Rescea RVH-AXP35-VF User manual

SONY FDR-AX30/AX33/AXP33/AXP35 4K Camcorders
Waterproof ousings
Recsea RVH-AXP35-LCD
RVH-AXP35-VF
MANUAL
Please read this manual before use.
NTF CORPORATION U Division
http://www.seatool.net

INTRODUCTION
SONY FDR-AX30/AX33/AXP33/AXP35 Waterproof ousing RV -AXP35
※ Thank you for purchasing the RV -AXP35 Waterproof ousing.
※ To ensure proper and safe use, please thoroughly read this manual.
※.Improper use may cause leakage causing irreparable damage to your digital video
camera.
※ Please check, and test the housing according to this manual prior to use.
※Neither NTF Corporation, Resea nor their agents shall warrant or bear any responsibility
for any incident related to water leakage, damage or loss of data, unauthorized
modification, disassembly and repair; or any accident causing physical or material
damage while using this product.
※This product is manufactured by machining methods. As a result, there may be minor
scratching or tool marks. These are a normal part of the manufacturing process, do not
effect operation of the housing or camera, and are not subject to warranty or any other
claims.
WARNING!
※ Do not store or leave housing in reach of infants or small children. The strap may cause
chocking and suffocation, or small parts may be swallowed causing injury.
※ Please remove digital video camera from housing when not in use. Battery malfunction or
damage may cause fire.
※This housing is partially constructed of plastic resin (POM). Please be careful of strong
impact which may cause damage and/or injury due to sharp edges.
CAUTION!
※Before using, please be sure the test the housing (without camera) in freshwater.
※ To prevent water leakage and damage, DO NOT disassemble or modify this housing.
※ Do not store the housing in areas of high humidity, high or low temperatures, or areas of
extreme temperature fluctuation. Doing so may cause deterioration of parts.
※ When diving, use a method of water entry that protects the housing from shock, which can
cause water leakage. If at all possible have housing handed to you after entering the
water.
※ This housing is designed to withstand depths of 100 meters (328 feet). Using the housing
at deeper depths may cause damage and water leakage. Use caution and monitor depth.
※Remove O-rings or leave housing slightly open when transporting by plane. Pressurization
of a sealed housing during transport may cause damage or make it difficult to open.
※ When opening and closing the housing be mindful of dust and other contaminants, which
may adhere to the O-rings, possibly causing water leakage and damage.
※ Always check O-rings prior to each use. Pay special attention to the grease condition and
that O-rings are seated uniformly in the O-ring grooves with no twists or bulges. Neglecting
to check the O-rings prior to each use may result in water leakage and damage.
※Please keep inside of housing dry. umidity, environment and temperature difference may
cause condensation. To prevent condensation please use commercially available silica
gel packets.
※For replacement of consumable parts such as O-rings please contact your dealer or
Seatool/Recsea.
※A complete ousing overhaul is recommended once every year.
FEATURES OF T IS PRODUCT
※Compact and durable, CNC precision machined corrosion-resistant aluminum and POM
housing.
※Lightweight, ergonomically designed.
※Maximum Operating Depth (MOD) 100 meters (328 feet).
1

※RECSEA Airlock Vacuum System w/Gauge and Pump.
※Electronic remote control via SONY RM-VPR1 Remote Controller.
※Manual Ring Dial and Manual Button.
※Removable LCD Port (RVH-AXP35-LCD) and LCD Port Cover (RVH-AXP35-VF).
※M67 Lens Port.
※RECSEA original Secure-Latch locking system for easy opening and closing.
※EO 26-5FBRA-4 and Aquatica Bulkhead Ports for external monitors.
※Two (2) M10 Ball Joint Sockets.
※Quality silicone Back Cover O-ring with wide Back Cover contact surface.
※Variety of supported RECSEA original options.
PACKAGE CONTENTS
Be sure all items listed here were included with your housing:
・LCD Port (RVH-AXP35-LCD) ・LCD Port Cover (RVH-AXP35-VF)
・LCD Grip & Tray Assembly (RVH-AXP35-LCD) ・Viewfinder Grip & Tray Assembly (RVH-AXP35-VF)
・SONY RM-VPR1 Remote Commander ・RECSEA Airlock Vacuum System
・Camera Tray ・Wrist Strap
・Reserve O-rings ・SEATOOL O-ring Grease w/O-ring Pick
GETTING TO KNOW YOUR RV -AXP35 OUSING
RV -AXP35-LCD
RV -AXP35-VF
2

