Display On and Off
2. UP : Control the UP cursor in the menu
3, LEFT : Control the LEFT cursor in the menu
4, RIGHT : Control the RIGHT cursor in the menu
5, ENTER : Control the ENTER cursor in the menu
6, DOWN : Control the DOWN cursor in the menu
7. MENU : Displays the main On-Screen menu
8. SOURCE : Select Input Source
- HDMI PC COMPONENT AV
9. EXIT : Exit the On-Screen menu
2
1
3
4
5
7
6
8
9
7