RiverRidge Ellsworth Tilt-Out Laundry Hamper 06-140 User manual

ASSEMBLY INSTRUCTIONS
ITEM #: 06-140 White
RiverRidge®Ellsworth Tilt-Out Laundry Hamper
ADULT ASSEMBLY REQUIRED
WARNING
SEE FULL WARNING ON PAGE 2
This product requires assembly by an adult because of small parts. Care should be taken
in unpacking and assembling this item to keep small parts away from children. During assembly
children should be kept away from the product due to possible risk of injury.
Young children can be seriously injured or killed if furniture tips over.
Don’t use this item for a TV stand or place heavy objects on top of item.
Always use angle-braces or anchors to secure furniture to the wall.

THIS UNIT WILL HOLD UP TO 25 POUNDS PER SHELF AND 15 POUNDS PER
CLOTH HAMPER OR A TOTAL OF 40 POUNDS. DO NOT LOAD EACH SHELF WITH
MORE THAN 25 POUNDS, EACH CLOTH HAMPER WITH MORE THAN 15 POUNDS
OR 40 POUNDS TOTAL WEIGHT. IF OVERLOADED WITH MORE THAN 25 POUNDS
PER SHELF, 15 POUNDS PER CLOTH HAMPER OR 40 POUNDS TOTAL WEIGHT,
SHELF MAY TIP FROM THE WALL AND CAUSE SERIOUS INJURY OR DEATH.

1
2
3
3
4
5
5
6
7
8
8
9
10
11
12
13
14
Hamper Front Door1PC
QTYNO DESCRIPTION
1
Hamper Back Panel1PC2
Hamper Side Panel2PCS3
Hamper Bottom Board1PC4
Hamper Support Bar2PCS5
Hamper Left Cross Bar1PC6
Hamper Right Cross Bar1PC7
Wooden Rod2PCS8
Cloth Hamper1PC9
Top Board1PC10
Left Side Panel1PC11
Right Side Panel1PC12
Bottom Board1PC13
Back Board1PC14
PARTS LIST

Wood Dowel
Cam Bolt
Cam Lock
Hamper Stopper
Hinge
Knob
Machine Screw (4x18mm)
2PCS
8PCS
8PCS
8PCS
1PC
1PC
2PCS
A
B
C
D
E
F
G
Screw (4x15mm)
Screw (4x10mm)
4PCS
1PC
H
I
Screw (4x30mm)
Screw (4x20mm)
1PC
20PCS
J
K
TOOLS NEEDED FOR ASSEMBLY: FLAT & PHILLIPS SCREWDRIVER (NOT INCLUDED)
THE USE OF A POWER SCREWDRIVER IS NOT RECOMMENDED FOR ASSEMBLY
DO NOT USE ITEM IF ANY PARTS ARE MISSING OR DAMAGED
PARTS LIST
NO PARTS QTY DESCRIPTION
Screw (3x12mm)
8PCS
L
Screw (2.5x10mm)
12PCS
M
Adjustable Anchor Bracket1PC
N
Plastic Anchor1PC
O
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.

STEP 1
STEP 2
STEP 3
F
F
LL
L
L
LL
E
E
E
G
G
JJ
J
J
JJ
JJ
II
II
1
1
5
5
3
3
6
7
1. Attach 2 hinges (E) to hamper front door (1) by inserting 4 screws (L) through holes on
hinges (E), then tighten to hamper front door (1).
2. Attach knob (G) to hamper front door (1) by inserting machine screw (F) through hole on
hamper front door (1), then tighten to knob (G).
1. Attach 2 hamper support bars (5) to hamper front door (1) by inserting 8 screws (J) through
holes on hamper support bars (5), then tighten to hamper front door (1).
1. Attach hamper left cross bar (6) to hamper side panel (3) by inserting 2 screws (I) through
holes on hamper side panel (3), then tighten to hamper left cross bar (6).
2. Repeat above step to assemble hamper right cross bar (7) to other hamper side panel (3).

