Panasonic ziaino F-JPW50H User manual

Thank you very much for purchasing this Panasonic product.
Please read these operating instructions carefully before operation and maintenance.
Also, be sure to read the “SAFETY PRECAUTIONS” section (P.2~5) before use.
Failure to comply with instructions could result in injury or property damage.
Please retain this booklet for future reference.
F-JPW50H
…………………………… 2~5
……………………………
6
6
………………………
………………… 7~10
………………………………………… 13~15
………………………………………………… 11~12
……
16~18
……………………………… 12
…………………………………… 19~26
………… 25
……………………… 26
…………………………… 26
……………………………
29~32
………………………
…………………
…………………………
………………………………………………………
27
27
28
29
… …………………………
31~32
……………………… ………………
OPERATING INSTRUCTIONS
ziaino®Air Treatment Unit
Model No.
This product is for indoor use only
OPERATION
CONFIRMATION AND SETUP MAINTENANCE OTHER
INFORMATION
CONTENTS
SAFETY PRECAUTIONS
SETTING REQUIREMENTS
OPERATING REQUIREMENTS
EACH PARTS IDENTIFICATION
OPERATION
WATER SUPPLY/DRAINAGE METHOD
ADDING A SALT TABLET
SETUP
WHEN REPLACING THE ELECTRODE UNIT
MAINTENANCE
TROUBLESHOOTING
●
●
●
●
32SPECIFICATIONS
WHEN IDLE FOR A LONG TIME
LIST OF ERROR CODES
OPTIONAL ACCESSORIES
WHEN THE LOUVER SHIFTS
WHEN THE FLOATER FALLS OFF
FAQ
FURTHER INFORMATION

2
■
■
■
■
■
■
■
■
■
■
■
●
●
This product is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the product by a person responsible for the
safety. Children should be supervised to ensure that they do not play with the product.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Disconnect power supply before maintenance and filling water and water drainage.
For cleaning and descaling see "maintenance“ and regarding filling (water supply) see
“WATER SUPPLY/DRAINAGE METHOD”.
The safety precautions should be strictly followed in order to prevent injury or damage to properties.
The following symbols differentiate the levels of danger or injury that may result if the product is
not used correctly as instructed.
CAUTION
WARNING
WARNING
Those things shown in this column indicate that
there is possibility of causing death or severe
injury.
Those things shown in this column indicate that
there is possibility of causing minor injury or
damage to properties.
The following symbols are used to indicate the type of instructions that need to be followed.
(The symbols given below are examples.)
This symbol indicates an action that must
not be performed.
This symbol indicates an action that must
be performed.
Do not pull the power cord
when carrying or storing the
product.
(Otherwise, the power
cord may be damaged
with the possibility of
fire or electric shock.)
●
Do not damage the power
cord or power plug.
Do not use power other than
the rated voltage.
Do not cut, modify, excessive distort,
twist, squeeze the power cord, and
do not place it near heat sources,
place heavy weight on it, etc.
(Otherwise, the power cord may be
damaged with the possibility of fire
or electric shock.)
(Otherwise, the power cord may be
overheated and induce fire.)
●
Insert the power plug into
the power socket completely.
Do not use damaged power plug or
loose power socket.
(If the power plug is not fully
inserted, electric shock
may occur, or a fire
may be caused due
to overheating of the
power cord.)
Clean the power plug
regularly.
Disconnect the power plug and wipe
it with dry cloth.
(If dust and humidity is found on the
power plug, which may cause
damage to insulation, causing fire.)
When the product will
not be used for a long
period, disconnect the
power plug.
Please strictly follow
SAFETY PRECAUTIONS

