Prowler Mid-Cut 72B27LDML User manual

OPERATORS
MANUAL
72B27LDML

Table of Contents
i
 WARNING:
THE ENGINE EXHAUST FROM THIS PRODUCT
CONTAINS CHEMICALS KNOWN IN THE STATE
OF CALIFORNIATO CAUSE CANCER, BIRTH
DEFECTS OR OTHER REPRODUCTIVE HARMS.
IMPORTANT:
A separate Engine Owner’s Manual is included with your owner’s packet which contains additional engine
information that will not be repeated in this manual. You are urged to read it before attempting any operation or
repair of the engine. Engine Owner’s Manual covers the engine manufactures warranty.
General InformatIon ...................................................................................................................a SectIon
72B27lDml Prowler InfomatIon.....................................................................................................a-1
72B27lDml Prowler reference Sheet..........................................................................................a-2
encore warranty InformatIon .........................................................................................................a-4
Safety PrecautIonS.....................................................................................................................B SectIon
Prowler oPeratIon .....................................................................................................................c SectIon
Before oPeratInG remIDerS .............................................................................................................c-1
aSSemBly InStructIonS......................................................................................................................c-1
control locatIon ............................................................................................................................c-1
StartInG enGIne ...............................................................................................................................c-1
StoPPInG enGIne...............................................................................................................................c-1
Safety Interlock SyStem .................................................................................................................c-2
correct tranSmISSIon oPeratIon .....................................................................................................c-2
mowInG SPeeD..................................................................................................................................c-2
maIntenance InformatIon .............................................................................................................D SectIon
ServIce locator chart ....................................................................................................................D-1
General Info....................................................................................................................................D-2
tIre PreSSure..................................................................................................................................D-2
luBrIcatIon ......................................................................................................................................D-2
Battery InformatIon.........................................................................................................................D-2
oIl anD fIlter ..................................................................................................................................D-3
DrIve aDjuStment.............................................................................................................................D-4
neutral aDjuStment.........................................................................................................................D-4
trackInG aDjuStment........................................................................................................................D-4
Belt aDjuStment...............................................................................................................................D-5
Deck levelInG aDjuStment................................................................................................................D-5
Brake aDjuStment ............................................................................................................................D-5
Deck cuttInG heIGht aDjuStment .....................................................................................................D-6
mower BlaDeS .................................................................................................................................D-6
electrIcal...................................................................................................................................e SectIon
wIre harneSS SchematIc..................................................................................................................e-1
noteS..........................................................................................................................................f SectIon
 WARNING:
For illustration clarity, some illustrations and
gures in this manual may show shields or guards
removed. Under NO circumstance should your
mower be operated without these devices in place.

General Information
A-1
This manual covers the following equipment
models:
72B27LDML
To the new owner
The purpose of this manual is to assist owners
and operators in maintaining and operating the
Encore Rider mower and deck. Please read it
carefully; information and instructions furnished
can help you achieve years of dependable service.
A separate Engine Owner’s Manual is included
with your owner’s packet which contains additional
engine information that will not be repeated in
this manual. You are urged to read it before
attempting any operation or repair of the engine.
The Engine Owner’s Manual covers the engine
manufactures warranty.
It is the owner’s responsibility to make certain
that the operator reads and understands this
manual and all decals before operating this
machine. It is also the owner’s responsibility to
make certain that the operator is a qualified and
physically able individual, properly trained in the
operation of this equipment. Local regulations may
restrict the age of the operator.
Using this manual
General operation, adjustment and maintenance
guidance is outlined for both the experienced
and novice Encore user. Operating conditions
vary considerably and cannot all be addressed
individually. Through experience, however,
operators should find no difficulty in developing
good operating skills suitable to most conditions.
Directions used in this manual, for example RIGHT
or LEFT, refer to directions when seated on the
mower facing forward unless otherwise stated.
Photographs and illustrations used were current
at the time of printing, but subsequent production
changes may cause your machine to vary slightly
in detail. ENCORE MFG. CO., INC. reserves
the right to redesign and change the machine as
deemed necessary, without notification.
Warranty Registration
The Delivery and Warranty Registration form
must be completed and signed to validate your
warranty protection. As the new equipment owner,
you are expected to see that the form is completed
and forwarded to ENCORE MFG. CO., INC. at
time of delivery.
IMPORTANT: Any unauthorized modification,
alteration, or use of non-approved attachments
voids the warranty and releases ENCORE
MFG. CO., INC. from any liability arising from
subsequent use of this equipment.
Model and Serial Number
Mower model and serial number are found on the
serial tag, located on the seat frame directly under
the seat plate.
These numbers are required on the Warranty
Registration form. They will also assure you of the
correct service parts when replacement becomes
necessary.
Parts and Service
Use original Encore replacement parts only.
These parts are available through your local
Encore dealer. To obtain prompt, efficient service,
always provide the following information when
ordering parts:
1. Correct part number and description
2. Correct model number
3. Correct serial number
All warranty repair and service must be
handled through an authorized Encore dealer.
Arrangements should be made through your local
service center.
For the location of your nearest dealer please
use the dealer search on our website: www.
seriousred.com or www.encoreequipment.com
 WARNING:
DO NOT allow children to operate the machine. DO
NOT allow any adult to operate the machine without
proper instruction.

