Petit SEAL Play House Grande 2003 Instruction manual

- IMPORTANT NOTICE -
RESIDENTIAL HOME USE ONLY. Not intended for public areas
such as schools, churches,nurseries, day cares or parks
603
Partsmissing or damaged?
Need assistance withassembly?
Contact Us First!
Please send your request to our central customer
service email: [email protected]
One of our customer service agents will reply to
you within 24 hours

603
REV: 3-13-2022
Assembly and Installation Instructions
Intended for children from ages 3 to
10
Play House Grande
RESIDENTIAL HOME USE ONLY.
(BOX: 1004)
Swiss Walterli Kft.
Petit Seal
Simonffy utca 4-6, fszt. 41.
4025 Debrecen, Hungary
[email protected] www.petitseal.com
Do not use this playset
until competely assembled
and inspected by an adult.
WARNING: ASSEMBLY
BY AN ADULT RETAIN
THESE INSTRUCTIONS
Model: 2003
Not intended for public areas such as schools, churches, nurseries, day cares or parks

CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have
occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety
standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious
or fatal injury to children using this play system. Go over the warnings and safe play instructions regularly with your
children and make certain that they understand and follow them. Remember on-site adult supervision is required
for children of all ages.
Do not allow children to wear open toe or heel footwear
like sandals, flip-flops or clogs.
Do not allow children to walk, in front, between, behind
or close to moving rides.
Do not let children twist swing chains or ropes or loop
them over the top support bar. This may reduce the
strength of the chain or rope and cause premature
failure.
Do not let children get off rides while they are in motion.
Do not permit climbing on equipment when it is wet.
Do not permit rough play or use of equipment in a
manner for which it was not intended. Standing on or
jumping from the roof, elevated platforms, swings,
climbers, ladders or slide can be dangerous.
Do not allow children to swing empty rides or seats.
Do not allow children to go down slide head first or run
up slide.
Warnings and Safe Play Instructions
STRANGULATION HAZARD
• NEVER allow children to play with ropes, clotheslines,
pet leashes, cables, chains or cord-like items when
using this play-set or to attach these items to play-set.
• NEVER allow children to wear loose fitting clothing,
ponchos, hoods, scarves, capes, necklaces, items with
draw-strings, cords or ties when using this play-set.
• NEVER allow children to wear bike or sport helmets
when using this play-set.
Failure to prohibit these items, even helmets with chin
straps, increases the risk of serious injury and death to
children from entanglement and strangulation.
TIP OVER HAZARD
Choose a level location for the equipment. This can
reduce the likelihood of the play set tipping over and
loose-fill surfacing materials washing away during
heavy rains.
DO NOT allow children to play on the play-set until the
assembly is complete and the unit is properly
anchored.
Never add extra length to chain or rope. The chains or
ropes provided are the maximum length designed for
the swinging element(s).
Observe capacity limitations of your play-set.
Dress children with well fitting and full foot enclosing
footwear.
Teach children to sit with their full weight in the center of
the swing seat to prevent erratic swing motion or falling off.
Check for splintered, broken or cracked wood; missing,
loose, or sharp edged hardware. Replace, tighten and or
sand smooth as required prior to playing.
Verify that suspended climbing ropes, rope ladders, chain
or cable are secured at both ends and cannot be looped
back on itself as to create an entanglement hazard.
On sunny and or hot days, check the slide and other
plastic rides to assure that they are not very hot as to
cause burns. Cool hot slide and rides with water and wipe
dry prior to using.
Orientate slide such that it gets the least amount of
exposure to the sun.
SERIOUS HEAD INJURY HAZARD
Installation over concrete, asphalt, dirt, grass, carpet
and other hard surface creates a risk of serious injury
or death from falls to the ground. Install and maintain
shock absorbing material under and around play-set
as recommended on the Playground Surfacing
material page of these instructions.
COLLISION HAZARD
Place play-set on level ground at least 6 feet - 1.8m
from any obstruction such as a garage or house,
fences, poles, trees, sidewalks, walls, landscape
timbers, rocks, pavement, planters, garden borders,
overhanging branches, laundry lines, and electrical
wires. See OBSTACLE FREE SAFETY ZONE
CHOKING HAZARD/SHARP EDGES & POINTS
Adult assembly required. This product contains
small parts and parts with sharp edges and points.
Keep parts away from children until fully assembled.
WARNING LABEL
Owners shall be responsible for maintaining the
legibility of the warning labels.
Warning - Safe Play Instructions
Anchoring Playset
This playset must be anchored to the ground. Anchors are sold separately. A minimum of four anchors is required -
one anchor for each corner. Anchors should be installed at an angle to provide the best stability during use. Anchors
should be installed at or below the level of the play surfacing to prevent tripping or injuries resulting from a fall.
For sandy soil conditions, use an auger or twist style anchor.