3
■
■
■
●
●
●
●
●
■
■
■
■
■
■
WARNING
For hospitals, rehabilitation
centers or the like, please pay
attention to the operating
places of this product. Make
sure that customers with
implanted medical
pacemakers keep their
pacemaker implantation sites
away from the opening and
closing part of the front
panel, tank and tray of this
product.
(Otherwise, the magnets on the
product may negatively affect the
pacemaker.)
Do not touch the power plug
with wet hands.
(Otherwise, electric
shock may occur.)
Do not use acidic detergents
or citric acid.
(Otherwise, toxic gas may be
produced, which is harmful to your
health.)
Do not insert your fingers,
metallic objects or others into
the air inlet, air outlet or gaps.
(Otherwise, you may be
hurt by the inner units
with the possibility of
electric shock or injury.)
Do not let the product get
wet.
Do not place cups, etc.
on the main unit.
(Otherwise, the product
may short circuit with
the possibility of fire
or electric shock.)
(Otherwise, electric shock, fire or
smoke may occur.)
<Examples of abnormality/
malfunction>
Operation stops after the power
cord is touched.
Abnormal noise or severe vibration
occurs during operation.
The main unit becomes abnormally
hot or emits a smell of burning.
Leakage.
There is any other abnormalities or
malfunction.
Please stop operating immediately
and disconnect the power plug,
and contact the dealer to check
and repair.
In case of any abnormality
or malfunction, immediately
stop using the product and
disconnect the power plug.
Do not disassemble or modify
the product.
Contact the dealer for repair.
(Otherwise, the product may catch
fire or malfunction, thus resulting in
fire or electric shock.)
Do not disassemble or modify
the electrode unit.
(Injury may be caused due to the
electrode plates after disassembly.)
(Otherwise, the product might
operate with the possibility of
electric shock or injury.)
Make sure to disconnect the
power plug before cleaning
the product.
Please strictly follow
SAFETY PRECAUTIONS
CONFIRMATION AND SETUP
→
→

4
■
■
■
■
■
■
■
■
■
■
■
■
■
CAUTION
(Otherwise, the product
may fall over and injury
may occur, the water
may spill out and fire,
electric shock may occur
or wet furniture, etc.)
(Otherwise, the product may crack
and injury may occur.)
(Otherwise, current may
leak with the possibility
of fire or electric shock.)
Do not place the product in
the incline and unstable place
or at heights.
Do not place the product in
the place where oil fume is
emitted, such as in kitchens.
Do not place the product in
the place where the
temperature or humidity is
extremely high, or watery
area, such as bathroom.
Do not use the product in the
place where the air outlet
faces animals or plants directly.
(Otherwise, a fire or smoke
may occur due to ignition
in the product.)
Families with children should pay
more attention.
(Otherwise, it may
cause discomfort to
the animals and dry
out the plant.)
Do not use the product in
the place where oil or
inflammable gas may
be leaked.
Do not sit on or lean against
this product.
(Otherwise, the product may fall over
and injury may occur, the water may
spill out and fire, electric shock may
occur or wet furniture, etc.)
Do not push over or overturn
the product.
(Otherwise, the water may spill out
and fire, electric shock may occur or
wet furniture, etc.)
Do not operate this product
in places where indoor
fumigation type insecticides
are being used.
(Otherwise, chemical residue may
build up inside the product and
discharge from the air outlet, which
is harmful to your health.)
Ventilate the room with fresh air
thoroughly after using insecticides
before operating the product.
Do not clean the product
with gasoline or other
volatile mixture solvents, and
avoid contacting with spray
insecticides.
(Otherwise, the product may crack
or short circuit with the possibility
of injury, fire or electric shock.)
Do not place the product
near combustible materials
such as lighted cigarette,
incense, etc.
(Otherwise, these may be absorbed
into the product with possibility of
fire.)
Do not drink the water in the
tank or tray, or feed animals
or water plants with it.
Do not use a punctured or
damaged tank or tray.
(Otherwise, human health may be
harmed and adverse effects may be
caused.)
(Otherwise, discoloration or
deterioration of the floor may be
caused.)
(Otherwise, dirt, mold or rust may
be caused.)
Do not let the wind blow
directly onto walls or hand-
rails or any other metal
objects.
Please strictly follow
SAFETY PRECAUTIONS
→