General Information
A-2
Quick Reference Sheet
Engine Pulleys
26.5hp Briggs & Stratton Daihatsu diesel 582447-0219 483025 tensioner pulley-clutch
Blades 823351 tensioner pulley-pump belt
583287 25" offset blade 523329 tensioner pulley-blade drive belt
Belts 523507 pump pulley
583153 blade drive belt 583107 pulley-blade spindle
593219 pump drive belt 583162 stationary idler pulley-back
523374 clutch belt 373068 stationary idler pulley-front
Tires 583447 gearbox pulley
583055 wheel/tire assy 523507 pulley-power shaft
583059 drive tire (24x12x12) 583200 pump drive pulley
583058 rim w/ valvestem Front Caster Bearings
N/A knobby tire assy 363187 1" flange bearing
N/A knobby tire Brake
s
583487 bar lug tire (23x10.5x12) 583038 RH brake caliper
823220 front caster complete 583039 LH brake caliper
823339 tire (13x6.5x6 front caster) 583511 brake pad kit
823338 front rim w/ valvestem
Spindles Sea
t
583106 spindle assy comp. 583519 full suspension seat
583111 housing 583077 seat complete w/ tracks
363350 bearing 583089 seat cushion
583112 shaft 583090 back cushion
583113 brg. Spacer tube 593097 molded arm rest
Transmission
593211 wheel motor TL0280US080AAWM Seal Kit # 593217
593210 hydro pump H1A14A4021DDAAA Seal Kit # 59321
5
583166 gearbox (model 211)
583513 gasket/shim kit - gearbox
583512 shaft seal kit - gearbox
423361 hydro filter
PTO shaft Electrical Components
593064 complete shaft 593051 wire harness
583481 yoke tube N/A safety module
593075 yoke shaft 583276 engine wire harness
523414 1" yoke 583423 time delay module
823372 3/4" yoke 523042 relay
523415 cross bearing 423027 igniton switch
583271 1" power shaft (12.5") N/A starter relay
Engine Base 582165 523034 park brake switch
Throttle 593045 593041 neutral switch
Choke N/A 523031 PTO switch
Muffler Briggs & Stratton Daihatsu 523030 seat switch
Muffler Gaske
t
N/A 523283 hour meter
Clutch 583308 823194 alarm
Torque Specs
65 ft-lbs blade bolt
90 ft-lbs nut on top of spindle
50 ft-lbs clutch bolt
250-300 ft-lbs wheel motor axle nut
72B27LDML

ENCORE WARRANTY
A-3
WHAT IS COVERED BY THIS WARRANTY
This warranty extends to the original retail purchaser only and
commences on the date of original retail purchase:
1. Residential use: The warranty will be Three years from
the date of purchase against defects in workmanship and
materials for any Encore rider that is used for consumer
purpose. Normal residential use means use of product on
owners’ property only. (Doesn’t apply to Prowler Series)
2. Commercial use: The warranty will be Two year from the
date of purchase and 90 days for rental use against
defects in workmanship and materials for any Encore rider
that is used for commercial purpose.
3. If the Purchaser discovers within this warranty period a
defect in materials or workmanship:
Purchaser must promptly notify an Authorized Encore
Dealer and return the mower, including any defective
parts, to an Authorized Encore Service Dealer.
Encore Mfg. Co., Inc. will determine if material or
workmanship is defective and then either repair or
replace such parts.
Service calls and/or transportation expense of the
product to and from the authorized dealer, for warranty
work, will be paid by the owner of the product.
4. Encore Mfg. Co., Inc. provides a limited warranty for
90 days from the date of purchase against defects in
workmanship and materials for all parts, excluding normal
wear items such as batteries, tires, and belts.
5. The Deck Shell warranty is Ten years from the date of
purchase against defects in workmanship and materials
for any Encore rider that is used for consumer and
commercial use only.
6. NOTICE: Cutter housings, electrical components,
hydraulic components and electric-clutch must be returned
before warranty will be paid.
7. The engine warranty is covered by its respective
manufacturer. Please refer to the manufacture’s warranty
statement in the manufacture’s engine manual that is
included in the literature packet. Engine warranties
should be referred to the nearest authorized service
outlet of the engine manufacturer.
Encore Mfg. Co., Inc. reserves the right to change or improve
the design of any mower without assuming any obligation to
modify any mower previously manufactured.
WHO MUST PERFORM THE WARRANTY SERVICE
All warranty service will be performed by dealers authorized
by Encore Mfg. Co., Inc. Service calls and/or transportation
expense of the product to and from the authorized dealer,
for warranty work, will be paid by the owner of the product.
For warranty service you can contact an authorized dealer or
contact: Encore Mfg. Co., Inc.
PO Box 888
Beatrice, Nebraska 68310
1-800-267-4255
www.encoreequipment.com
www.seriousred.com
WHAT IS NOT COVERED BY THIS WARRANTY
Encore Mfg. Co., Inc. does not warranty:
Repairs made by unauthorized persons.
Damage caused by use of the Encore equipment for
purposes other than those for which it was designed