STEP 4
STEP 5
J
J
J
J
J
J
J
JJ
J
J
J
33
3
3
4
22
6
7
1
3
3
1
1
1. Attach 2 hamper side panels (3) to hamper front door (1) by inserting 6 screws (J) through
holes on hamper side panels (3), then tighten to hamper support bars (5).
1. Slide hamper bottom board (4) into groove on hamper front door (1).
2. Attach hamper back panel (2) to hamper side panels (3) and hamper bottom board (4), make
sure hamper bottom board (4) slides into groove on hamper back panel (2).
3. Insert 6 screws (J) though holes on hamper side panels (3), then tighten to hamper back
panel (2).
5
5

STEP 6
STEP 7
11
12 A
A
A
A
11
12
13
BB
B
B
C
C
C
C
1. Screw 2 cam bolts (A) into cam bolt holes on left side panel (11).
2. Screw 2 cam bolts (A) into cam bolt holes on right side panel (12).
1. Insert 4 wood dowels (C) into wood dowel holes on left side panel (11) and right side
panel (12).
2. Attach bottom board (13) to left side panel (11) by inserting cam bolts (A) into cam lock holes
and inserting wood dowels (C) into wood dowel holes on bottom board (13).
3. Insert 2 cam locks (B) into cam lock holes, then rotate clockwise to secure cam bolts (A)
in place.
4. Repeat above steps to assemble right side panel (12) to bottom board (13).

STEP 8
STEP 9
11
12
13
A
AA
N
NA
B
B
B
B
H
H
10
10
C
CC
1. Screw 4 cam bolts (A) into cam bolt holes on top board (10).
2. Attach adjustable anchor bracket (N) to top board (10) by inserting 1 screw (H) through hole on
adjustable anchor bracket (N), then tighten to top board (10).
1. Insert 4 wood dowels (C) into wood dowel holes on top board (10).
2. Attach top board (10) to left side panel (11) and right side panel (12) by inserting wood
dowels (C) into wood dowel holes and inserting cam bolts (A) into cam lock holes on left side
panel (11) and right side panel (12).
3. Insert 4 cam locks (B) into cam lock holes on left side panel (11) and right side panel (12),
then rotate clockwise to secure cam bolts (A) in place.

11
12
STEP 10
STEP 11
10
13
L
L
LE
E
E
3
7
1
12
10
M
M
M
MM
M
M
M
M
M
M
M
3
14
7
1
1. Attach assembled hamper to outside cabinet by inserting 4 screws (L) through hinges (E),
then tighten to bottom board (13).
1. Attach back board (14) to back of cabinet by inserting 12 screws (M) through holes on back
board (14), then tighten to back of cabinet.

11
12
STEP 12
STEP 13
N
10
K
O
K
O
11
10
1D
D
D
3
1
6
1. Insert 2 hamper stoppers (D) into holes on left side panel (11) and right side panel (12).
Option #1: Securing to Drywall
1. Position cabinet against wall in desired location. Using a pencil, make 1 small mark on wall through
hole on bracket (N). Move cabinet away from wall and screw 1 plastic anchor (O) into wall on
pencil mark.
2. Place cabinet against wall, insert 1 screw (K) through hole on bracket (N), then tighten to plastic
anchor (O).
Option #2: Securing to Drywall and Wood Stud
1. Position cabinet against wall in desired location. Insert 1 screw (K) through hole on bracket (N),
then tighten through drywall and into wood stud.
*Tip: Anchor bracket (N) can be adjusted to correct distance from wall to cabinet as needed. Once
adjusted, be sure to re-tighten bracket inside cabinet for stability.
DRYWALL
WALL ANCHOR
WITH SCREW
SCREW
ONLY
DRYWALL
OPTION #2OPTION #1
WOOD
STUD
KK

STEP 14
9
8
89
9
3
3
11
11
10
10
1
1
1. Insert 2 wooden rods (8) through tabs on cloth hamper (9).
2. Place wooden rods (8) and cloth hamper (9) in cabinet as shown. Insert wooden rods (8)
into grooves on hamper side panels (3) to avoid movement.
IMPORTANT:
Keep assembly instructions for future reference.
ATTENTION ADULTS: Cabinet should be checked periodically for damage or loose
screws/parts. Take appropriate action necessary to correct hazards such as tightening
of screws and taking any damaged parts away from children.
CARE INSTRUCTIONS:
Wipe clean with a water dampened cloth. Wipe dry with clean cloth.
WARNING Please make sure your item is
secured to the wall, per assembly instructions.

Enjoy Your New RiverRidge®Hamper!
To order replacement parts at no cost to you, email [email protected], call
1-(844)-223-5201 or order parts online at www.riverridgehome.com. Only valid in the United States.
If purchased outside of the United States, please contact retailer where purchased.
Thank you for purchasing this RiverRidge® Home item. We hope you
enjoy it and consider purchasing other RiverRidge® items.
RiverRidge® is a registered trademark of Sourcing Solutions, Inc., Hudson, WI 54016