5
■
■
■
■
■
■
■
■
■
■
CAUTION
Do not add chemicals, air
fresheners, essential oils, etc.
into the tank or tray.
(Otherwise, toxic gas may be
produced, which is harmful to your
health. Or, the water supply tank or
tray may be damaged, thus wetting
the floor and resulting in
discoloration or deformation.)
When disconnecting the
power plug, hold the power
plug instead of the power
cord.
(Otherwise, the power
cord may be damaged
with the possibility of
fire or electric shock.)
Keep the room well-ventilated
when using the product
together with a burner.
(Otherwise, carbon
monoxide poisoning
may occur.)
This product cannot
remove carbon
monoxide.
(Otherwise, discoloration or
deterioration of the floor may be
caused.)
When carrying the product.
Turn off the product and disconnect
the power plug, take out the tank, and
pour water out of the tank and tray.
(Otherwise, the product may slip out
injury may occur.)
Hold the left and right handles, but
not the louver, front panel and the
side panel to carry the product.
(If water spills out on the floor, etc.,
discoloration or deterioration may be
caused due to the bleaching effect of
hypochlorous acid.)
Make sure that no water spills
out when carrying the tank or
tray. If any water spills out,
wipe it off immediately.
(Otherwise, the sink and water pipe
may oxidize to form rust.)
When draining the water,
turn on the tap to flush the
sink clean.
●Replace the water in the tank with
new tap water every day.
(When the product is not operating, a
foul odor may occur due to mildew
and miscellaneous bacterium breeding
caused by dirt or incrustation, which
may be harmful to your health.)
Clean the tank and the interior
of the main unit frequently.
(Otherwise, physical discomfort may
be caused.)
When you feel uncomfortable,
stop using the product
immediately and consult a
doctor at once.
When moving the product by
the wheels
When it is inconvenient or difficult to
wheel the product, lift and move the
product.
Please unlock the fixed hook from
wheels, then moving the
product. (P. 7)
(Otherwise, the
product iseasily
pushed over and
result ininjury.)
(Otherwise, the support surface may
be scratched or the product may fall
over.)
(Otherwise, the floor or
carpetmay be scratched.)
Move the product
horizontally.
Fixed hook
[Unlock]
(Move the
fixed hook
up)
Please strictly follow
SAFETY PRECAUTIONS
CONFIRMATION AND SETUP