Damages caused by disasters such as re, ood, wind,
and lightening.
Damages caused by neglect, abuse, abnormal use,
improper or unreasonable use, accident, negligence or
misuse.
Repairs or replacement resulting from the use of
unauthorized parts, accessories or attachments.
Repairs or replacement as the result of any alterations
or modications, in the determination of Encore, which
adversely affects the operation, performance or durability
of the equipment.
Encore unit which has the serial number removed or made
illegible.
Depreciation or damage caused by normal wear, lack of
reasonable and proper maintenance or failure to follow the
products owner’s manual provided by Encore Mfg. Co.,
Inc.
Normal maintenance parts and service including, but not
limited to: lters, fuel, lubricants, tune-up parts, belts,
blades, blade sharpening, brake or steering adjustments.
Repairs necessary due to improper fuel, contaminates
in the fuel system, or failure to properly prepare the fuel
system prior to any period of non-use over three months.
LIMITATION OF REMEDIES
In no case shall Encore Mfg. Co., Inc. be liable for any special,
incidental, or consequential damages based upon breach of
warranty, breach of contract, negligence, strict liability in tort, or
any other legal theory.
Such damages include, but are not limited to
Loss of prots
Loss of savings or revenue
Loss of use of Encore mower or any associated equipment
Cost of capital
Cost of any substitute equipment, facilities, services, or
downtime
The claims of third parties including customers, and injury
to property
Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
OWNER’S RESPONSIBILITY
You must maintain your Encore Product following the
maintenance procedures described in your owner’s manual.
Such routine maintenance, whether performed by a dealer or
by you, is at your expense.
This machine, like any other powered equipment, is
potentially dangerous unless properly operated. Any operator
must be cautious and keep safety in mind at all times.
Any operator, prior to using the Encore equipment, should
thoroughly familiarize himself with the owner’s manual
regarding operation and safety of the machine, as well as all
safety warnings on the machine itself.
ENCORE MFG. CO., INC. CANNOT BE RESPONSIBLE
FOR THE WAY YOU OPERATE, OR THE CONDITIONS
IN WHICH YOU OPERATE THE MOWER. USE COMMON
SENSE AT ALL TIMES.
WARRANTY REGISTRATION
1. The Warranty registration form MUST be completed and
forwarded to Encore Mfg. Co., Inc. within fteen days
following date of purchase.
2. The date of purchase constitutes delivery.
Encore Mfg. Co., Inc. does not assume or authorize anyone to
assume for them any other obligation.
















ENCORE
B-1
Safety Precautions
Your mower is only as safe as the operator!
Operator carelessness or error may result in
serious bodily injury. Improper maintenance of
the machine may also result in injury. Please read
and follow these instructions on Safe Operation
and be certain that anyone using this mower
fully understands and follows these instructions.
Instructions are from ANSI Standard B17.4-2004.
1. Familiarize yourself with the controls and know
how to stop the rider and mower deck quickly.
2. Inspect your work area carefully. Remove
debris from the area to be cut. Keep all
bystanders away from the mowing area.
3. Avoid contact with moving parts. Keep
hands and feet clear of the mower deck.
4. Never direct the discharge of material toward
bystanders or allow anyone near the machine
while in operation.
5. The machine is not intended for highway or
street use. Never carry passengers!
6. Never tamper with safety devices or guards.
If a guard or safety device is damaged or
removed, replace it before operating the rider.
 WARNING:
DO NOT allow children to operate the machine. DO
NOT allow any adult to operate the machine without
proper instruction.
 CAUTION:
Never add fuel to the tank while the engine
is running or hot. ALWAYS WAIT at least
five minutes before refueling and REFUEL
WITH THE ENGINE OFF. KEEP FUEL AWAY
FROM SPARKS OR FLAMES. WIPE AWAY
any fuel spillage BEFORE starting unit. Never
ll the fuel tank indoors. Wipe up any spilled
gasoline. Gasoline is highly ammable - NO
SMOKING.
7. Handle gasoline carefully. Use an approved
gasoline container. Fill the fuel tank, to within
1” from the neck, with good quality unleaded
gasoline.
8. Seat must be occupied and drive levers must
be in the Neutral position and the Blade Clutch
must be disengaged before starting engine.
9. Operator must wear proper shoes and
clothing, which may include safety glasses
and ear protection.
10. Mow only during daylight hours or under very
good articial light.
11. The safety shield over the Grass Discharge
area must always be bolted in place and in the
DOWN position unless the Grass Catcher is
being used.
12. If a solid object has been hit by the blades
stop the machine and check for damage.
Repair or replace any damaged / broken part
prior to restarting the engine.
13. To avoid burns, DO NOT TOUCH the engine
or mufer immediately after operation or
during.
14. Disengage blades when transporting and
when crossing walks and gravel roads.
15. DO NOT mow close to drop-offs, deep ditches
or other hazards. DO NOT attempt to mow
slopes grater than 15°, Always mow across
the face of a slope NOT up and down.
16. Reduce speed and exercise extreme caution
on slopes and in sharp turns to prevent tipping
or loss of control. Be especially cautious when
changing direction on slopes.
17. The Encore Rider is NOT designed for towing.
18. Only factory approved Grass Collection
Systems are permitted.
19. Shut off fuel while storing or transporting. Do
Not store fuel near ames or drain indoors.