RV -AXP35-LCD / RV -AXP35-LCD
RV -AXP35-LCD
RV -AXP35-VF
3

RV -AXP35-LCD RV -AXP35-VF
※.Viewfinder - For use with camera's viewfinder. Can easily be replaced with optional INON
45° Viewfinder Unit witout the need of an adapter.
4

※The RV -AXP35-LCD and RV -AX35-VF come with a SONY RM-VPR1 Remote Controller
unit installed. Do NOT attempt to remove it. Should you experience problems with the unit,
contact SEATOOL/RECSEA or the dealer of from which purchase was made.
NOTE: Camera’s NIG TS OT Light cannot be used with this housing.
REMOTE COMMAND FUNCTIONS
・Power Button Turns camera only ON and OFF.
・REC Button Press the REC Button to START recording.
Press the REC Button again to STOP recording.
・Photo Button alf-press the Photo Button to bring the image into focus, and then press
the button all the way.
CAUTION: Do not press Photo Button with excessive force, or the remote
may break.
・Zoom Lever Activates remote Zoom Buttons T/W
Up - T side (telephoto): Subject appears closer.
Down - W side (wide angle): Subject appears farther away.
NOTE: Zooming speed is slow when you press the zoom button lightly,
and quick when you press the button all the way down.)
5

OUSING MANUAL CONTROL FUNCTIONS
・Manual Button ・Manual Dial Zoom
Focus
Exposure
IRIS
Shutter Speed
AE Shift
White Balance Shift
RESET
NOTE: Desired camera manual functions must be assigned to prior to use with housing.
※The housing Manual Dial is designed to turn the camera dial back and forth via friction
from the O-ring that come in contact with camera inside the housing. When installing or
removing camera pull Manual Dial out away from housing. After installing be sure to place
the Manual Dial into the proper position. Should the O-ring of the internal control wheel
of the housing begin to slip, use a soft dry cloth to wipe away any oil and other
contaminates that may cause the loss of friction from both the camera function and O-ring.
ANDLING PRECAUTIONS
※When opening back cover after use in water, due to negative pressure there is the
possibility of water on the housing being sucked into the interior. Prior to opening back
cover it is strongly recommended to wipe all water off the housing using a soft, dry cloth.
In the unlikely event water sucked inside, please remove with a clean, dry cloth
※When opening housing or conducting maintenance please do so in a clean place with low
humidity and dust.
※ To help prevent condensation within the housing, it is recommended to conduct installation
of camera and O-ring maintenance in an air conditioned room. Silica gel pack(s) may also
be use placing them in a way as not to interfere with camera our housing functions.
※ Please be careful not to damage when moving during packing and transport.
※Remove O-ring or leave housing slightly open by placing a strip of paper between the
housing main body and back cover when transporting by plane. Pressurization of a sealed
housing during transport may cause damage or make it difficult to open.
INSTALLING CAMERA IN OUSING
※Please conduct the following operations in a clean place with low humidity and dust.
1. Remove camera lens cap, check camera settings, battery is charged and media
storage capacity is sufficient.
2. Using the camera's tripod mount screw socket, firmly attach Camera Tray to camera
as shown below making sure there are no gaps between the camera and the
Camera Tray.
6

3. To OPEN RV -AXP35 back cover, while pressing the Lock Levers (1) on both sides
of the housing pull the Secure-Latches (2) away from the back cover.
4. a. RV -AXP35-LCD
With housing LCD Port removed and camera LCD open, set camera (Camera
Tray attached) into position as shown below taking care to line up the Camera
Tray Posts with the grooves on the Camera Tray. Once aligned slowly push
forward into the housing until it stops.
7

b. RV -AXP35-VF
With camera LCD closed, set camera (Camera Tray attached) into position as
shown below lining up the Camera Tray Posts with the grooves on the Camera
Tray. Once aligned slowly push forward into the housing until it stops.
Fully extend camera's viewfinder as shown above.
※When installing camera take care that camera's Grip Belt does not cause an obstruction.
※With RV -AXP35-VF be sure to extend camera's viewfinder. If this is not done the camera
will not be turned ON when using the Remote Commander. Camera will remain ON until
the Power Button is used to turn camera OFF, or until Power Save setting engages.
5. Using the SONY RM-VPR1 Remote Commander Cable provided, connect camera
to the remote via the Multi/Micro USB Terminal and RM-VPR1 Remote Cable
Terminal as shown below.
8

