REMET CNC RT-690R Guide

TECHNICAL DOCUMENTATION
USER MANUAL
WARRANTY CARD
SPARE PARTS CATALOG
PROFESSIONAL chipper
For PTO drive
RT-690R, RT-720R
with hydraulic feed rollers:
ReRead all instructions carefully before using the
device and familiarize yourself with all control ele-
ments. If in doubt, contact the manufacturer.
Keep the instructions in a safe place that allows
you to obtain the necessary information at any
time.
REMET CNC TECHNOLOGY
Spółka z ograniczoną odpowiedzialnością
36-053 Kamień, Łowisko 320A
NIP 5170374653
Instrukcja oryginalna

REMET CNC TECHNOLOGY SP. Z O.O.
Page 2 of 28
Producer of machinery and equipment, machining
Table of Contents
1. GENERAL SCHEME ........................................................................................................................... 3
2. PURPOSE AND GENERAL DESCRIPTION OF THE APLIANCE ............................................................. 4
3. SPECIFICATION OF THE DEVICE ....................................................................................................... 5
4. SAFETY INSTRUCTIONS .................................................................................................................... 6
Personal protective equipment and pictograms............................................................................. 7
Aggregated with a tractor ............................................................................................................... 9
5. CONTROL OF WORK AND SAFETY ZONE........................................................................................ 10
WORK- MATERIAL INTAKE............................................................................................................. 10
STOP - EMERGENCY STOP ............................................................................................................. 10
REMOVING MATERIAL................................................................................................................... 11
RETURN TO INTAKE THE MATERIAL .............................................................................................. 11
SAFETY ZONES DURING INTAKE OF MATERIAL ............................................................................. 12
SAFETY ZONES WHILE WITHDRAWING MATERIAL........................................................................ 13
Hydraulic system and feed control................................................................................................ 14
The rules of safe work performance ............................................................................................ 14
Activities after finishing work........................................................................................................ 15
Rules of conduct in emergency situations posing threats to the life or health of employees...... 16
6. PROHIBITED ACTIONS.................................................................................................................... 17
Notes and first aid ......................................................................................................................... 18
7. TRANSPORT AND STORAGE OF THE APPLIANCE ........................................................................... 18
8. ADAPTATION OF THE POWER TRANSMISSION SHAFT .................................................................. 19
9. REPLACEMENT AND ADJUSTMENT OF AXLES ............................................................................ 20
10. REPLACEMENT PARTS AND ASSEMBLY ......................................................................................... 21
Spare parts and assembly.............................................................................................................. 21
11. MAINTENANCE AND CLEANING ................................................................................................... 25
Safety instructions for maintenance. ............................................................................................ 25
General activities related to maintenance and cleaning............................................................... 25
12. DISPOSAL AND ENVIRONMENT PROTECTION............................................................................... 25
13. SOLUTIONS FOR EXEMPLARY PROBLEMS ..................................................................................... 26
14. GUARANTEE CARD......................................................................................................................... 27
PRINCIPLES OF THE WARRANTY GUARANTEE:.......................................................... 27
15. DECLARATION OF CONFORMITY CE ............................................................................................. 28

REMET CNC TECHNOLOGY SP. Z O.O.
Page 3 of 28
Producer of machinery and equipment, machining
1. GENERAL SCHEME

REMET CNC TECHNOLOGY SP. Z O.O.
Page 4 of 28
Producer of machinery and equipment, machining
2. PURPOSE AND GENERAL DESCRIPTION OF THE
APLIANCE
The device is designed for crushing woody and fibrous garden waste such as
tree trunks and branches.
ATTENTION:It is forbidden to put stones, glass, metal, bone, plastic, textiles and
other materials in the chipper mechanism feeder. Any use other than those speci-
fied in these operating instructions may damage the device and create a serious
hazard to the operator. The operator or user bear the entire responsibility for the
injuries and damage caused to third parties and their property. The manufacturer
does not bear any responsibility for damages and unfortunate events caused by
improper use and device operation, including any changes and modifications in-
troduced by users and operators who also carry out this immediate loss of war-
ranty.
The chipper is equipped with a disc cutting system (hardened knives made of
hard-wearing steel). The cut material is pulled in using hydraulic feed rollers with
the possibility of engaging reverse gear. The device is equipped with a safety
switch surrounding the feeding hopper, which after switching on interrupts the
operation of the feeding rollers. The chipper has metal (opening) covers for the
inlet feeder and cutting disc for safe operation. A solid structure equipped with a
3-point hitch system ensures durability and stability of the device.
ATTENTION
This symbol is used in this manual if there is a danger to
the user or unauthorized persons.
This
symbol is also used when there is a threat to the
environment or property.
INCORRECT OPERATION OF THE MACHINE CAN
CAUSE BODY DAMAGE OR DEATH. BEFORE
USING THE MACHINE, IT IS NECESSARILY RE-
ADING THE INSTRUCTION MANUAL.