■
■
■
■
■■
■
■
●
■
■
■
■
■
■
■
■
■
●
●
6
(Poor ventilation may cause the internal
temperature of the main unit to rise, thus
resulting in malfunction.)
Keep a safe distance during use as
instructed below.
When used beside a wall, etc.
150 cm or above air outlet
1 cm or above
30
cm or above
30
cm or above
air inlet
Place the main unit indoors and use
it within the ambient temperature
range of 5 °C to 35 °C.
Near objects such as TV and radio.
Keep a distance of 1 m or above.
(Otherwise, visual disturbances or noises may
be caused.)
Where the product will be exposed directly to
sunlight, outlet of air conditioner or heat, etc.
(Otherwise, deformation, deterioration,
degeneration, discoloration or malfunction
may be caused.)
Do not set the product in the following places.
Do not use the same power socket with TV,
radio, etc.
(Otherwise, visual disturbances or noises may
be caused when inserting the power plug.)
In this case, insert the power plug into
another power socket.
Do not put any obstacles at the inlet and
outlet of the product.
(Otherwise, it may affect product performance.)
(Otherwise, the product
may malfunction.)
Do not place any object
on the product.
(Otherwise, dust may build up inside the
main unit, thus resulting in malfunction.)
Do not use the product with the HEPA
composite filter removed.
(Otherwise, mildew and miscellaneous
bacterium breeding may be caused as
sterilization is not available.)
Make sure that there is water in the tank
and keep the power plug inserted since
the cleaning operation (Page 15) will start
automatically once the product stops working.
Do not disconnect the power plug if the
product will not be in use for a short time.
(Otherwise, it may cause mildew and
miscellaneous bacterium breeding since the
effect of hypochlorous acid is weakened
while the power is off.)
There is no problem if the power plug is
disconnected briefly.
If the product will not be in use for a
long time, disconnect the power plug,
and empty the tank and tray.
(If the product inhales cigarette smoke, the
interior of the main unit may become dirty
with cigarette tar, and dirty water containing
cigarette tar or other components may be
blown out from the main unit.)
(Otherwise, product life may be shorten
and the replacement cycle of the electrode
unit, sterilization filter and HEPA composite
filter may be shortened.)
It is recommend that do not use the
product in a smoking environment.
Using the product continuously at the same
location may result in dirty surrounding walls
due to the air inhaled by the product. You are
recommended to clean the walls regularly.
Clean the walls regularly.
(Operating with frozen water may cause
malfunction.)
(Otherwise, misoperation or malfunction may
be caused.)
Do not block the air outlet.
When there may be freezing, please empty
the tank and tray.
About the salt tablet
The salt tablet is applicable to this series of
product only.
Be sure to use the supplied or optional salt
tablet (Page 26).
Tighten the cover to keep the salt container
sealed after unpacking.
Do not swallow any salt tablets.
If salt tablets are swallowed by accident, drink
enough water immediately. (It is recommended
to drink 500 mL water per salt tablet.)
If too many salt tablets are swallowed, or if a
patient with hypertension or heart disease
swallows salt tablets by accident, consult a
doctor at once.
Where window or other objects may obstruct
the humidity sensor and odor sensor.
(Otherwise, the sensors may not work normally.)
SETTING REQUIREMENTS
OPERATING REQUIREMENTS
→
→

■
7
Main unit
Handle
(left and right)
Handle
(left and right)
Air inlet
(left and right)
Air inlet
(left and right)
Power cord
Front panel
Before the first use, please remove
the cardboard and blue tape.
Cardboard
Blue
tape
(For how to remove the front
panel, please see page 21.)
Side panel
Power plug
Control panel
Water-level
window
Status indicator
Humidity sensor
Wheels
(The product may move on a slippery floor even if wheels are locked.)
Fixed hook Fixed hook
Press down
to lock
Move up
to unlock
Lock the wheels: press down the fixed hook.
Unlock the wheels: move the fixed hook up.
Odor sensor
(The open method of side panel)
HEPA composite filter
EACH PARTS IDENTIFICATION
CONFIRMATION AND SETUP

●
8
Blue tape
Maintenance
panel
Air outlet
Louver
Automatic salt tablet
adding assembly
The automatic salt tablet
adding assembly is removable.
To install it, with the buckle
side facing forward, embed
it into the holes on the main
unit.
(two, inside)
Water
collection
part
Before the first use, please
remove the blue tape for
fixing the electrode unit.
(Referred to as the
tank in the main text)
To remove it, press the left
and right buckles with your
fingers at the same time.
Accessories
Salt tablets can be
stored inside the
main unit.
Salt tablet
(About 300 tablets)
Water supply
tank
Slider latch
Floater
Sterilization
filter
assembly
Tray
Anti-fungus
assembly (inside)
Electrode unit (inside)
Digital display
EACH PARTS IDENTIFICATION
●

