Park Supplies PlayBlox Instruction Manual

0800 752 947
GUIDELINES FOR USE
PLEASE READ BEFORE USING PLAYBLOX
MOVABLE PLAY EQUIPMENT FOR
SUPERVISED EARLY CHILDHOOD

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
PLAYBLOX
Thank you for purchasing PlayBlox. This booklet has been created to provide important information when setting
up and using PlayBlox.
PlayBlox is designed and built to the NZS5825:2015 + Appendix A ECE Playground Safety Standards.
To get the most out of your PlayBlox we recommend you read through this guidelines booklet and also refer
to the Playground Equipment and Surfacing handbook - SNZ HB 5828.2:2006. You can download this from
Standards New Zealand website.
PlayBlox equipment is movable and be configured in dierent ways, it is important to observe some basic rules
and common sense to ensure compliance and safe play.
CONTENTS
1.0
2.0
3.0
3.1
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
5.0
5.1
5.2
GENERAL INFORMATION
SAFETY SURFACING
CLIP SYSTEM
OTHER ATTACHMENTS
BLOX
SLIDES
STEPS
OVERHEADS
CLIMBERS - SMALL
CLIMBERS - LARGE
TODDLER BRIDGE
BRIDGES
BRIDGES - HANDRAILS
BRIDGES - ENCLOSED
BALANCE BEAMS
INSPECTIONS
MAINTENANCE
WARRANTY
PAGE 3
PAGE 4
PAGE 5
PAGE 6
PAGE 7
PAGE 8
PAGE 9
PAGE 9
PAGE 9
PAGE 10
PAGE 10
PAGE 10
PAGE 11
PAGE 11
PAGE 12
PAGE 13
PAGE 14
PAGE 14
1 2

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
WET POUR RUBBER
3 4
1.0 - GENERAL INFORMATION 2.0 - SAFETY SURFACING
The NZS:5828:2015 states: “A minimum fall zone of 1500mm shall apply
for movable play equipment items that measure more than 600mm from
surface level.
Movable playground equipment with a free height of fall over 600mm shall
have a certified impact attenuating surface.
The surfacing used beneath playground equipment having a free height
of fall not exceeding 600 mm, should have some impact attenuating
properties.”
Park Supplies recommends all PlayBlox items are set up on impact
attenuation safety surfacing that has a 1500mm CFH and a minimum fall
zone of 1500mm around all items.
Big Blox
1150mm high
Middle Blox
800mm high
1.5m fall zone REQUIRED. Safety Surfacing with
impact attenuation
1.5m CFH REQUIRED.
Safety Surfacing with
impact attenuation 1.5m
CFH RECOMMENDED.
1.5m fall zone
RECOMMENDED.
The definition of movable playground equipment is a range of equipment
that is not permanently fixed in place, and can be moved on a regular basis
to extend play opportunities.
Movable playground equipment shall be used only under supervision.
When not in use, movable playground equipment shall not be accessible.
Movable playground equipment shall have attachments that connect
securely and are unable to move or slip out while in use.
When setting up play experiences using movable playground
equipment, the supervisor shall ensure that the equipment is placed in
such a way as to prevent the equipment tipping or falling while in use and
to prevent entrapment. (NZS:5828:2015 Appendix A)
All attachments should be checked by an adult supervisor daily. Care must
be taken to ensure all four connection points are fixed on all attachable
items.
For Fall Zones, a safe rule of thumb is to have a minimum of 1.5m of free
space around all movable play equipment.
PlayBlox is manufactured in New Zealand by Park Supplies Playgrounds.
We can also provide maintenance and repairs if the need arises - see page
14 for more detail.
You can see the full range of early childhood play equipment that Park
Supplies produce at www.parksupplies.co.nz
If you have any queries on how to setup and use PlayBlox please visit our
website please call us on 0800 752 947. RUBBER MATTING tiles provide a great aesthetic
finish to your play area, there are many colour and
style options available. Tiles have the added benefit of
being replaceable should vandalism occur.
LOOSE-FILL is a great surface for protection from
falls. If using a loose-fill surface extra care will need to
be given to setting up movable equipment to insure it
is stable.
SYNTHETIC TURF provides a great grass look to
your play area. There are various grass pile height
options and colours to choose from.
Contact us for a free no-obligation quote on the surface of your choice.SURFACE OPTIONS AVAILABLE:
WET POUR RUBBER provides a
unique finish to your play area. Combining multiple
colours, curves and shapes you can create a visually
dynamic surface.
LOOSE-FILLRUBBER MATTINGSYNTHETIC TURF
Stage Blox &
Little Blox
450mm high