REMET CNC TECHNOLOGY SP. Z O.O.
Page 5 of 28
Producer of machinery and equipment, machining
3. SPECIFICATION OF THE DEVICE
Technical parameters:
Typ RT-690R RT-720R
MINIMUM/RECOMMENDED POWER
[HP] 35/60* 55/80*
RECOMMENDED SHAFT SPEED
PTO[rpm](clock ways) 540-1000 540-1000
DIAMETER OF CUTTING DISC [mm] 625 720
WEIGHT OF CUTTING DISC [kg] 60 85
NUMBER OF KNIVES 4 + 1 cuntter knive 4 + 1 cuntter knive
EXECUTION OF CUTTIN KNIVES Stal HARDOX type 500 Stal HARDOX type 500
RECOMMENDED OVERLOAD CLUTCH
[Nm] 900-1700 900-1700
FASTENING SYSTEM OF WOOD
CHIPPER
THREE-POINT SUSPENSION
SYSTEM
three-point suspension sys-
tem
MAX.CUTTING DIAMETER OF FRESH
SOFTWOOD [mm] * 130 170
MAX.CUTTING DIAMETER OF FRESH
HARDWOOD [mm] * 110 150
MAX.CUTTING DIAMETER OF DRY
HARDWOOD [mm] * 90 120
Addictive rollers
Hydraulic drive
Hydraulic drive
Required oil flow
60 l/min
60 l/min
ROTATION ANGLE OF OUTLET 360˚ 360˚
HEIGHT OF OUTLET PIPE [cm] 170 210
WEIGHT [kg] 330 450
*The maximum diameter of shredded branches depends on the type of wood and
the conditions when cutting the material. For hardwood (eg oak / beech), the ma-
ximum cutting diameter will be smaller than soft wood (eg pine, spruce). In the
case of dry or gnarled wood, the maximum cutting diameter will also be reduced.
**The clutch selection parameter should be corrected with max. the PTO's torque
in the tractor.

REMET CNC TECHNOLOGY SP. Z O.O.
Page 6 of 28
Producer of machinery and equipment, machining
4. SAFETY INSTRUCTIONS
GENERAL THOUGHTS
1. The chipper must not be used by:
•Persons who are entitled,are not trained ora re under the influence of alcohol
or narcotic drugs and psychotropic substances(drugs) and drugs which impair
the reaction capability
•Children (below the minimum age of the operator determined by local regula-
tions), ,
•Pregnent women,
•People with limited mental abilities.
2. Before the first start-up of the device, the operator should familiarize himself
with the user's manual issued by the device manufacturer and make sure it knows
the operation of all control devices.
3. In addition, employees operating the chipper must have appropriate quali-
fications and have appropriate health and safety training in order to learn safe
rules and proper service..
4. To perform the work with the chipper, two trained persons are required, the
chipper operator and the operator of the driving tractor.
5. Operators must provide sufficient space and hardened and no slippery sur-
face to work with the device.
6. Operators performing work with chipper should constantly observe the work
area and should never allow any third persons or animals to stay in the working
area of the machine.
7. The chipper operators are responsible for the safety of unauthorized persons
or animals that may be near the machine.
8. Works with the use of a wood chipper may only be performed by adults who
are trained by the employer.
9. An employee performing work with a chipper must be rested, healthy and
in good physical condition.
10. Do not work during rain or bad weather, operate only in daylight or good
artificial light..
11. Do not overload the device, it may damage bearings, cutting disc, hydraulic
lines and connectors, which may result in immediate threat to health and life.
12. Work prudently and take regular breaks
13. It should be ensured that the chipper knives are always sharp.
Incorrect use of the device can cause serious injury.

