PDR Mounts PDM 625T-8 User manual

Model
Thank you for purchasing thePDR panel display wall mount.
To ensure the correct usage, please read and follow the instructions
manual thoroughly. Please store the instructions in a safe place for future reference.
Features
1
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship.
We are not liable for improper installation that results in damage to mounts, adapters or presentation equipment.
Mounts by
A division of David Engineering & Mfg. Inc.
PDM 625T-8 PANEL DISPLAY MOUNT
Low profile 2 5/8”
16”, 24” or 32” stud mounting
Easy installation
Flat to 13 deg tilt
Lateral movement from center for better viewing position
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the
weight of both the display and the mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Special techniques are necessary for installation of the panel display mount.
?Do not attempt to perform this work by yourself.
?Request an installation specialist to install this unit.
?Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
?Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for the mounting
unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat and airflow.

the strength of the wood studs is not sufficient, add reinforcement.
Always confirm the center of the stud is used for the installation.
Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any
not install in locations where there are excessive amounts of dust,
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation..
The internal temperature could elevate and possibly result in fire. Install the panel (4") or more away from surroundings.
sloped surfaces. Also, do not install facing upward. The internal temperature could
elevate and possibly result in fire. Injury or damage could also result from falling.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the panel display
light. Strong light could result in eye fatigue during usage.
Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the panel
could result with injury due to the panel display falling.
Make sure that both hooks from the each pivot bracket engage with the wall bracket . Failure to do so could cause the panel
Always use at least two people to perform the installation work. Injury could result from dropping heavy objects.
be installed must be capable of long-term support of the total load of
so be taken to ensure sufficient strength to
bration and other external forces.
anel display to fall and cause injury.
anel display + wall mount)
C a u t i o n : I n s t a l l a t i o n o f u n i t i s t o b e c a r r i e d o u t b y q u a l i f i e d t e c h n i c i a n s o n l y . I n s t a l l i n a n a p p r o p r i a t e
l o c a t i o n b y c h e c k i n g t h e w a l l s t r u c t u r e a n d d u r a b i l i t y f o r s a f e t y a n d a c c i d e n t p r e v e n t i o n .
INSTALLATION LOCATION
INSTALLATION ON A WOODEN WALL
Always install so that the load is supported by a wood stud. If
Do not install on decorative posts or plaster board.
water is possible. These can result in fire or electric shock.
Do not install close to an air conditioner intake or outlet. Do
oily smoke or tobacco smoke. Fire could result.
.
Install only on a vertical surface. Avoid
falling.
Do not install where there is direct sunlight or other strong
display falls.
Do not alter any of the parts. Do not use broken parts. This
display to fall.
The wall where the wall mount is to
the panel display and wall mount. Measures should al
withstand the force of earthquakes, vi
Note: Incorrect installation can cause the p
Total load of the panel (p
CAUTION
WARNING
WARNING
Rev 021908
MAXIMUM WEIGHT 300 LBS (138 kg)
2

Product specification
3.94”
100mm 3.94”
100mm
24.61”
625mm
4.00”
7.71”
5.39”
847mm
33.35” MAX
25.50”
36.00”
2.64”
13°
3

Wall mount bracket…1 pc
A
B
D
E
Display bracket .... 2 pcs
GL
FK
C
HM
J
Locking bar... 2 pc
I
5mm x 16mm...4 pcs
Multi mount washer ...4 pcs
Plastic spacer 3/4 x 1”...4 pcs
5mm x 40mm... 4 pcs
6mm x 16mm...4 pcs 6mm x 40mm...4pcs
8mm x 16mm...4pcs 8mm x 40mm...4pcs
5/16” Flat washers...6 pcs
5/16’ x 2 ½”Lag bolts...6 pcs
MOUNTING ARM ASSEMBLY
PARTS LIST
Fig 1
LEFT HAND SHOWN RIGHT HAND OPPOSITE
TOP
BOTTOM
4

1. FASTEN MOUNTING PLATE TO WALL
Fig 2
2. SECURE THE DISPLAY BRACKETS TO THE MONITOR
The bracket must be secured to the wall studs capable of at least (4) times the weight of the unit. The wall bracket should be mounted at the same horizontal center line
as the display center line ( viewing horizontal center line). Using the six lag bolts ( E ) and washers supplied ( D ), level and secure the mounting plate to the center of
the wall studs. Pre drill 3/16” (5mm) hole for lag bolts
FLOOR LINE
VIEWING
HORIZONTAL
CENTER LINE
Fig 3
Mounting hardware F,G,H,K,L,M
Square Multi-mount washer (J)
Panel display bottom edge
Display bracket ( A ) left
Plastic spacer ( I )
Display bracket ( A ) right
5
Lay the display panel face down on a protected surface.
Position the left and right hand bracket (A) with the holes facing towards the bottom.
See Fig. 3 Note bottom edge.
Using the proper screws (F,G,H) and multi washer (J) supplied position the brackets equal distance from the top and bottom edge ,
and tighten hardware.
Additional hardware is supplied (screws K,L,M) and plastic spacers (I) to be used if needed for different display mounting
applications.
Note: Do not over tighten the bracket mounting screws as damage to the displays internal mounting threads could occur.
. See Fig 2
WOOD STUDS
(std construction 2 x 4 studs/1/2” wallboard)
32"
16"

3. MOUNT THE DISPLAY TO THE WALL MOUNT BRACKET
Fig 4 Fig 5
4. ADJUST LATERAL MOVEMENT AND TILT
Lateral Movement:
Fig 6 Fig 7
Locking bar (C)
Lift the display, with the brackets attached, onto the wall plate. See Fig 4
Position the top and bottom into the slots. See Fig 5 and 6
Make sure the display brackets engage the rails on the wall mount bracket (B) See Fig 5
Insert the locking bar (C) as shown in Fig 5 with the locking holes facing up to match the holes in the wall mount bracket (B) .
Secure with a padlock (not supplied) thru holes in the locking bar (C) and wall mount bracket (B) Fig 5
13°
6
Once the display on the wall is complete, you can still move the display left to right to optimize the final viewing position
by gently sliding the unit on the wall bracket. The adjustment distance will vary depending on the display size being
used. See Fig 7
Tilt adjustment:
Tilt adjustment can be made by holding the top of the display and loosening both tri knobs.
After tilt adjustment is complete, tighten both tri knobs. See Fig 6
Tri knob