PLAYNETIC Eurotramp PLAY User manual

Manual instruction
Eurotramp PLAY

100mm
1. Position the strap underneath the middle of the
jumping bed.
2. Position bottom of the generator kit 100mm
above the ground.
3. Drill in the 4 self tapping screws.
8mm
4x
C C
D D
2 1
C C
D D
2 1
DEBURR AND BREAK SHARP EDGES
MATERIAL:
DO NOT SCALE DRAWING
TITLE:
SCALE:2:1
SHEET 1 OF 1
A4
WEIGHT:
SelfTap-Screw
DWG NO.
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
A A
B B
C C
D D
2
2
1
1
SOLIDWORKS Educational Product. For Instructional Use Only
DEBURR AND BREAK SHARP EDGES
MATERIAL:
DO NOT SCALE DRAWING
TITLE:
SCALE:2:1
SHEET 1 OF 1
A4
WEIGHT:
SelfTap-Screw
DWG NO.
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
A A
B B
C C
D D
2
2
1
1
SOLIDWORKS Educational Product. For Instructional Use Only
DEBURR AND BREAK SHARP EDGES
MATERIAL:
DO NOT SCALE DRAWING
TITLE:
SCALE:2:1
SHEET 1 OF 1
A4
WEIGHT:
SelfTap-Screw
DWG NO.
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
A A
B B
C C
D D
2
2
1
1
SOLIDWORKS Educational Product. For Instructional Use Only
DEBURR AND BREAK SHARP EDGES
MATERIAL:
DO NOT SCALE DRAWING
TITLE:
SCALE:2:1
SHEET 1 OF 1
A4
WEIGHT:
SelfTap-Screw
DWG NO.
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
A A
B B
C C
D D
2
2
1
1
SOLIDWORKS Educational Product. For Instructional Use Only
8mm
1. Position the bracket underneath the middle of the
jumping bed (exactly opposite the generator kit)
2. Position it as high as possible
3. Drill in the 2 self tapping screws.
2x
C C
D D
2 1
C C
D D
2 1
DEBURR AND BREAK SHARP EDGES
MATERIAL:
DO NOT SCALE DRAWING
TITLE:
SCALE:2:1
SHEET 1 OF 1
A4
WEIGHT:
SelfTap-Screw
DWG NO.
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
A A
B B
C C
D D
2
2
1
1
SOLIDWORKS Educational Product. For Instructional Use Only
DEBURR AND BREAK SHARP EDGES
MATERIAL:
DO NOT SCALE DRAWING
TITLE:
SCALE:2:1
SHEET 1 OF 1
A4
WEIGHT:
SelfTap-Screw
DWG NO.
UNLESS OTHERWISE SPECIFIEDDIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
A A
B B
C C
D D
2
2
1
1
SOLIDWORKS Educational Product. For Instructional Use Only

1.
2.
1. Pull the strap between the bracket
2. Push in the bolt
3. Fasten the nut
2X2 meter attachment point 1,5x1,5 meter attachment point
M8 13
4x Fasten the LED module with acable tie
underneath the jumping bed.
One in everycorner.
please place LEDs at least
For safetyreasons,
40cm from the edge of the jumping bed
>40cm

Plug in the LED- modules and play
Cables loose on the ground
We are pleased to remain at your disposal to answer any questions:
EurotrampTrampoline - Kurt Hack GmbH
Zeller Straße 17/1
73235 Weilheim, Germany
Tel. +49-7023 - 9495-0
Fax +497023 - 9495-10
E-Mail [email protected]
www.eurotramp.com
Playnetic
Loohorst 3
7207 BL Zutphen
The Netherlands
Tel. [phone]
E-Mail ser[email protected]
www.playnetic.nl