ENCORE
C-1
 CAUTION:
Always remove the key and set the parking brake when
leaving the machine unattended, even for just a few minutes.
PREVENT ACCIDENTS: Do not give children or
unauthorized persons an opportunity to operate this machine.
Starting Engine
The throttle control, ignition switch and choke control
are located between the motion control levers on the
front panel under the front of the seat.
Because of a built-in safety interlock system, your
machine will not start unless the seat is occupied.
TO START ENGINE: occupy seat, set park brake,
leave the motion control levers swung out, move
throttle control lever all the way to choke position. With
the throttle set in slow postition, turn the key to the
“ON” position and wait approximately 5 seconds for the
glow plugs to cycle (indicator light should be on while
plugs are preheating combustion chamber). When the
light goes out, turn the key to the “START” position to
engage starter, release the key when engine starts.
Ignition switch is spring loaded and will return to run
position automatically. Let the engine warm up for a
few minutes before applying load.
Stopping Engine
TO STOP ENGINE: move throttle lever to idle position
and turn ignition key to “OFF” position. If engine has
been working hard or is hot, allow engine to idle for
a short period of time before turning off key. This
practice will help cool engine before stopping.
IN CASE OF EMERGENCY engine may be stopped
by turning ignition key to “OFF” position.
Before Operating -
Reminders
Fill engine crankcase as per engine manufacturer’s
manual. ENGINE DOES NOT HAVE OIL IN
CRANKCASE FROM THE FACTORY. Add proper
fuel to fuel tank, open shut-off valve.
The battery is a gel-cell and will not require acid.
Before hooking up the ground wires make sure that
the engine has been lled to the proper level with oil.
If battery will not turn the engine over after hooking the
wires up it may require a charge for 15 to 20 minutes.
Assembly Instructions
1. Remove mower from the crate.Lay out all the
hardware and parts from the inner box:
Parts will consist of:
1 - seat
1 - bolt bag
1 - literature packet
2 - handles
2. Open bolt bag and lay out
1 - oil breather cap
4 - 5/16-18 X 1 1/4 bolt
4 - 5/16-18 whiz lock nut
4 - 5/16-18 nylock nut
4 - 5/16- std flat washers
3. Take (4) 5/16 std flat washers and (4) 5/16 nylock
nuts and bolt the seat into place. Slide the studs of
the seat though the seat plate and secure with one
flat washer and nylock nut on each of the 4 studs.
(Slide the seat all the way back onto seat tracks
in order to flip seat forward.) At this time you may
also connect the seat switch wires.
4. Using the (4) 5/16-18 X 1 1/4 bolts, bolt the
handles into place.Note: Handle mounts to the
outside of the
square control
block with whiz
locks located on
slotted or handle
side.
5. Place breather
cap on oil tank.
Note:The oil
tank is pre-filled
from the factory
with 20w50
oil and should
be visible in
the sight glass
located on the
back of the tank.
The correct level is mid-point in the sight glass.
Control Location
1. Ignition Key- On front
control panel
2. Engine Throttle- On front
control panel
3. Engine Choke – On front
control panel
4. Blade Switch – Right hand
console
5. Parking Brake – Left hand
console
6. Fuel Valve- On front panel
7. Indicator Lights (oil, alt
and temp) – Right hand
console.
8. Glow plugs and fuel lter
lights located on the left console.
9. Hour meter is located behind the seat on the left hand side
standing in front of the machine. (Not shown)
10. Serial Plate is located under the seat, on the inside of the right
side of the seat frame. (Not shown)
1.
2.
3.
7.
5.
8.
6.
4.
RIGHT
FUEL
TANK
LEFT
FUEL
TANK
FUEL
TANKS
OFF
FORWARD
NEUTRAL
REVERSE

ENCORE
C-2
Safety Interlock System
Your Encore Rider is equipped with a Safety
Interlock System that is designed to help prevent
possible serious injuries. Understanding and
maintaining this system is vital, for maximum safe
operation.
TO START ENGINE:
1.Blades (PTO) must be “OFF”.
2.Control levers in neutral
(swung out).
3.Park Brake “ON”.
4.Operator in seat.
THE ENGINE WILL KILL IF:
1.The operator leaves the seat with:
a.The control levers out of neutral
(swung in).
b. The blades on (PTO).
c. The park brake is “OFF”.
d. All the above.
2.The park brake is set before the
control levers are in neutral
(swung out).
Mowing Speed
The Encore Rider is designed to operate most
efciently at maximum blade speeds.
The running speed of the machine should allow the
mower blades to maintain this maximum speed while
mowing across turf. Use a slower ground speed for
cutting tall grass, grass which is heavy with moisture,
or when mowing uphill. If ground speed is too fast,
or blade speed is too slow, mowing will be uneven
because mower blades will not be able to lift grass into
cutting position as the mower passes.
Throttle control regulates speed of engine as
measured in RPM. This control SHOULD NOT be
used to control ground speed.
Correct Transmission
Operation To Go Forward
Or Reverse
The Encore Rider is equipped with a pump/wheel motor
unit for each wheel and are controlled with “Motion
Control Levers” , one for each wheel. See Figure 1
Forward Travel Pivot Turn Forward Travel
Right Turn Reverse Travel Right Turn Reverse Travel
N = Neutral or Stopped Travel
The further the levers are moved away from the neutral position, the faster the machine will travel.
To turn the mower LEFT or RIGHT, slow the speed of the wheel in the direction you want to turn.
To CHANGE DIRECTION, slowly move levers to neutral and move the lever forward in the direction of travel you want to go.
Direction of arrows indicate direction of machine travel.
N N
AS SETTING IN THE DRIVER’S SEAT
Push both levers
forward evenly Push one lever forward and other
lever pull back
Push left lever
forward more than
the right lever
Pull left lever back
more than right
lever
Pull back both
levers evenly
[ Return both levers evenly to the neutral position. ]
Figure 1