※Gently tuck access cable into housing so that it does not cause an obstruction when
attaching the back cover.
※Please perform proper O-ring and O-ring Contact Surface maintenance prior to attaching
and closing the back cover. Pay special attention to the grease condition making sure the
O-ring is free of contaminants and seated uniformly in the O-ring groove with no twists or
bulges.
6. Carefully place back cover onto housing main body. Press Secure-Latch (2) on both
sides making sure the latch on the underside is properly placed in the Secure-Latch
Groove (1) on both sides of the back cover. Push into the locked position. Double
check to make sure both Secure-Latchs are firmly locked into place.
INSTALLING LCD PORT (RV -AXP35-LCD)
※Please conduct the following operations in a clean area with low humidity and dust.
※Please perform proper LCD Port O-ring and housing port contact surface maintenance
prior to installation.
1. Pull LCD Dial on the LCD Port outward so that it does not cause an obstruction.
2. Place LCD Port over ousing Port aligning the tabs of the LCD port with the ousing Port
as shown on the next page.
9

3. Rotate LCD Port clockwise until it stops with an audible “click” as the LCD Port Lock
Button engages.
4. After LCD is attached, set the LCD Dial.
INSTALLING LCD PORT COVER (RV -AXP35-VF)
※Please conduct the following operations in a clean area with low humidity and dust.
※Please perform proper LCD Port Cover O-ring and housing port contact surface
maintenance prior to installation.
1. Place LCD Port Cover over ousing Port aligning the tabs of the cover with the port as
shown on the next page.
10

2. Making sure the cover is resting evenly on port, push the cover into the port until it is fully
seated.
3. Rotate cover clockwise until it stops with an audible “click” as the LCD Port Lock Button
engages.
USING T E VIEWFINDER
The housing Viewfinder is interchangeable with INON 45°Viewfinder Unit, no modification or
adapter required.
※Once housing is properly closed perform Pre-Dive Check using Airlock Vacuum System
while testing camera and housing functions. Pre-Dive Check may also be conducted by
immersing housing several times, starting with short intervals, gradually lengthening time,
checking for water leakage after each intervals while testing camera and housing
functions.
※When entering water use a method of water entry that protects the housing from shock,
which can cause water leakage. If at all possible have ousing handed to you after
entering the water.
※After use in salt water, wash off salt and other contaminants by soaking empty ousing,
with Back Cover properly attached, thoroughly in a bucket of fresh water (lukewarm) for 10
to 20 minutes. Manipulate all buttons and dials several times to flush out salt deposits and
other contaminants.
※After use always conduct proper housing, O-ring and O-ring contact surface maintenance.
AIRLOCK VACUUM SYSTEM
The RV -AXP35 comes equipped with an Airlock Vacuum System to conduct Pre-Dive
checks without having to submerse the housing in water. In addition to checking seals this
system also acts as a second lock for LCD Port, LCD Port Cover and housing Back Cover.
※Always replace Vacuum Valve Plug prior to submersion in water.
11

For Vacuum:
1. Pull Valve Sleeve downward.
2. Plug will automatically rise from Valve.
3. Remove Plug from Valve.
4. Attach Gauge to Valve.
5. Pump ousing to -0.04 MPa. (Note: While pumping the Gauge will fluctuate.)
6. Wait for approximately 10 minutes.
a. If there is no pressure change, the housing is air and water tight.
b. If there is pressure change, there is the possibility of a leak.
Check housing and try again.
7. Pull Valve Sleeve downward to release Gauge.
8. Insert Plug into the Valve.
※Changes in temperature may cause pressure changes.
To Repressurize:
1. Remove Plug from Valve as instructed above.
2. Attach Gauge to Valve.
3. Press Repressurize Button at side off Gauge.
REMOVING CAMERA FROM OUSING
1. Turn camera OFF.
2. Remove Plug from Airlock Vacuum Valve.
12