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
5
3.1 - OTHER ATTACHMENTS
You can attach PlayBlox items to other manufacturers movable boxes
using our unique adaptors (sold separately).
TO USE:
1. Choose the correct adaptor for your situation, please contact us to
discuss the correct adaptor for your needs.
2. Remove any attachments from box.
3. Clip adaptor on by pushing clips through and down into box slots.
4. Attach climbers, bridges etc to slots in adaptor front, making sure to
attach securely.
Adaptors and attachments should be checked by a supervisor daily.
6
3.0 - CLIPS
1 2 3
4 5 6
Our clipping system is designed to be used by adult supervisors only. It is deliberately designed to be to dicult
for children to position and correctly slot clips into boxes.
Incorrect installation of attachment to boxes may result in injury to the user.
The PlayBlox range has a unique, easy to use clipping system, providing countless reconfigurable opportunities.
Using our exclusive Blox and adding additional climbers, overheads, bridges, slides and balance activities you can
create endless play experiences.
CLIMBERS, LADDERS, BRIDGES, BALANCE BEAM WITH ROTATING CLIPS:
Make sure clips are facing the correct way (image one).
1. Hold clips on side of activity so they are pointing toward the holes in the Blox.
2. Insert thin part of clip into the hole and rotate clip so slot is vertical (image 2).
3. Push clip down so slot is all the way down in hole in Blox (image 3).
4. Repeat at the other end to join two Blox.
BRIDGES, SLIDES, OVERHEADS WITH NON-ROTATING CLIPS:
Must be set up between two of the same type (height) Blox.
1. Line up clips with holes in first Blox, making sure the item is square to the face of the Blox you are attaching
it to (image four).
2. Push clips though holes in Blox (image five).
3. Push item down so the clips slots slide down into place and the top of the clip sits on the top of the Blox
(image five).
4. Hold the item in place and have another supervisor slide the second Blox into the clip at the other end and
push down to secure.
The clip system is designed so to not come loose during use, if installed correctly.
Adaptors and attachments should be checked by a supervisor daily.

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
7
4.0 - BLOX
PlayBlox come in four sizes:
BIG BLOX (PB04)
1150mm high x 800mm x 800mm
MIDDLE BLOX (PB03)
800mm high x 800mm x 800mm
STAGE BLOX (PB02)
450mm high x 800mm x 800mm
LITTLE BLOX (PB01)
450mm high x 450mm x 450mm
Blox are designed to be moved/
arranged by adult supervisors only.
To arrange the configurations it is
recommended that two or more
people work together to make
it easier.
Follow the instructions on the
following pages to attach play
activities to the Blox to create your
own play experiences.
BIG BLOX MIDDLE BLOX
STAGE BLOX LITTLE BLOX
Slides include Big Slide (PB53), Middle Slide (PB52), Stage Ramp (PB51) and Little Slide (PB50).
Slides are designed to only attach to one height, ie the Big Slide only fits the Big Blox and will not attach to the
other sized Blox.
Attaching slides:
• Choose an area which is level. An unlevel surface can cause a slide to move during use.
• Line up clips with holes in Blox, making sure the slide is square to the face of the Blox you are attaching to.
• Push clips though holes in Blox.
• Push slide down so the clips slide down into place and the top of the slide sits on the top of the Blox.
• For Stage Ramp and Little Slide - Ensure a fall-zone of at least 1m at end of slide.
• For Big Slide and Middle Slide - Ensure a fall-zone of at least 1.5m at end of slide.
Attachments should be checked by a supervisor daily.
8
4.1 - SLIDES
MIDDLE SLIDEBIG SLIDE
STAGE RAMP LITTLE SLIDE