ENCORE
D-1
E. D. B.
B.
A.
C.
C.
F.
G.
LOCATED TO REAR
OF THE DECK
LOCATED UNDER THE ENGINE
TO THE REAR OF THE MACHINE
52-61" MID CUT
GEAR BOX
72" MID CUT
GEAR BOX
• SERVICE GEAR BOX EVERY 500 HOURS
• CHECK FOR LEAKS WEEKLY
• OIL: 80-90 GEAR LUBE
NOTES:
ConsultEngineManualforEngine
ManufacturesRecommendations
on Operation and Maintenance
Information.
MAINTENANCE DAILY FIRST
8 HR.
EVERY
25 HR.
EVERY
50 HR.
EVERY
100 HR.
EVERY
200 HR.
EVERY
300 HR.
CHECK AND AD ENGINE OIL 
CHECK FOR LOOSE OR LOST NUTS AND SCREWS 
CHECK FOR FUEL AND OIL LEAKAGE 
CHECK OR CLEAN AIR INTAKE SCREEN 
CLEAN AIR CLEANER FOAM ELEMENT  
CLEAN AIR CLEANER PAPER ELEMENT  
CLEAN DUST AND DIRT FROM CYLINDER AND
CYLINDER HEAD FINS 
TIGHTEN NUTS AND SCREWS 
CHANGE ENGINE OIL  
CLEAN AND REGAP SPARK PLUG 
CHANGE OIL FILTER 
REPLACE AIR CLEANER PAPER ELEMENT 
CLEAN COMBUSTION CHAMBER 
CHECK AND ADJUST VALVE CLEARANCE 
CLEAN AND LAP VALVE SEATING SURFACE 
: SERVICE MORE FREQUENTLY UNDER DUSTLY CONDITIONS
: HAVE AN AUTHORIZED ENGINE MFG DEALER PERFORM THESE SERVICES
GREASE FITTING LUBRICATION LIST
A. FOOT LIFT PIVOTS
1 PUMP / 100 HOURS E. BACK RAIL 1 PUMP / 40 HOURS
B. CASTER SUPPORT BEARING
5 PUMPS / 250 HOURS F. DRIVE SHAFT 1 PUMP / 40 HOURS
C. FRONT CASTER
2 PUMPS / 40 HOURS G. POWER SHAFT BEARINGS 1 PUMP / 250 HOURS
D. PIVOT JOINTS (LEFT & RIGHT
SIDE)
1 PUMP / 40 HOURS

ENCORE
D-2
Maintenance Info
1. Do not adjust mower or change attachments
unless the engine has been stopped and the key
has been removed.
2. Good maintenance, wiping up gasoline and oil
spills, will reduce potential re hazards.
3. To insure that the mower will remain in safe
operating condition, check and tighten all bolts,
nuts and screws. Especially make certain the
blade bolt/nuts are always tightened properly.
4. Never adjust governor on engine to a faster speed.
The engine manufacturer adjusts the engine RPM
to the proper setting.
5. Allow time for the engine to cool down prior to
storing mower. Do not storemower or gasoline
near any open ame or where gasoline fumes may
be ignited.
6. Always replace worn or broken parts with genuine
Encore repair parts purchased from an authorized
Encore dealer. Using anything other than Encore
repair parts may void all Encore factory warranties.
NOTES:
The Encore Rider is driven and steered by the rear
wheels.
REARTIRECIRCUMFERENCEDIRECTLYEFFECTS
THE TRACKING OF THE MACHINE.
If the machine will not drive in a straight line, check
air pressure and adjust accordingly.
Description of Maintenance Task Service Intervals
Blades - sharpen & securely fastened to 65 ft-lbs Every 10 hours
Check fuel level Daily
Discharge chute - securely in place & in lowest
position Daily
Verify safety start interlock system Daily
Visually inspect tires Daily
Visually inspect unit for loose hardware and/or
damaged parts Daily
Check battery connections Every 50 hours
Check tire pressure with a guage Every 50 hours
Check pump drive belt tension & condition Every 100 hours
Check blade drive belt tension & condition Every 100 hours
Check deck drive belt tension & condition Every 100 hours
Tighten lug nuts on wheels Every 100 hours
Check oil level in engine See Note A
Change engine oil & filter See Note A
Change fuel filter See Note A
Clean air intake screen See Note A
Clean cylinder / head fins See Note A
Clean foam element See Note A
Clean paper element See Note A
Replace air cleaner paper element See Note A
Clean and regap or replace spark plugs See Note A
Note:
A. Refer to Supplied Engine Manufactures Owner’s Manual for all
maintance and engine manufactures warranty policy information
Lubrication
The following recommendations on lubrication chart
below should be adhered to. Environmental conditions
may be cause to vary frequency. Grease points are
pointed out in Figure 2.
Battery
The battery is located under the seat of the machine.
The gel-cell battery is maintenance free.
 CAUTION:
When servicing the battery or any other part of the
electrical system, or if the battery must be removed
for any reason, always, disconnect negative (ground)
cable FIRST and reconnect it LASTto avoid possibility
of electrical shorts.
At temperatures below 32° F (0° C), full charge state
must be maintained to prevent cell electrolyte from
freezing and causing permanent battery damage.
For longest service life, battery should be kept clean by
wiping it off with a paper towel. Any corrosion around
battery should be removed by applying a solution of
one part baking soda to four parts water. A light coating
of grease or petroleum jelly may be applied to all
exposed terminal surfaces to prevent corrosion.
Tire Pressure
This vehicle has been designed to achieve maximum
operator comfort and ride. This cannot be achieved
without proper tire pressure. A low pressure gauge is
required to check the front tires.
Front Tires - 15-20 PSI
Rear Tires - 15-20 PSI
Lug nuts should be checked regularly for tightness.
Torque lug nuts to 50ft./lbs. The center hub nut should
be torqued to 175-200ft./lbs.