3. Attach Gauge to Valve.
4. Press Repressurize Button and wait unit the Gauge reads 0 MPa.
5. Remove Gauge and attach Plug.
6. To remove LCD Port or LCD Port Cover, while pressing LCD Port Lock Button turn
LCD Port or LCD Port Cover counterclockwise until it stops. Carefully remove from
ousing Port.
7. Open back cover. Refer to INSTALLING CAMERA IN OUSING, 3.
8. Unplug SONY RM-VPR1 Remote Commander Cable from camera and remote.
9. Carefully remove camera from housing.
CAUTION! Neglecting to wash salt and other contaminants from the housing may result in
damage the housing raising the risk of leakage during future use. Damages due to the lack of
proper cleaning and maintenance is not covered under warranty.
ARMS & LIG TS INSTALLATION
The housing is equipped with two (2) M10/P1Ball Joint Base sockets and comes with a dual
grip and tray assembly which can be attached using two (2) tripod screw sockets located at
the bottom of the main body. Please use as needed.
CAUTION! Use the grip and tray assemblies provided. Leakage or damage due to the use of
other than assembly provided is NOT covered under warranty.
MAINTENANCE
CAUTION! Allowing saltwater and contaminants to dry on housing can damage functions and
O-rings possibly causing water leakage. Clean with fresh water only, using a soft, dry cloth to
wipe away water.
1. After extended periods of non-use, soak empty housing, making sure back cover is
properly attached, in lukewarm for half a day. Manipulate all buttons and dials several
times. Using a soft, dry cloth wipe away water.
After use in salt water, wash off salt and other contaminants by soaking empty housing,
back cover is properly attached, thoroughly in a bucket of fresh water (lukewarm) for 10 to
20 minutes. Manipulate all buttons and dials several times. Using a soft, dry cloth wipe
away water.
2. Remove Back Cover, LCD Port or LCD Port Cover and using the O-ring Removal Pick,
remove the O-rings.
3. Perform O-RING GREASING & MAINTENANCE as instructed below before re-installing.
O-RING GREASING & MAINTENANCE ( 1)※
CAUTION! DO NOT use silicone grease other than that provided by Seatool/Recsea.
1. Using the O-ring Removal Pick, remove Back Cover and LCD Port or LCD Port Cover O-
rings.
2. Clean sand, salt, other contaminants and old grease from O-rings.
3. Clean O-ring grooves and O-ring contact surfaces using a clean cotton swab.
4. Visually and physically check each O-ring by running it through finger tips, feeling for
cuts, cracks or any other defects that may cause leakage. Such defects will cause water
leakage, so be sure to replace defective O-rings. Be careful not to stretch or pull the O-
rings too much.
5. Squeeze a rice grain sized bead of silicone grease on your thumb and forefinger. Taking
care not to pull or stretch the O-ring too much, uniformly spread grease on each O-ring.
Too little grease may cause an O-ring to twist in the groove, possibly causing water
leakage.
13

6. Replace each O-ring making sure that it is uniform, not twisted or bulging out, possibly
causing water leakage. When closing Back Cover, LCD Port or LCD Port Cover, visually
check O-ring contact surfaces, tracing a finger over it making sure no hair, lint or other
contaminants are attached.
IMPORTANT NOTES:
※When ousing is not used for long periods, remove O-rings, place them separate plastic
bags to keep them free of dust and other contaminants and store in a place out of direct
sunlight. Please also be careful of prolonged exposure to direct sunlight during use. The
O-rings and housing may become deformed, causing water leakage.
※After extended periods of non-use, soak empty housing, with Back Cover and LCD Port or
LCD Port Cover attached in lukewarm for half a day. Manipulate all buttons and dials
several times. Using a soft, dry cloth wipe away water.
※We recommend a complete ousing overhaul once every year.
CAUTION!
※The O-rings are an essential part of waterproofing for this housing. Not properly greasing
the O-rings as directed may cause the O-ring to twist in the O-ring grooves, possibly
causing water leakage.
※Always perform proper O-ring, O-ring groove and O-ring contact surface maintenance and
greasing every time you open or close the housing.
※Please pay close attention and make sure the O-ring is not twisted or bulging, free of any
contaminants (dirt, hair, etc.), and that foreign objects do not obstruct proper closing of the
housing Back Cover, LCD Port or LCD Port Cover.
※DO NOT clean the housing with volatile organic solvents or chemical cleaning agents such
as thinner, gasoline, and benzine, etc.
※ousing Lens and LCD Port Window are manufactured using hard coat acrylic. When
cleaning use a clean soft cloth taking care not to scratch them.
SPECIFICATIONS
Compatible Camera SONY FDR-AX30/AX33/AXP33/AXP35
Maximum Depth 100 meters (328 ft.)
Material Main Body: Corrosion-resistant Aluminum Alloy, Anodized
Back Cover: POM
LCD Port (RVH-AXP35-LCD): POM
LCD Port Cover(RVH-AXP35-VF): POM
Lens, LCD Port Window, Viewfinder: ard Coat Acrylic
Levers, Buttons, Dials, Levers: POM, PVC
Screws, Springs, Shafts: Stainless Steel, Galvanized/SUS
Grip & Tray: Corrosion-resistant Aluminum Alloy, Anodized
Size
RV -AXP35-LCD
RV -AXP35-VF
Approx. W230mm x D225mm x 140mm ( ousing only)
Weight Approx. 2.4kg (Land )
130g (Freshwater w/Camera & Grip Assembly)
Approx. W140mm x D225mm x 140mm ( ousing only)
Weight Approx. 2.1kg (Land)
Accessories RECSEA Airlock Vacuum System (built-in) w/Gauge and Pump,
SONY RM-VPR1 Remote Controller (built-in), Camera Tray, Grip
& Tray Assembly, Reserve O-ring, SEATOOL O-ring Grease w/O-
ring Pick
14