GROUND STAKES (ANCHORS):
Check for looseness, damage or deterioration. Should firmly
anchor unit to ground during use. Re-secure and or replace, if
necessary.
PROTECTIVE COVERINGS:
Check all protective coverings on bolts, pipes, edges, and
corners. Replace if they are loose, cracked, or missing.
SWINGS, ROPES AND RIDES:
Reinstall if removed during cold season. Check all moving
parts including swing seats, ropes, chains and attachments for
wear, rust and other deterioration. Replace as needed.
Check that ropes are tight, secure at both ends and cannot
loop back as to create an entrapment.
WOOD PARTS:
Check all wood members for deterioration, structural damage
and splintering. Sand down splinters and replace deteriorated
wood members. As with all wood, some checking and small
cracks in grain is normal.
Applying a water repellent or stain (water-based) on a yearly
basis is important maintenance to maintain maximum life
and performance of the product.
Instructions for Proper Maintenance
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
SWINGS AND RIDES:
To prolong their life, remove swings and store inside when
outside temperature is below 32°F /0°C. Below freezing, plastic
parts may become more brittle.
SHOCK ABSORBING SURFACING:
Rake and check depth of loose fill protective surfacing
materials to prevent compaction and maintain appropriate
depth. Replace as necessary.
Your Petit Seal Playset is designed and constructed of quality materials with your child's safety in mind. As with all
outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play
Set, it is important that you, the owner, properly maintain it.
HARDWARE:
Inspect for tightness. Must be firmly against, but not crushing
the wood. DO NOT OVER-TIGHTEN. This will cause splintering
of wood.
Check for sharp edges or protruding screw threads. Add
washers if required.
SHOCK ABSORBING SURFACING:
Check for foreign objects. Rake and check depth of loose fill
protective surfacing materials to prevent compaction and
maintain appropriate depth. Replace as necessary.
HARDWARE:
Check metal parts for rust. If found,
sand and repaint using a non-lead paint
complying with 16 CFR 1303.
Inspect and tighten all hardware.
On wood assemblies DO NOT OVER
TIGHTEN as to cause crushing and
splintering of wood.
Check for sharp edges or protruding screw threads, add
washers if required.
Lubricate all metallic moving parts per manufacturer’s
instructions
PROTECTIVE COVERINGS:
Check all protective coverings on bolts, pipes, edges, and
corners. Replace if they are loose, cracked, or missing.
SWINGSAND RIDES:
Check swing seats, all ropes, chains and attachments for
fraying, wear, excessive corrosion or damage.
Replace if structurally damaged or deteriorated.
HARDWARE:
Lubricate all metallic moving parts per manufacturer's
instructions
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
Check at the end of the play season:
Check twice a monthduring play season:
Check once a monthduring play season:
If you dispose of your play set: Please disassemble and dispose of your unit so that it does not create any unreasonable
hazards at the time it is discarded. Be sure to follow your local waste ordinances.
Check the following atthe beginning of the play season:

Note: Do not install home playground equipment over concrete, asphalt, or any hard surface. A fall onto a hard surface can result in serious
injury to the equipment user. Grass and dirt are not considered protective surfacing because wear and environment factors can reduce
their shock absorbing effectiveness. Carpeting and thin mats are generally not adequate protective surfacing. Ground level equipment -
such as a sandbox, activity wall, playhouse or other equipment that has no elevated play surface - does not need any protective surfacing.
Section 4 of the consumer product safety commission’s outdoor home playground safety handbook₉
Playground Surfacing Materials
Select Protective Surfacing
Maintain a minimum depth of 9 inches [22,9 cm] of loose-fill materials such as wood mulch/chips, engineered wood fiber (EWF), or
shredded/recycled rubber mulch for equipment up to 8 feet [2,4 m] high; and 9 inches [22,9 cm] of sand or pea gravel for equipment up
to 5 feet high. NOTE: An initial fill level of 12 inches [30,5 cm]will compress to about a 9- inches [22,9 cm] depth of surfacing over time.
The surfacing will also compact, displace, and settle, and should be periodically refilled to maintain at least a 9- inch [22,9 cm] depth.
Use a minimum of 6 inches of protective surfacing for play equipment less than 4 feet in height. If maintained properly, this should be
adequate. (At depths less than 6 inches [15,2 cm], the protective material is too easily displaced or compacted.)
Use containment, such as digging out around the perimeter and/or lining the perimeter with landscape edging. Don’t forget to
account for water drainage.
Check and maintain the depth of the loose-fill surfacing material. To maintain the right amount of loose-fill materials, mark the correct
level on play equipment support posts. That way you can easily see when to replenish and/or redistribute the surfacing.
Do not install loose fill surfacing over hard surfaces such as concrete or asphalt.
Loose-Fill Materials:
One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-protective
surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for
the equipment height in accordance with ASTM Specification F 1292. There are different types of surfacing to choose from;
whichever product you select, follow these guidelines:
You may be interested in using surfacing other than loose-fill materials - like rubber tiles or poured-in-places surfaces.
Installations of these surfaces generally require a professional and are not “do-it-yourself” projects.
Review surface specifications before purchasing this type of surfacing. Ask the installer/manufacturer for a report showing that the
products has been tested to the following safety standard: ASTM F 1292 Standard Specification for Impact Attenuation of Surfacing
Materials within the Use Zone of Playground Equipment.This report should show the specific height for which the surface is intended
to protect against serious head injury. This height should be equal to or greater than the fall height - vertical distance between a
designated play surface (elevated surface for standing, sitting, or climbing) and the protective surfacing below - of your play equipment.
Check the protective surfacing frequently for wear.
Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles:
Proper placement and maintenance of protective surfacing is essential. Be sure to
Extend surfacing at least 6 feet [1,8 m] from the equipment in all directions.
For to-fro swings, extend protective surfacing in front of and behind the swing to a distance equal to twice the height of the top bar
from which the swing is suspended.
For tire swings, extend surfacing in a circle whose radius is equal to the height of the suspending chain or rope, plus 6 feet in all
directions.
This information has been extracted from the CPSC publications “Playground Surfacing-Technical information Guide” and “Handbook for Public Playground
Safety” Copies of these reports can be obtained by sending a postcard to the: Office of Public Affairs, U.S. Consumer Product Safety Commission, Washington,
D.C., 20207 or call the toll-free hotline: [phone]
Placement
Use Zone for Single-Axis Swings
Use Zone for Multi-Axis Swings
[1,8m] [1,8m]
[1,8m] [1,8m]
[1,8m]
[1,8m]
[1,8m]