ENCORE
D-3
 CAUTION:
DO NOT SPILL OIL OR GREASE ON BELTS.
Oil And Filter
Hydraulics
The hydraulic system on this Encore Rider are lled
with 20W50 motor oil which will require approximately 7
quarts of oil to ll.
The hydraulic oil should be changed after every 500
hours or annually, which ever comes rst. The oil
should also be changed if the color of the uid has
become black or milky. A black color and/or a rancid
odor usually indicates possible over heating of the
oil, and a milky color usually indicates water in the
hydraulic oil.
 CAUTION:
Never add fuel to the tank while the engine
is running or hot. ALWAYS WAIT at least
five minutes before refueling and REFUEL
WITH THE ENGINE OFF. KEEP FUEL AWAY
FROM SPARKS OR FLAMES. WIPE AWAY
any fuel spillage BEFORE starting unit. Never
ll the fuel tank indoors. Wipe up any spilled
gasoline. Gasoline is highly ammable - NO
SMOKING.
NOTES:
Consult engine manual for engine manufactures
recommendation on operation, maintenance
information and engine warranty information. Engine
information will not be repeated in this manual.
 WARNING:
1. Gasoline is harmful or fatal if swallowed.
2. Long-term exposure to vapors can cause serious injury
and illness.
3. Avoid prolonged breathing of vapors.
4. Keep face away from nozzle and gas tank or container
opening.
5.Keep gas away from eyes and skin.
 WARNING:
To avoid serious Burn injuries:
Allow engine, and hydraulic uids to cool before
servicing transmission or engine systems.
Park mower on a level surface and stop the engine.
Place a suitable container under the hydraulic oil
reservoir. Remove the ll cap from the reservoir.
Remove the drain plug from the bottom of the tank and
allow oil to drain into the container. While the reservoir
is draining replace the hydraulic lter. Replace the drain
plug and ll reservoir to sight glass (located in the rear
side of the tank).
Engine
Please refer to the engine manual for engine
maintenance recommendations. (See Notes Above)
72" MID CUT
GEAR BOX
52-61" MID CUT
GEAR BOX
 CAUTION:
To avoid serious Burn injuries:
The cutter deck gearbox can reach high operating
temperatures. Allow the cutter deck gearbox to cool
before servicing
Gear Box
The uid level in the gear box should be checked after
every 100 hours of operation or bi-weekly, which ever
occurs rst.
Remove ignition key and raise deck to transport
position. Clean and remove the check plug from the
side of the gearbox. Visually check that the lubricant
level is up to the bottom edge of the check-plug hole.
If lubricant is low, add SAE 80W90 lubricant through
the check-plug hole. Install the check plug and tighten
securely. The lubricant in the cutter deck gearbox
should be changed after every 500 hours of operation
or yearly, whichever occurs rst.
Place a suitable container beneath the cutter deck
gearbox and locate the gearbox drain plug. Remove
the drain plug, drain the lubricant into the container and
properly discard it.
Reinstall the drain plug and add SAE 80w90 lubricant
through the check-plug in the gearbox, until it is level
with the bottom of the check-plug hole. Install the check
plug and tighten securely.

ENCORE
D-4
Drive Adjustment
If the mower is not tracking straight or if the unit creeps
in the “Neutral Stop” position proceed with the following
instructions.
TIRE PRESSURE:
Checking air pressure in the tires is critical for proper
drive or tracking.
NOTE: DO NOTADD ANY TYPE OF TIRE LINER OR
FOAM FILL MATERIAL TO THE TIRES!
Excessive loads created by foam lled tires may cause
failures to the hydro drive system, frame and other
components. Foam lling tires will void warranty.
Front tires: 15 to 20 psi
Drive tires: 15 to 20 psi
Tracking Adjustment
If the machine pulls left or right on a level, at surface
begin by checking the tire pressure. The front tires
should have 15 to 20 PSI and the rear tires should have
15 to 20 PSI. If tire pressures are correct examine the
dampening cylinders. The cylinders are preset from
factory to limit the forward motion of the control levers.
(When the control lever is at full speed, all the way
forward in the control slot, the damping cylinder should
bottom out.) To adjust tracking, loosen the two bolts
on the cylinder adjusting plate. Push adjusting plate
to move the cylinder forward on the fast side. This will
restrict the movement of the control lever to even out
tracking. Always slow the fast side of the machine down
if tracking is necessary.
Note: On uneven surfaces the operator is
responsible in keeping the machine traveling in a
straight line.
Neutral Adjustment
1. Raise the drive wheels of the mower off of the
ground. Safely block the frame in this position so it is
secure.
2. With the unit blocked up securely and the arms in
the neutral position (in the lock out position) sit in the
operators seat and start the engine. With the engine
running release the park brake and check to see if
there is any wheel creep (any rotation).
3. If wheels rotate with the control levers in lock
position, stop the engine and remove the belt cover
between the seat frame and engine by removing the
2 - 1/4 x 3/4 bolts.
4. All neutral creep (rotation) should be adjusted out
of the drive. This adjustment is performed at the
adjustable Pump Link on each corresponding pump.
( See g. ) Loosen the jam nut between the ball stud
and the control rod. Thread the stud into the control
rod if there is forward rotation and out of the control
rod if there is reverse rotation. Never adjust the link
more than 2 full turns at a time. Retighten the jam
nut and start the engine, and repeat step #2.
5. If the wheel still rotates in the Neutral Lock position
with the brake OFF repeat step #4.
RETURN
LINK
SPEED
CYLINDER
CYLINDER ADJUSTING PLATE
( SLOWER )
( FASTER )
PUMP LINK
REVERSE LIMIT
STOP
JAM NUT