9
●
●
●
→
→
→
●
Control panel
Power Off/On
button
Air volume
button/indicator
Safety lock
button/indicator
Timer button/
indicator
When the drain indicator lights on
When the drain indicator blinks
If the drain indicator blinks, it is required to
empty the tray.
For the detailed drainage method, see
page 16~18.
The indicator lights on when the tank is not
installed.
The indicator lights on when the side panel is
opened.
While the side panel is open, the side panel
confirm indicator stays steady on.
The product enters preparatory operation in
about 20 seconds after the side panel is closed.
After the preparatory operation is completed,
the product returns to the operation mode
before the side panel is opened.
If the side panel is opened during operation,
the product will sound "BIBIBIBIBI", the side
panel confirm indicator will light on and the
operation will be paused.
After the product is powered on for 1 week
(168 hours), if the water refill indicator does
not light on the 7th time, the drain indicator
blinks, notifying that the drainage time is
approaching. (The product can still operate
even if the drain indicator blinks.)
If the water tank is removed while the
drain indicator is blinking, the drain
indicator lights on.
After the last drainage, the drain indicator
lights on simultaneously when the water
refill indicator lights on the 7th time.
Turbo button/
indicator
Water refill
indicator
When the indicator lights on, the automatic
cleaning operation is in progress. (Page 15)
If this indicator lights on, the product is
abnormal.
If this indicator lights on, please check
the error code displayed on the digital
display. (Page 31~32)
If this indicator lights on and the product
sounds "BIBI" for five times, it is required
to refill the water tank with water.
(Page 16)
If the cleaning reset indicator, the electrode
reset indicator lights on, or if ”00” appears
on the digital display of the maintenance
panel (the automatic salt tablet adding
assembly runs out of salt tablets), the
maintenance indicator lights on,
maintenance should be performed
according to the instructions.
Water refill indicator
Drain
indicator
Drain indicator
If the drain indicator lights on, drainage
is required.
Clean
indicator
Clean indicator
Maintenance
indicator
Maintenance indicator
Check
indicator
Check indicator
Tank confirm
indicator
Tank confirm indicator
Side panel
confirm
indicator
Side panel confirm indicator
EACH PARTS IDENTIFICATION
CONFIRMATION AND SETUP

●
●
10
■
●
→
■
■
●
→
●
→
→
●
■
■
→
●
Electrode reset
button/indicator
Cleaning reset
button/indicator
A button dedicated
for market service
A button dedicated for market service
This button is used for factory maintenance and spot check.
(No customer operation is required.)
Status indicator
This indicator shows the air pollution level and the product operation status.
Light on Light on Light on Light on Light on
Light on Light on Light on
Light on
The status indicator can be turned off. (Page 29)
The indicator lights on in blue
(when the air is clean)
The indicator lights on in red
(when air pollution is detected)
One in red:
dirty
Three in red:
very dirty
The indicator blinks in red (various notifications)
When the water refill indicator stays steady on
for more than 4 hours, three indicators instead
of one indicator will blink in red.
One in red: It is time
to add salt tablet, it
is required to replace the electrode unit, or the
clean indicator, the check indicator, the water
refill indicator, the drain indicator, the tank
confirm indicator or the side panel confirm
indicator lights on.
The indicator blinks in blue (operation status)
Preparatory operation is in progress
Drying operation of the sterilization
filter is in progress
When the digital display shows an error code
Please check the error code
When the digital display scrolls automatically
When the electrode reset indicator blinks or lights on
The drain indicator lights on.
Please perform drainage.
Blinking: It is almost time to replace the electrode unit.
Please replace the electrode unit.
Please replace the electrode unit.
Please perform maintenance.
After installation, press and hold for approximately
3 seconds.
If you clean the product before the cleaning reset
indicator lights on, press and hold for
approximately 3 seconds as well.
Clean the tray, anti-fungus assembly, sterilization filter
assembly, and HEPA composite filter, and then install
them back into the main unit.
When the cleaning reset indicator lights on
(About once a month)
Steady on: The product does not work.
One letter and two digits of the error code are
displayed alternately as a reminder.
If the product continues to operate and the air
remains clean, based on the purification time,
1 to 5 blue status indicators will light on.
1~5 in blue: normal operation is in progress
When the status indicator lights on, the air pollution level is displayed; when it blinks, the product
operation status and various notifications are displayed.
Maintenance panel
Digital display
EACH PARTS IDENTIFICATION