Part Identification
On each page, you will find the
parts and quantities required to
complete the assembly step
illustrated on that page.
Throughout these instructions symbols are provided as important reminders for proper and safe assembly
Part Identification
Each part has the Part
Number printed on the end of
the part for ease of
identification.
Assembly Information
CAUTION - Protrusion Hazard
Symbols
Tools Required
Tape Measure
Carpenters Level
Carpenters Square
Claw Hammer
Standard or Cordless Drill
Rubber Mallet
#2 Robertson Drive Bit
(Included)
Ratchet with extension
7/16" (11mm) & 1/2" (13mm)
sockets
Open End Wrench
7/16" (11mm) & 1/2" (13mm)
Adjustable Wrench
Drill Bits (up to 3/8” (10mm)
sizes.
8’ (2.4m) Step Ladder
Safety Glasses
Adult Helpers
Pencil
This identifies infomation that
requires special attention.
Improper assembly could lead to
an unsafe or dangerous condition.
Check that assembly is square
before tightening bolts.
Check that set or assembly is
properly level before proceeding.
This indicates DO NOT over-drive
wood screws to avoid screw
protrusions.
This indicates time to tighten
bolts, but not too tight! Do not
crush the wood. This may create
splinters and cause structural
damage.
Use a measuring tape to assure
proper location.
Once the assembly is tightened, watch for exposed threads.
If a thread protrudes from the T-Nut, remove the bolt and
add washers to eliminate this condition. Extra washers have
been provided for this purpose.
Proper Hardware Assembly:
For bolts, tap T-Nut into hole with hammer.
Insert the hex bolt through lock washer first
then flat washer then hole.
Because the assemblies need to be squared
do not completely tighten until instructed.
To avoid injury or damage to the
assembly make sure to get help!
Use
Help
Measure
distance
Tighten
Bolts
Flush
Square
assembly
Use
Level
If Bolt protrudes
beyond T-Nut
Use an extra
flat washer
Hex Bolt
Lock
Washer
Flat
Washer T-Nut
(Hammer into place)
Do not crush wood!
Bolt Assembly
10
0

About ourwood
One of the main reasons for weathering is the effects of water (moisture); the moisture content of the wood at the
surface is different from the interior of the wood. As the climate changes, moisture moves in or out of the wood, causing
tension which can result in checking and or warping. You can expect the following due to weathering. These changes
will not affect the strength of the product:
At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water
absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, so we
recommend applying a water repellent or stain on a yearly basis (see your local stain and paint supplier for a recommended
product)
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you
are concerned that a part has experienced a severe weathering problem please call our consumer relations department for
further assistance.
What causes weathering? Does it affect the strengthof my Play System?
How can I reduce the amount of weathering to my Play System?
Petit Seal Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although
we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to
weathering which can change the appearance of your set.
Checkingis surface cracks in the wood along the grain. A post 4” x 4” (101mm x 101mm) will experience more checking
than a board 1” x 4” (25mm x 101mm) because the surface and the interior moisture content will vary more widely than
in thinner wood.
Warpingresults from any distortion (twisting, cupping) from the original plane of the board and often happens from
rapid wetting and drying of the wood.
Fadinghappens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.
1.
2.
3.
This space intentionally left blank

OCCUPANTS / WEIGHT LIMITS / TOTAL WEIGHT / FALL HEIGHT

WOOD IDENTIFICATION

WOOD IDENTIFICATION

HARDWARE LISTING
(Fasteners are shown in full size)

1. Layout parts and orient as shown.
2. Attach panels in the orders shown.
Parts Required:
157 X2
198 X1
199 X1
211 X1
216 X2
WALLS
1
WALLS
2
1. Layout parts and orient as shown.
2. Attach panels in the order shown.
Part 198
Part 199
Part 211
Part 157 X2
Part 216 X2
SCREWS FLUSH
Install panel
against groove
Parts Required:
157 X2 211 X1
198 X1 216 X2
199 X1
Panel is flush to end
of frame
Locate 216 centered on
holes and flush to 211
These (4) circled holes use
#8 x .75 Truss Head Screw X4
#8 x 1.00 Wood Screw X6
In all other holes
1 WALLS
70.00 [1778.0]
Maintain this measurement
at top and bottom of wall
during assembly
1. Layout parts and orient as shown.
2. Attach panels in the order shown.
Part 198
Part 199
Part 211
Part 157 X2
Part 216 X2
SCREWS FLUSH
Install panel
against groove
Parts Required:
157 X2 211 X1
198 X1 216 X2
199 X1
Panel is flush to end
of frame at ends
Locate 216 centered on
holes and flush to 211
These (4) circled holes use
#8 x .75 Truss Head Screw X4
#8 x 1.00 Wood Screw X6
In all other holes
1 WALLS
2
70.00 [1778.0]
Maintain this measurement
at top and bottom of wall
during assembly

