PrimeCables Cab-LE32D11 User manual

English
Français
.
LED TV
Televiseur DEL
USER MANUAL
MANUEL D UTILISATION
MODEL:Cab-LE32D11

TABLE OF CONTENTS
Instructions
39
Media
Media
TTS Function Operation

FCC Declaration or Conformity Compliance statement
(Part 15):
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation. The party responsible for
compliance to these rules is:
Shopper+ Inc.
2210 52e AVE, Lachine, Quebec, Canada, H8T2Y3
Ph:514-631-5216

Ins truction s
a tip-ov er and/or injury.

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
ANTENNALEADIN WIR E
ANTENNA
DIS CHAGRE UNIT
(NEC SECTIO N 810-2 0)
GROUNDING CONDUCTORS
(NEC SECTIO N 810-2 1)
GROUND CLAMPS
POWER SERVIC E GROUNDIN G
ELECTRODE SYSTEM
(NEC ART 250,R ARTH)
GROUND
CLAMP
ELEC TRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
26)
designed in such a way that it does not require a safety connection to electrical earth.
27) Correct disposal of this product. This marking indicates that this product should not
be disposed with other household waste. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources.
This equipment is a Class II or double insulated electrical appliance. It has been
Ins truction s

Warning: batteries(pack or batteries installed) should not be exposed to excessive heat
such as sunshine, fire or other heat sources.
Ins truction s

Ins truction s
have bright spots/pixels.

10cm
10cm
below
Ins truction s
Note: Drawing is a representative example only
operat e
To avoid damage to the TV, place the TV on a table, face down on a soft surface.
the

TV Buttons and Connections
AV input
External AV Signal Input and
Right/Left Audio Inputs.
AV Output
Right/Left Audio Outputs.
External AV Signal Output and
Component Input
Connect to a component output
connection on your external device.
HDMI Input(HDMI1,2,3)
Connect to a HDMI output
connection on your external device.
ANT 75/RF Connection
Connect to the antenna/cable TV
output of your device or wall plate.
VGA Input
Connect to your PC using a VGA
cable(not provided).
PC Audio Input
Connect to your PC Audio Out
using 1/8 line cord.
HEADPHONE JACK
Plug earphones into jack for private
listening. Overrides speakers.
USB Input
Connect to your USB device.
COAXIAL Output
Connect to your SPDIF device
Output
Audio Out Right/Left
Connect to your external device.
OPTICAL
Digital Audio Output.
Y Pb Pr
INPUT
VIDE O R L
OUTPUT
VIDE O R L
INPUT
OPTICAL
OUTPUT
RL
COAXIAL
HDMI
8
HEADPHONE

5V 0.5A

Install and Connect TV
TV ANT
FM ANT
TV signal output
Setup your TV
1.Put your TV in a place that can bear the
weight of the TV.
To avoid danger, please do not assemble
the TV near water or extreme heat(such
as a furnace, light source,or candle.)
Do not block the ventilation on the back
of the TV.
Connect signal source and power
2. Connect the antenna cable to the RF
connection on the back or side of the TV,
and/or the signal source HDMI cable to the
HDMI input(s) on the rear or side of TV. Plug
the TV into the wall power outlet (AC120 ~ 60Hz).
1
3
Turn on the TV
3.While in standby mode the power indication
light will be red.Press the power button on
the TV or remote control.The light will change
to green.
Note:
Picture for reference purposes only.
2
TV Stand/Feet Installation Instructions
1.Open the carton and remove the TV,
accessories, and the stand/feet.
2.To avoid damage to the TV, place on
a table, face down on a soft surface.
The stand/feet are attached to the
TV with the provided screws.
3.Ensure all stand/feet screws are tightened securely.
Do not overtighten.
Your TV will have either a Stand or Feet.
Assemble accordingly.
1
3
2
4

11
Connect an RF cable from the TV’s input called “RF-In” and to your TV Aerial socket.
Select Time
Press ▼ / ▲ button to select the time zone, daylight saving time and time format you want to.
Press / button on the remote control to adjust.
Press ▼ / ▲ button on the remote control to select go to next step and press ENTER/ button
to go.
Select TV Configuration

on the remote (Air/Cable).
on the remote

/ Power saving
Press ▼ / ▲ button to select among Picture Mode /Brightness/ Contrast / Color / Tint / Sharpness /
Advanced Settings. Color Temperature/
Power saving Lower power consumption.
. The shadow of the picture cannot be adjusted.

Return
Move Select

preferen ce.
W
Default is off.

button to select among Sleep Timer / Time Zone / Daylight Saving Time /
Time Form at / Auto Clock / Clock.
Pre ss ▼ / ▲
Pre ss to ente r. ENTER / ▼
Pre ss button to adjust.◄ / ►
ENU again or back to pare nt menu. Pre ss M

the default
Press ▼ / ▲ button to select among Menu Language / Transparent /
OSD Timeout / Closed Caption /Over Scan/ Input Label /Other settings /
Restore Default / Setup Wizard/Voice Guidance/Video Description.
Press to ente r. ENTER / ▼
Press butt on to adjust.◄ / ►
ENU again or back to parent menu. Press M
Return
Next
Move