11
12
1
2
Remove the tank from product.
Before startup Remove the tank
Fill in the label with
the first date of use.
Please be sure to read page 2~5
before you are ready to power
on the product.
Open the side panel.
Remove the tank, unscrew the tank cover.
Turn it upside down
when adding water
The water tank can stand upright.
Be careful not to overturn it.
Tank cover
Tank
3
·
·
1
2
Filling the water tank up and putting salt tablets
into the automatic salt tablet adding assembly
Filling the water tank up
Filling the water tank up
Be sure to fill it
up with water.
During tightening, hold the water tank
with your hand to avoid tilting.
Water fill line
Screw the tank cover tightly.
Notice
SETUP
OPERATION

12
6
3
4
→
·
·
5
7
·
■
●
●
●
●
●
■
■
1
2
1
2
Filling the water tank up and putting salt tablets
into the automatic salt tablet adding assembly
Installing the water tank back
and closing the side panel
Putting salt tablets into the automatic
salt tablet adding assembly
Filling the water tank up
(When the product operates in the “Turbo” mode in an
environment where the room temperature is 20 °C and the relative
humidity is 30%.)
A full tank of water supports continuous operation of
approximately 6 hours. The continuous operation time
may be longer in the “Air volume” mode.
Do not overfill the assembly with salt tablets.
Make sure all of the following
indicators are off.
Be sure to tighten the cover of the automatic salt tablet
adding assembly until the two △marks are aligned.
Tighten the cover of the automatic salt tablet adding
assembly and install the assembly into the main unit.
Be sure to use the supplied salt tablets or the
replacement salt tablets specified in "OPTIONAL
ACCESSORIES" (Page 26).
Tightening
Refill the automatic salt tablet adding assembly with salt
tablets (about once every 6 months).
For how to remove the automatic salt tablet adding assembly,
see page 8.
Remove the automatic salt tablet adding assembly from the
main unit, open the cover and put 60~70 salt tablets into the
assembly.
Put the tank back to the product.
Put the tank back to
the product and close
the side panel.
Close the side panel.
Connect the power
plug.
A salt tablet drops
automatically into
the tray.
Make sure to use the tap water.
(Because chlorination has been performed generally for tap water
and hence the miscellaneous bacterium is difficult to breed.)
Warm water above 40 ℃, or water mixed with detergents.
(Otherwise, the tank deformation may be caused.)
Do not use the following water.
Water mixed with chemicals, air fresheners and essential oils.
(Otherwise, the tank may be damaged and the furniture,
appliances, etc. may be wet. →Page 5)
Water from a water purifier, alkaline ion water, mineral water
(Otherwise, mildew and miscellaneous bacterium may multiply
fast.)
Well water
(Otherwise, mildew and miscellaneous bacterium breeding may
be caused, discoloration may occur, and the replacement cycle
of the electrode unit may be shortened.)
SETUP

13
Lo Hi
1●
·
●
2
●
Louver
When the product is operating, do not adjust the louver manually.
(Otherwise, it can not operate according to the set angle.)
If you adjusted them manually, please stop the product.
(The product can reset to the normal state when starts again.)
Notice
Start to operate.
Select air
volume mode
Select Turbo
mode
The product enters preparatory operation in about
20 seconds after the button is pressed.
After the preparatory operation is completed, the product
starts to operate.
The product does not blow out air during preparatory
operation.
(The status indicator lights on)
When used for the first time, the product operates with “Air
Volume” set to “Lo” and “Electrolytic Strength” to “Medium”.
From the next time, the product will start with the settings
when it stops operation last time.
(The status indicator blinks in blue.)
Press this button to
switch the air volume
level by level.
In “Turbo” mode, the electrolytic strength is “High” and
the product runs at its maximum air volume.
It can be set during preparatory operation.
(The indicator lights on)
(The indicator lights on)
3
4●
Stop operating. The product continues to blow air for about 10 seconds
after the button is pressed.
(The purpose is to drain the hypochlorous acid
accumulated in the main unit.)
OPERATION
OPERATION