WALLS
3
1. Locate panels on frames.
2. Attach panels as shown.
Part 161 X2
Part 183 X2
Part 184 X2
STEP 1 - Layout all parts as shown
Flush to panel
3 WALLS
4
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X19
Part 167 X2
Part 193
SCREWS FLUSH
Install panel
against groove
Parts Required:
161 X2 183 X2
167 X2 184 X2
193 X1
70.00 [1778]
Part 161 X2
Part 183 X2
Part 184 X2
STEP 1 - Layout all parts as shown
Flush to panel
3 WALLS
4
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X19
Part 167 X2
Part 193
SCREWS FLUSH
Install panel
against groove
167 X2 184 X2
193 X1
70.00 [1778]
WALLS
4
1. Locate panels on frames.
2. Attach panels as shown.
Parts Required:
161 X2
167 X2
193 X1
183 X2
184 X2

WALLS
5
1. Locate all panels on frames.
2. Attach panels as shown.
Part 161 X16
Part 193 X3
5 WALLS
6
Part 183
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X38
SCREWS FLUSH
Install panel
against groove
1.000 [25.4]
Do not use pre-drilled holes.
Insert screw 1.00 [25.4] above
hole to go into frame
Part 213
Under window
Part 215
Center on holes
and flush to 183
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X29
SCREWS FLUSH
These (3) holes use
#8 x .75 Truss Hd.
Screw X3
Part 161
Part 193
Panel flush to frame
Parts Required:
161 X17 213 X1
183 X1 215 X1
193 X4
70.00 [1778]
70.00 [1778]
1. Locate all panels on frames.
2. Attach panels as shown.
Part 161 X16
Part 193 X3
6
Part 183
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X38
SCREWS FLUSH
Install panel
against groove
1.000 [25.4]
Do not use pre-drilled holes.
Insert screw 1.00 [25.4] above
hole to go into frame
Part 213
Under window
Part 215
Center on holes
and flush to 183
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X29
SCREWS FLUSH
These (3) holes use
#8 x .75 Truss Hd.
Screw X3
Part 161
Part 193
Panel flush to frame
Parts Required:
161 X17 213 X1
183 X1 215 X1
193 X4
70.00 [1778]
70.00 [1778]
WALLS
6
1. Locate panels on frames.
2. Attach panels as shown.
Parts Required:
161 X17
183 X1
193 X4
213 X1
215 X1

WALLS
7
WALLS
8
1. Locate all panels onto frame before attaching
2. Attach panels as shown.
3. Carefully flip wall over.
Part 195
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X26
SCREWS FLUSH
Part 194 X7
Part 212
Panel and 212 flush
with end of frame at
both ends
Keep 215 centered
on holes
Part 305 Wall Plate
X4
.688 [17.5]
.688 [17.5] Locate plate as shown at
(3) locations and attach with
#8 x .75 Truss Hd. Screw X4
Center this plate
on seam
Carefully flip wall over
Parts Required:
194 X7 305 Plate X4
195 X1
212 X1
#8 x .75 Truss Hd. Screw X4
.63 [16.0] from edge, locate
evenly between screws installed
.63
[16.0]
REINFORCE TOP PANEL AND FRAME
1. Locate all panels onto frame before attaching
2. Attach panels as shown.
3. Carefully flip wall over.
Part 195
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X26
SCREWS FLUSH
Part 194 X7
Part 212
Panel and 212 flush
with end of frame at
both ends
Keep 215 centered
on holes
Part 305 Wall Plate
X4
.688 [17.5]
.688 [17.5] Locate plate as shown at
(3) locations and attach with
#8 x .75 Truss Hd. Screw X4
Center this plate
on seam
Carefully flip wall over
Parts Required:
194 X7 305 Plate X4
195 X1
212 X1
#8 x .75 Truss Hd. Screw X4
.63 [16.0] from edge, locate
evenly between screws installed
.63
[16.0]
REINFORCE TOP PANEL AND FRAME
1. Locate all panels onto frame before attaching.
2. Attach panels as shown.
3, Carefully flip wall over.
Parts Required:
194 X7
195 X1
212 X1
305 Plate X4
Flush
Flush