ENCORE
D-5
Belt Adjustment
Remove key from the ignition switch. Remove the
key from ignition switch. Flip up the foot plate (See g.
3) to gain access to the deck drive belt and the eyebolt
assembly that is used for adjusting the spring tension.
The spring tension is measured by the gap between the
coils and should be approximately 1/8”. By turning the
5/16” nylock nut on the end of the eyebolt clockwise, it
will increase tension. Moving the deck bracket into the
second slot (See g. 3) may also increase tension.
Brake Adjustment
After the rst 40 hours of use check brakes for
adjustment. Brakes are adjusted by setting the
lock collars on the brake rods located by each
drive wheel. There must be 1/8 to 1/4 inch of gap
between the lock collar and swivel with the brake
in the ON position. This distance should be
checked bi-weekly. After adjusting the lock collar,
you may have to also adjust the brake link by
pulling the hair pin clip and adjusting swivel
accordingly.
Deck Leveling
Adjustment
The deck comes from the manufacturer preleveled. If
the deck does not appear to be cutting level, follow this
procedure.
1. Set all tire pressures to correct specication.
2. Place machine on a level cutting surface and inspect
blades to make sure that one is not damaged or
bent.
3. Stop engine and Remove the ignition key. While
wearing heavy gloves rotate the blades so that they
are all pointing to the forward side of the deck. (See
g.1) Measure from the blade tip to the ground on all
three blades. If there is more than 3/16” difference
from one side of the deck to the other, the deck
should be leveled.
BELT TENSION ADJUSTMENT
FIG. 3
BLADE TIPS
DISCHARGE
SIDE
( BOTTOM VIEW )
FIG. 1
CLEVIS PIN
LIFT SPRING
ROD
LIFT SPRING
SPRING TENSION
BOLT
FIG. 2
4. To adjust the deck height, remove the clevis pin
from the lift spring rod. This may be accomplished
by moving the lift arm to a point that relieves the
pressure off the pin. (See g.2) To raise the deck,
thread the back of the spring rod clockwise. To lower
the deck, turn the spring rod counter clockwise
(Note: When changing the length of the spring rod do
so in two turn increments). At this time also inspect
the bushings or washers, at the base of the spring
(by the spring bolt) and check for binding.
5. Reassemble the spring rod and replace the clevis
pin. Now move the deck up and down and recheck
the side to side blade measurement.
LOCATED BY THE WHEEL
MOTOR AREA
LOCATED BY THE SEATAREA
UNDER METAL FENDER
SWIVEL
HAIR PIN
CLIP
BRAKE
ASSEMBLY
CLAMP COLLAR
SWIVEL
BRAKE
LINK
ADJUST CLAMP COLLAR TO
APPROX. 3/16" GAP FROM
SWIVEL WITH BRAKE ON

ENCORE
D-6
Deck Cutting Height
Adjustment
Foot Deck Lift Option
To adjust the cutting height, place foot on the foot
pedal, press down until it is locked in the up position,
and then remover the height adjustment pin to the
desired cutting height. Once the has been done,
press down on the foot pedal and with your right hand
reach down and push the plastic section of the height
adjustment towards the front of the mower. This will
allow you to slowly release pressure with your foot
which in turn will allow the deck to lower down to your
desired cutting height.
Electric Deck Lift Option
To adjust deck cutting height, simple press the up or
down switch on your left side on the side panel next
to the seat to raise or lower the deck cutting height
a deck cutting height gage located by the right front
caster.
Important Note:
Cup side of spring washer
goes against blade.
Spring
Washer
Blade
Blade
Bolt
Figure 9
 CAUTION:
TURN OFF ENGINE AND REMOVE KEY BEFORE
MAKING ANY ADJUSTMENTS.
Mower Blades
Check sharpness of mower blades after every 10 hours
of operation. To sharpen blades proceed as follows:
Block front end of mower up or run front up on
ramps.
Remove blade by turning bolt counter clockwise.
Blades should be discarded when worn excessively.
See Sketch.