14
●
■
●
●
■
(Press the button
for about 3 seconds)
The purpose is to prevent misoperation.
(The indicator
lights on)
With this setting, if you press any button other than , the product
will sound ”BI-BI-” and operation is not possible.
To cancel this mode
Press the button for about 3 seconds again. (The indicator lights off)
Press this button to
set a timer
(The timer indicator
lights on)
The water tank is removed before the timer is up. (The product stops working.)
The water tank runs out of water before the timer is up. (The product stops working.)
Cancel
(The indicator lights off)
The timer is cancelled in the
following cases:
After the timer is set to ”4” hours, when
only 2 hours are left, ”2” lights on on the
control panel.
When the drain indicator lights on, drainage is required. After completing drainage according to
the drainage method (Page 16~18), connect the power plug. Then, the timer indicators and
blink, indicating that drainage needs to be reset. Press and hold for approximately 3 seconds
to reset drainage.
If drainage is performed before the drain indicator lights on, after drainage has finished, you also
need to press and hold for approximately 3 seconds to reset drainage.
Drainage reset
Locking the operation
Timer
OPERATION

15
■
■
+
(Turbo mode “ ”)
Low Medium High
(You may smell some chlorine during electrolysis.)
You can only switch the electrolytic strength for
“Air volume”. The electrolytic strength for
“Turbo” mode is “High” and cannot be switched.
(The factory setting of the electrolytic strength
is “Medium”.)
If you are not satisfied with the smell in the room,
or if you want to improve the sterilization effect,
select “High” or “Turbo” mode.
The product is in standby mode
Select your desired electrolytic strength,
press and at the same time
to confirm and exit from the switching
state.
(The right figure shows the corresponding
electrolytic strength.)
In the switching state, when you press
, the indicator switches level by
level among , and .
The following figure shows the change of
electrolysis strength.
Press and hold the button for about
3 seconds to enter the switching state.
Selecting the electrolytic strength
●
●
●
(During the cleaning operation, a gentle breeze may blow out and the clean indicator lights on.
After cleaning, the clean indicator lights off.)
Cleaning operation (Auto)
In order to keep its inside clean, the product will automatically perform the cleaning operation
regularly.
Do not disconnect the power plug since automatic control is
active when the product is idle.
Please check that there is water in the tank as the cleaning
operation is not possible when the tank need to add water.
Notice
(Clean indicator lights on)
OPERATION
OPERATION

16
■
●
1
●
2
●
●
●
·
1
●
2
※
·
■
1
2
1
2
CAUTION
Remove the tank from the product
and fill it up with water.
Install the tank back to the product.
When it is time to empty the tray, the drain
indicator lights on.
For the time when the drain indicator lights on,
see page 9.
For how to remove the water tank, see “SETUP”
on page 11.
Drain the tray regularly (about once a
week).
Meanwhile, the digital display scrolls automatically
as a reminder. If the product is in operation, the
operation is stopped.
Notice
Make sure that no water spills
out when carrying the tank or
tray. If any water spills out,
wipe it off immediately.
(If water spills out on the floor, etc.,
discoloration or deterioration may
be caused due to the bleaching
effect of hypochlorous acid.)
Disconnect power supply before water
supply/drainage.
Water supply method
Drainage method
WATER SUPPLY/DRAINAGE METHOD
When the tank need to add water, the product
will sound “BIBI” 5 times and stop operating.
(The water refill indicator lights on.)
Water-level window
Used to check the
remaining amount of
water in the water
supply tank.
For how to remove the tank and fill it up,
see “SETUP” on page 11~12.
For how to reinstall the tank, see “SETUP” on
page 12.
When needed, salt tablets are automatically
added.
The automatic salt adding cycle is ”about 1
tablet per 3 days”. Do not add salt tablets every
time when you add water because the salt
concentration will be increased.
Slider latch (Sliding
while pinching.)
Remove the tray.
Slide up the slider latch to the top.
You cannot take the tray out without lifting
the slider latch (electrode unit). Therefore,
be sure to check that the electrode unit is
lifted before taking the tray out.
Remove the tray from the product.
Remove the tank from
the product.