WALLS
9
WALLS
10
1. Layout parts and orient as shown.
2. Attach panels as shown.
Part 211
Part 198
Part 157 X2
Part 190
Part 214
Part 191 X8
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X28
SCREWS FLUSH
Keep part centered
on holes
Panel is flush to end of frame
Flush
Use #8 x .75" Truss Hd. Screw X4
at (4) circled holes in 198
Install panel
against groove
Parts Required:
157 X2 198 X1
190 X1 211 X1
191 X8 214 X1
70.00 [1778]
Maintain measurement
on wall
1. Layout parts and orient as shown.
2. Attach panels as shown.
Part 211
Part 198
Part 157 X2
Part 190
Part 214
Part 191 X8
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X28
SCREWS FLUSH
Keep part centered
on holes
Panel is flush to end of frame
at ends
Flush
Use #8 x .75" Truss Hd. Screw X4
at (4) circled holes in 198
Install panel
against groove
Parts Required:
157 X2 198 X1
190 X1 211 X1
191 X8 214 X1
70.00 [1778]
Maintain measurement
on wall
1. Layout parts and orient as shown.
2. Attach panels as shown
Parts Required:
157 X2
190 X1
191 X8
198 X1
211 X1
214 X1

WALLS
11
WALLS
12
1. Layout parts as shown.
2. Attach panels in the order shown.
Part 190 X2
Part 183
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X21
SCREWS FLUSH
Install panel
against groove
Part 212
Part 161
Part 192
Part 194
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X28
SCREWS FLUSH
Install panel
against groove
Part 194
X4
Part 212
Parts Required:
161 X6 192 X1
183 X1 194 X5
190 X2 212 X1
1. Layout parts as shown.
2. Attach panels in the order shown.
Part 190 X2
Part 183
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X21
SCREWS FLUSH
Install panel
against groove
Part 212
Part 161
Part 192
Part 194
With all parts flush to panel and frames
attach using #8 x 1.00" Wood Screw X28
SCREWS FLUSH
Install panel
against groove
Part 194
X4
Part 212
Parts Required:
161 X6 192 X1
183 X1 194 X5
190 X2 212 X1
1. Layout parts as shown.
2. Attach panels in the order shown.
Parts Required:
161 X6
183 X1
190 X2
192 X1
194 X5
212 X1

WALLS
13
1. Locate all panels onto frame before attaching.
2. Attach panels as shown.
3. Carefully flip wall over.
Parts Required:
305 Plage X4
.688 [17.5]
.688 [17.5]
Locate plate as shown at
(3) locations and attach with
#8 x .75 Truss Hd. Screw X4
Center this plate
on seam
#8 x .75 Truss Hd. Screw X4
.63 [16.0] from edge, locate
evenly between screws installed
.63
[16.0]
Carefully flip wall over
REINFORCE TOP PANEL AND FRAME
Flush
Flush
WALLS
14

WALLS
15
Part WALL 3
Part WALL 3
Part 307 X2
Center on seam
#8 x 3
4" Truss Head Screw
X8
Wall assemblies flush
ASSEMBLE (2) SIDEWALL ASSEMBLIES
1. Locate all panels onto frame before attaching.
2. Attach panels as shown.
3, Carefully flip wall over.
Parts Required:
194 X7
195 X1
212 X1
305 Plate X4
1. Locate wall assemblies as shown and attach using wall brackets.
2. Assemble (2) TWO sidewall assemblies the same.
Parts Required:
WALL 2 X2
WALL 3 X2
307 Wall Bracket X4
ASSEMBLE (2) SIDEWALL ASSEMBLIES