Sharpen blade with a hand le, electric grinder or
blade sharpener. Wear gloves and eye protection
when sharpening. Grind blade at original bevel.
Check balance of blade by positioning the blade on
a nail or blade balance pedestal. Grind the blade
on the end that is heavier until both sides balance.
Do not wear loose
tting clothing
which could get
caught in moving
parts. Always
be sure to wear
adequate protective
clothing. Wearing
safety glasses and safety shoes is advisable.
Reinstall blades. Refer to Figure 9 for further
information




.EW"LADE
25 Degrees When Notch Starts
Discard Blade Dangerous!
 DANGER 
Observe usual fuel handling precautions:
Do not smoke while refueling.
Do not fill tank with engine running or while engine is hot.
Clean up any gasoline spills.
Allow engine to cool before storing machine inside a building.
Keep fuel away from open flame or spark and store mower away
from open flame or spark if this fuel in the tank.
Use extra caution when handling gasoline and other fuels: They
are flammable and vapors are explosive. A fire or explosion from
gasoline or other fuels can burn you and others and can damage
property.
Refuel outdoors preferably, or in well ventilated areas.
Never attempt to start engine when there is a strong odor of fuel
fumes present. Locate and correct cause.
Store gasoline in an approved container and keep it out of the
reach of children.
Never buy more than a 30 day supply of fuel.
Always place fuel containers on the ground away from your vehicle
before fueling.
Do not fill gasoline containers inside a vehicle or a truck or a trailer
as interior carpets or plastic truck bed liners may insulate the
container and slow the loss of any static charge.
When practical, remove equipment from truck or trailer and refuel
mower with its wheels on the ground.

ENCORE
E-1
PURPLE 18 GA
LEVER
NEUTRAL
SWITCH
N/O
PARK BRAKE
SWITCH
RED w/BLACK 18 GA
RED w/BLACK 18 GA
PTO SWITCH
BROWN 18 GA
BLUE 14 GA
BLUE 14 GA
COM
N/C
REAR VIEW OF
TIMEDELAY CONN.
BLACK 18 GA
N/O
A D FECB
WHT/PUR 18 GA
PURPLE 18 GA
PINK 18 GA
RED 12 GA
ENGINE
CONNECTOR
GREEN 18 GA
GRAY 12 GA
RED 12 GA
RED 12 GA
KEY SWITCH
WIRE JUNCTION
IGNITION SWITCH
WHITE w/YELLOW 18 GA
FUEL FILTER
SWITCH
WHITE w/BLUE 18 GA
WHITE w/BLUE 18 GA
ALARM
BLACK 18 GA
POS
PINK 18 GA
TEMP
OIL
FUSE BLOCK
PURPLE 18 GA
REDw/WHITE 18 GA
GREEN 18 GA
BROWN 18 GA
NEG
RED w/BLACK 18 GA
WARRNING
LIGHTS
ALT
FUEL FILTER
GLOW PLUG LIGHT
GRAY 18 GA
WHITE w/BLUE 18 GA
WHITE w/BLUE 18 GA
PUR 18 GA
RELAY SPST (2)
BLUE 14 GA
YELLOW 18 GA
WHITE w/YELLOW 18 GA
30 AMP
15 AMP
GRAY 12 GA
HOUR METER
BLACK 18 GA
PUR 18 GA
REDw/WHITE 18 GA
END OF HARNESS
GRAY 18 GA
BLK / ORG 18 GA
TIMER
BATTERY POST
N/O
BLACK
18 GA
BLACK 18 GA RED 12 GA
GLOW PLUG
RELAY
GREEN w/ORG 18GA
GRAY 12 GA
REDw/WHT 18 GA
ELECTRIC CLUTCH
BLUE 14 GA
BLACK 14 GA
WHITE w/BLUE 18 GA
30 AMP
GRAY 12 GA
RED 12 GA
YELLOW 18 GA
GREEN w/ORG 18GA
SEAT SWITCH
RED w/BLACK 18 GA
ALL VIEWS OF CONNECTORS
ARE FROM WIRE-IN SIDE
BLUE 14 GA
WHITE w/BLUE 18 GA
RED w/BLACK 18 GA
ENCORE PART #: 593051
WIRE HARNESS FOR 61B27LD ; 27 HP BRIGGS - DIESEL
WIRE HARNESS FOR 72B27LD ; 27 HP BRIGGS - DIESEL

ENCORE
E-2
GREEN 18 GA
RED 12 GA
GRAY 12 GA
WHITE w/BLUE 18 GA
ENGINE OIL PRESSURE
ENGINE CONNECTOR
(ENGINE SIDE)
BROWN 18 GA
ALL VIEWS OF CONNECTORS ARE FROM WIRE-IN SIDE
GLOW PLUGS
STARTER SOLENOID
YELLOW 18 GA
WHITE w/YELLOW 18 GA
RED w/BLACK 18 GA
FUEL SHUTOFF
ENGINE
COOLANT TEMP
ALTERNATOR
OUTPUT
REGULATOR
CONNECTOR
ENCORE PART #: 583276
ENGINE WIRE HARNESS FOR 61B850P ; 26 HP BRIGGS - DIESEL
ENGINE WIRE HARNESS FOR 72B850P ; 26 HP BRIGGS - DIESEL
ENGINE WIRE HARNESS FOR 72B850ZP ; 26 HP BRIGGS - DIESEL
ENGINE WIRE HARNESS FOR B850PFC ; 26 HP BRIGGS - DIESEL
ENGINE WIRE HARNESS FOR 61B27LD ; 27 HP BRIGGS - DIESEL
ENGINE WIRE HARNESS FOR 72B27LD ; 27 HP BRIGGS - DIESEL

Notes
F-1

Notes
F-2

Notes
F-3

,ENCORE MANUFACTURING CO., INC.
All rights reserved. Contents subject to change. PART NUMBER
0812 A
PROWLER MID-CUT
72B27LDML - OPERATORS MANUAL
933240