17
3
·
●
4
①
③
②
●
■
1
2
3
1
2
3
Empty the tray.
Empty the tray.
Do not tilt the tray when carrying it.
If the tray is not emptied, the drain indicator
is always on and the product does not work.
Install the tray back to the product.
Install the tray back to the product
Drainage
Slider latch
(Sliding while
pinching.)
Make sure that the tray is securely installed on the
main unit.
Slide down the slider latch to the bottom.
Install the tray.
Set slider latch at the top position.
Tray
(Otherwise, the metal sink and
water pipe may oxidize to form
rust.)
When draining the water,
turn on the tap to flush
the sink clean.
Please hold the
sterilization filter
by hands
Water collection
part
Meanwhile, turn on the tap to
flush the sink clean.
Wipe the water off from the water collection
part (i.e. the dent used to collect water
dripping from the electrode unit) if any.
CAUTION
WATER SUPPLY/DRAINAGE METHOD
OPERATION

18
5
●
7
●
→
●
●
1
2
6
Filling the water tank up with water
and installing it back into the main unit Salt tablets dropping automatically
Make sure to run the ”Drainage reset”,
otherwise the product cannot operate.
Connect the power plug.
Close the side panel.
Make sure all of the following indicators are off.
The timer indicators and blink, indicating
that drainage needs to be reset. Press and hold
for approximately 3 seconds to reset
drainage.
Install the tank back to the main unit.
A salt tablet drops automatically
into the tray.
When a salt tablet drops into the tray, a ”click”
sound is heard.
Please add salt tablets. (Page 12)
If salt tablets are stuck in the automatic salt
tablet adding assembly, please remove them.
If the automatic salt tablet adding assembly runs
out of salt tablets, the maintenance indicator
lights on, ”00” is blinking on the digital display
of the maintenance panel and the product does
not work.
For how to fill the water tank up with water,
see “SETUP” on page 11~12.
Fill the tank with water and
install it back to the main
unit, then close the side panel.
Notice
WATER SUPPLY/DRAINAGE METHOD

19
■■
●
●
●
Do not use the detergents shown at right.
Precautions before maintenance
When using chemically treated cloth, be sure
to follow the instructions carefully.
WARNING
■
■■
CAUTION
(If water spills out on the floor, etc.,
discoloration or deterioration may
be caused due to the bleaching
effect of hypochlorous acid.)
Make sure that no water
spills out when carrying the
tank or tray. If any water spills
out, wipe it off immediately.
As the degree of dirtiness varies with the water quality and operating environment, maintenance
may be required even before the cleaning reset indicator lights on or before the specified time is
reached, as long as there is an unpleasant odor or the water in the tank is reduced at a slower
speed.
Alkaline detergent
Polish
acid detergents
Thinner
Kerosene Alcohol
Bleach
Make sure to disconnect the
power plug before cleaning
the product.
(Otherwise, the product might
operate with the possibility of
electric shock or injury.)
Do not use acidic detergents
or citric acid.
(Otherwise, toxic gas may be
produced, which is harmful to
your health.)
(Otherwise, the metal sink and
water pipe may oxidize to form
rust.)
When draining the water,
turn on the tap to flush
the sink clean.
Do not clean the product
with gasoline or other
volatile mixture solvents,
and avoid contacting with
spray insecticides.
(Otherwise, the product may crack
or short circuit with the possibility
of injury, fire or electric shock.)
MAINTENANCE
MAINTENANCE

20
●
Sterilization
filter assembly
Tray
Anti-fungus
assembly (inside) Electrode
unit (inside)
Slider latch
Air inlet
When maintenance, do not leave the removed parts unattended.
(Otherwise, it may cause tripping or damage.)
Notice
Automatic adding
salt tablet assembly.
(two, inside)
Floater
MAINTENANCE
(Referred to as the
tank in the main text)
Water supply
tank