INSURANCE INFORMATION
※We strongly recommend insuring your camera. For more information please contact your
dealer.
CONSUMABLE PARTS
※For replacement of consumable parts such as O-rings please contact your dealer or
Seatool/Recsea.
ORIGINAL RECSEA OPTIONS
The following items are optional. Please contact Seatool/Recsea or your local dealer if you
wish to purchase.
・RV -AXP35 LCD Port OP-AXP35
・RV -AXP35 LCD Port Cover OP-PC-AX35
・Dual Grip & Tray STG-05-AXP35-L (LCD)
・Dual Grip & Tray STG-05-AXP35-S (VF)
・RV -AXP35 O-ring Set
・O-ring Grease
AFTER-SALE SERVICE
Warranty period is two (2) years from purchase for general users, six (6) months for
commercial or industrial users. Seatool/Recsea will repair manufacturing defects free of
charge during the warranty period when product is used in accordance with this manual. This
warranty is only valid for housings purchased from authorized Seatool/Recsea international
dealers. This warranty does NOT cover nor does it include the SONY RM-VPR1 Remote
Commander. Damage to housing due to customer use, and for any consumable parts, the
repairs will be charged at normal rates. Shipping costs to and from dealer, or Japan if
necessary, shall be born by the customer for warranty and all other cases. This warranty
does not cover any damage to digital camera for any reason, including damage caused by
water intrusion. Please obtain insurance for all your equipment. Any repairs due to the
following will be charged at normal rates:
1) Repaired, modified or disassembled by person or company other than Seatool/Recsea;
2) If damaged in fire, natural disaster such as earthquake, flood, lightning, etc.;
3) Damage caused by dropping, impact, vibration;
4) When returned for warranty service not accompanied with Warranty Information copy, or if
Warranty Information is altered.
※Warranty does not cover any losses resulting from any malfunction of this product,
including those related to lost profits or any related expenses.
※Seatool/Recsea will stock parts necessary for repair for five (5) years from stop of
production.
※This product uses some degradable parts, such as buttons and O-rings. Seatool/Recsea
recommends overhauling the housing once per year, more frequently if used often.
Overhaul service is charged at normal rates.
15

MEMO

MEMO

MEMO

WARRANTY INFORMATION
Warranty Period One year from purchase
Purchase Date Year Month Day
Product Name SONY FDR-AX30/AX33/AXP33/AXP35 Waterproof ousing
Product Number □ RV -AXP35-LCD □ RV -AXP35-VF
Dealer Name
Serial Number
※Dealer: Stamp your company name and contact information, purchase date, model and serial
number.
Seatool/Recsea Manufacturing & Sales
NTF CORPORATION UN Division
390-1 Mii, Midori-Ku, Sagamihara-Shi
Kanagawa 252-0151, Japan
T: [phone] F: [phone]
http://www.seatool.net E-mail: [e-mail]