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
9
4.2 - STEPS
4.3 - OVERHEADS
4.4 - CLIMBERS - SMALL
Steps include Thin Step (PB18) and Wide Step (PB19) and are to be used
on the Stage Blox or Little Blox ONLY.
• Clip on steps are to be used on Stage Blox and Little Blox ONLY.
• They are designed to help younger children to climb onto these
lower Blox.
• Available in two widths - note the wider one will only fit the Stage
Blox and not the Little Blox.
• Put clips though holes in Blox and push down.
• Steps should have a minimum fall zone of 1m.
Attachments should be checked by a supervisor daily.
Overhead items (Overhead Ladder (PB60) and Gladiator Rings (PB61)) are
to be used on the Big Blox or Middle Blox ONLY.
• Must be set up between two of the same type (height) Blox.
• When installing, you will need to attach one end to the first Blox and
then slide the second Blox into the clip at the other end and push
down to secure.
• The clip system is designed so the overhead cannot come loose
during use, if installed correctly.
• Overheads need a fall zone of 1.5m either side.
Attachments should be checked by a supervisor daily.
Small climbers include Rock wall (PB12), Rope Net (PB14), Spiders Web
(PB16) and Ladder (PB10).
• These are designed to be used on Middle Blox, Stage Blox and Little
Blox (Ladder only).
• Attach clips into Blox and rest steel end on the ground.
• Small climbers need a minimum fall zone of 1.5m when attached to
Middle Blox and 1m when attached to Stage Blox.
NOT to be used between two Blox as a climber or bridge.
Attachments should be checked by a supervisor daily. 10
4.5 - CLIMBERS - LARGE
4.6 - TODDLER BRIDGE
4.7 - BRIDGES
Large climbers include Rock wall (PB13), Rope Net (PB15), Spiders Web
(PB17) and Ladder (PB11).
• These are designed to be used on all Blox sizes.
• Attach clips into Blox and rest steel end on the ground.
• Large climbers need a minimum fall zone of 1.5m when attached to
Big Blox or Middle Blox and 1m when attached to Stage Blox.
NOT to be used between two Blox as a climber or bridge.
Attachments should be checked by a supervisor daily.
Toddler Bridges include Toddler Bridge Thin (PB30) and Toddler Bridge
Wide (PB31).
• Must be set up between two of the same height Blox.
• When installing, you will need to attach one end to the first Blox and
then slide the second Blox into the clip at the other end and push
down to secure.
• Not recommended to be used on Big Blox.
Attachments should be checked by a supervisor daily.
Basic Bridges include Ladder Bridge (PB38), Rope Ladder (PB35) and
Plank Bridge (PB32).
• Can be used between any height Blox.
• Can be used between a Blox and the ground as a ladder.
• It is important that the clips at both ends are installed correctly to
ensure they can not move while in use.
• Maximum of 3 users at any one time.
• Bridges are 1.5m in length and 315mm wide.
• Minimum fall zone of 1.5m when attached to Big Blox or Middle Blox
and 1m when attached to Stage Blox or Little Blox.
Attachments should be checked by a supervisor daily.

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
11
4.8 - BRIDGES - HANDRAILS
4.9 - BRIDGES - ENCLOSED
Bridges with handrails include Ladder Bridge with Handrails (PB39), Rope
Ladder with Handrails (PB36) and Plank Bridge with Handrails (PB33).
• Can be used between any height Blox.
• Can be used between a Blox and the ground as a ladder.
• It is important that the clips at both ends are installed correctly to
insure they can not move while in use.
• Maximum of 3 users at any one time.
• Bridges are 1.5m in length and 315mm wide.
• Minimum fall zone of 1.5m when attached to Big Blox or Middle Blox
and 1m when attached to Stage Blox or Little Blox.
• Its is important that children are not allowed to climb on top of the
handrails as this could cause the bridge to tilt or come loose.
Attachments should be checked by a supervisor daily.
Bridges with Enclosed sides include Ladder Bridge with Enclosed sides
(PB40), Rope Ladder with Enclosed sides (PB37) and Plank Bridge with
Enclosed sides (PB34).
• Must be set up between two of the same height Blox.
• It is important that the clips at both ends are installed correctly to
ensure they can not move while in use.
• Maximum of 3 users at any one time.
• Bridges are 1.5m in length and 315mm wide.
• Minimum fall zone of 1.5m when attached to Big Blox or Middle Blox
and 1m when attached to Stage Blox or Little Blox.
• Its is important that children are not allowed to climb on top of the
sides as this could cause the bridge to tilt or come loose.
Attachments should be checked by a supervisor daily.
4.10 - BALANCE BEAM
• To be used on Middle Blox, Stage Blox or Little Blox.
• Must be set up between two of the same height Blox or between
Ground and Stage Blox or Little Blox.
• Minimum fall zone of 1.5m when attached to Big Blox or Middle Blox
and 1m when attached to Stage Blox or Little Blox.
• NOT to be used on Big Blox.
Attachments should be checked by a supervisor daily.
12