REMET CNC TECHNOLOGY SP. Z O.O.
Page 7 of 28
Producer of machinery and equipment, machining
Personal protective equipment and pictograms
When working with the wood chipper, use it:
•glasses / face mask
•hearing protectors
•protective gloves
•protective footwear
•protective clothing, close fitting to the body, without loose, sticking straps or sleeves.
Mark
Description
Mark
Description
Use hand protection
No unauthorized person!
Use foot protection
Do not put your hands into the feeder's
oil, Keep a safe distance from the inlet
opening and the ejec-tion area.
Use safety glasses
Warning! Danger of injury from rotating
gears. Keep your hands and feet away
from the openings during machine ope-
ration.
Use hearing protection
Attention, it is possible to cut your fin-
gers/hands!
Read the user's manual
Attention the possibility of pulling, inter-
ception!
Do not put your hands into the feed
hopper!
Obligation to lubricate the gear
transmission
Attention danger!!
Recommended propeller shaft
speed: 540-1000 rpm
Attention rotating blades, danger of cut-
ting your fingers!
No walking on the surface of the
inlet funnel!
Do not go in, stand up!
Warning! High oil pressure!
Use personal protective equipment.
Attention, fine parts falling out at high speed, use personal protective
equipment (full-face mask)

REMET CNC TECHNOLOGY SP. Z O.O.
Page 8 of 28
Producer of machinery and equipment, machining
Warning! Rotating parts, danger of being caught.
Safety signs:
1. Keep safety signs in a clean and legible condition.
2. Immediately replace any safety signs that are missing or illegible.
3. For the replaced parts that have a safety mark / sign, also use the current
mark.
4. Safety signs are available from an authorized distributor or in the
commercial / serial department of the factory.
Installation of safety signs :
1. The place of installation must be degreased and wiped dry.
2. Apply warning signs when the temperature is more than 10˚C (50˚F).
3. Before removing the protective paper, a suitable application location must
be established.
4. When removing the protective paper of the adhesive layer, apply a warning
sign and then smooth it with a protective paper.
Things to do before you start working
Before commencing work, it is necessary:
1. Review the chipper before each use. Check that the safety and propulsion
system works correctly. If not, the system should be repaired before starting the
chipper.
2. Before starting work it is necessary to make sure that all covers are properly
secured (check the tightening of the screws).
3. The machine should be placed on an even, hard, non-slip surface with
extreme caution.
4. Before commencing grinding, make sure that there are no bystanders or
animals near the machine.
5. Before switching on the engine in the tractor, check the chipper attachment.
6. Wear a helmet or other covering covering the hair, safety goggles, hearing
protection and protective clothing. The person operating the machine should not
wear a scarf, tie, too loose clothing (clothing recommended to be adhering to the
body) and gloves intended for other work (eg skin welding).
7. Damaged or illegible stickers must be replaced.

REMET CNC TECHNOLOGY SP. Z O.O.
Page 9 of 28
Producer of machinery and equipment, machining
Aggregated with a tractor
1. Observe the recommended minimum front load of the tractor in order to
maintain stability.
2. Należy Be especially careful when coupling the shredder with the tractor and
during its disconnection.
3. Every time before starting work, all the safety switches and the hydraulic
system must be checked for correct operation.
4. It is strictly forbidden to stay between the chipper and the tractor and in the
short distance while operating the lever to operate the hydraulic system.
5. It is forbidden to stay anyone between the tractor and the chipper during
work.
6. Only use PTO shaft with cover and clutch. Work with a shaft without a cover
or with a damaged cover is categorically defended.
7. The shaft guard must be secured against rotation, eg with a chain-link.
8. Work without WPM guards (power take-off shaft in the machine) and PTO
shaft (power take off shaft on the tractor) is prohibited.
9. The power transmission shaft must be of sufficient length.

REMET CNC TECHNOLOGY SP. Z O.O.
Page 10 of 28
Producer of machinery and equipment, machining
5. CONTROL OF WORK AND SAFETY ZONE
WORK- MATERIAL INTAKE
STOP - EMERGENCY STOP