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ 0800 752 947
5.0 - INSPECTION 5.1 - MAINTENANCE
5.2 - WARRANTY
It is the responsibility of the owner/manager to ensure regular inspections and maintenance of all playground
equipment and safety surfacing. The minimum frequency is as listed. The frequency may need to be increased if
the equipment is subject to heavy use, vandalism or harsh conditions.
DAILY INSPECTION:
• Check all Blox are set up on a stable, level surface to prevent tipping or falling when in use.
• Check all clips are in good condition.
• Check all Clips are attached correctly and securely so they are unable to move or slip out during use.
• Ensure all equipment is within safety surface area.
• Ensure all minimum fall-zones are correct. A safe rule of thumb for fall-zones is to have a minimum of 1.5m
of free space around all movable play equipment. (This should be on a certified impact attenuation surface if
the equipment is over 600mm free height of fall.)
• Check items for any wear and tear which may need repairing.
Important to check all clips on activities, all rope work for any wear or loose fiber etc. Check for any loose or
missing bolts in Blox or activities. Check rock holds are secure.
WEEKLY/MONTHLY INSPECTION:
• Conduct a daily inspection as above.
• Wipe down any soiled surfaces with a soap and water.
• Check safety surface.
If surface is loose fill (woodchip, bark etc.) check the depth is 300mm and is free from rubbish or foreign
objects (rocks, stones, glass etc.).
Check loose fill area edging for splintering, cracking or loose nails or screws.
For synthetic surfaces check for wear and tear and insure no loose or damaged areas which cause a trip
hazard. Check for foreign objects.
ANNUAL INSPECTION (OF THE ENTIRE PLAY AREA INCLUDING MOVABLE ITEMS):
An annual playground inspection should be conducted by an accredited RPII Level 3 Playground Inspector.
Their report should include:
Annual main inspection, Structural stability, General safety hazards, Risk and recommendations, Inspection of play
equipment, Inspection of play safety surface, Wear and tear, Compliance audit to NZS:5828;2015, and Entrapment
check using probes.
Please contact us on 0800 752 947 if you need any maintenence or
repairs to your PlayBlox equipment.
We warrant all our products to be free from defects (in material and workmanship only) for a period of 5 years,
applied from date of original invoice. If you discover a defect in a product or service covered by this warranty, the
purchaser must advise Park Supplies Ltd in writing of the defect. At our discretion we will repair or replace using
new or refurbished components.
CONDITIONS OF WARRANTY:
The warranty does not cover parts that are subject to normal wear and tear, weathering and replacement
requirements, nor does it cover acts of damage, vandalism, misuse, neglect, accident, or if altered in any way or
added to other than by Park Supplies Ltd.
The warranty does not include damage caused by neglect where the onset of a defect should have been
identified ed through the implementation of a regular inspection and/or maintenance programme as per our
guidelines booklet. This includes, self operational inspections using the inspection guidelines on page 13 and an
Annual Level 3 Inspection from a recognized and certified RPII inspector.
The warranty excludes weathering; be it warping, twisting, cracking, splitting or blemishing of timber or plastic
components.
The warranty does not cover cosmetic items such as scratches, dents, marring, fading, weather, abnormal climate
conditions, rust or redecorations.
The warranty excludes freight, travel or installation of the warranty repaired or replaced item.
Eective date: 24/04/2019
13 14

PLAYBLOX.CO.NZ PARKSUPPLIES.CO.NZ
0800 752 947
PLAYBLOX.CO.NZ
V1 MAY 2019WWW.PARKSUPPLIES.CO.NZ
PLAYBLOX IS PROUDLY NEW ZEALAND MADE BY
MOVABLE PLAY EQUIPMENT FOR
SUPERVISED EARLY CHILDHOOD