Serta USAN1022780-1 User guide

1
ORIGINAL INSTRUCTION MANUAL
DEAR CUSTOMER,
Thank you for choosing our product. Please read this manual carefully before assembling or using
the product, to avoid damage caused by improper use. If the product is passed on to third parties,
this manual should be passed on along with the product. If you have any questions, please don’t
hesitate to contact us.

2
TABLES OF CONTENTS
1.Wireless Remote Instruction---------------------------------4
2.Parts List---------------------------------------------------------7
3.Assemble the Frame-------------------------------------------10
WARNING

3
Specifications
Actuator rating: 24V,3A (Max)
Max.weight limit: 800 LBS
Dorsal angle: 0-70°
Leg angle: 0-45°

4
Wireless Remote Instruction
a.Brief introduction of remote control(W) panel function
and install the battery
Function analysis of six key
wireless key
S1 key: head up
S2 key: head down
S3 key: leg up
S4 key: leg down
S5 key: both up
S6 key: both down
The S1-S6 keys are inching
type, release to stop

5
installPlease thebattery(S) as shown,
pay attention to the battery polarity.
if you can't slide off the back covers smoothly , use hammer
slide down the
back cover
Install the battery slide up the
back cover
or other heavy stuff to knock the edge slowly.
I
U
WW

6
white slider block
then
b. Build connection
Attention: Can only be used in emergency situations!
Battery connector
Battery
c. If you encountered a power outage, you can install the
spare battery on the motor.
The spare battery can only be used to flat the frame
and MUST be removed after the frame got flat!
Before attaching motor to bed frame,
make sure the white slider block stays
invisible,If not,press the S6 button.
I
I
1. Press the 2 button on remote control at same time: head up, foot down.
2. Keep press the botton on reomote control and press the code match key
on motor.
3. When you hear "didi" sound, the match get succeed.
Now you can use remote control to lift and lower the bed.

7
A1 1×
LEFT FRONT RIGHT
RIGHT BED FOOT WITH LONG SCREW
BED FOOT WITH SHORT SCREW
FRONT
A2 1×
LEFT BACK
BACK
B1 1×
CROSS BEAM
B2 1× C 2× D 4×
E 2× F 2×
HEAD BAR
G 1×
LEFT LEG
H 1×
RIGHT LEG
I 1×
MOTOR
J 2×
DRIVINGLEVER
PARTS LIST

8
K 1×
HEAD BOARD BACK BOARD
L 1× M 1×
BOARD
Q
V 1×
INSTRUCTION MANUAL
W 1×
REMOTE CONTROL
X 1×
Cloth COVER
Y1 Y 2 Y 34×
M10*30
18×
M8*35
2×
M8*55
HIP
N 1×
FOUNDATION BOARD LEG BOARD
O 1× P 1×
BOARD FOOT
1×
RETAINER BAR
TAIL BOARD
T 1× U 1×
BATTERY

9
Y4
Y7 Y8 Y9
Y5 Y66×
M 8
2×
PLASTIC GASKET
1×
8MM SPANNER
1×
13MM OPEN END WRENCH
1× 4×
5MM SPANNER FINGER COVERS
Y10 4×
M 8*40

10
Please check that you have all the parts listed before you
do not continue assembly, please contact us immediately.
NOTE: Please do not tighten all the hardware completely
until the entire assembly is completed!
Assemble the Frame
1
A1
A2
B2
Y10
Y7 Y4
Y8
B1
Y10
Y7 Y4
Y8

11
E
D
D
D
C
C
Build Frame Base and Mount 6 Legs
2
D
E
A1
A2
B2
B1
The left and right brackets(A1,A2&B1,B2) are placed upside
down and placed symmetrically;
Round hole facing up( Part C)

12
H
F
J
3Build lift bars
The left and right bars(F,G,H) are connected with the driving lever,
lever(J), please align the arrows as indicated.
The head of two driving(J)
levers are aligned. F
JG

13
1
1
2
2
G
Foot
Head
B1 B2
4Connect Foot Lift bars on Frame Base
A1
A2
Y8
Y5
Y3
Y4 Y7
Assemble the circled part ,
pls check circle 1;
Assemble the square part,
pls check square 2.
Plastic
gasket
G
2
1
Y1
Y6
Y9

14
Assemble the circled part ,
pls check circle 1;
F
F
Head
Foot
B1
B2
A1
A2
5Connect Head Lift Bars on Frame Base
1
1
1
Y1
Y6
Y9

15
Head
Enfold the driving
lever into the motor Foot
2.Insert the motor into the driving lever, pplease ay attention
to the direction of the motor, check the mark head and foot.
Then buckle the back covers into place.
If the back covers don’t slide in,lift the driving lever until it
slides in.
6Mount motor
Put the motor slots
on the driving lever tube
I
1. Slide off the motor(I)
back covers.
II
J
J
Slide up
to close
IJ

16
7
Turn the bed frame over,then place the 7 bed boards in
the direction of the arrows and screw them with M8*35(Y2)
screws.
Mount bed boards
K
L
MN
O
PQ
Head
Foot
Y2
Y8
Y2

17
8Assemble the Frame
Push S6 button to flat the bed. Attach the velcro
tape of the cloth cover to the board.
Attention: Do not pull the face cover horizontally.
Before put on cloth cover, push S5 button till the bed elevate to the highest degree.
Startingattheendofthebed,cover the
left corner first.
Lift the cloth cover and pull up the cloth
cover till the board insert the cloth cover
completely as 2 and 3 in picture.
Cover the head of the bed as Step 1-3.
Spread out the cover and insert the board into
the edge of the right side cover.
1
3
2
4
3. Pull up the clothe cover till
the board compeletely insert
the clothe cover.
1. Place the board here first.
2. Lift the cloth cover.

18
X
Pay attention to the front
and back direction of the
cloth
cloth
cover; There are two
holes behind the cover.
Raise the head to put on the cloth cover, put down the head
after all the corner are wrapped.
9

T
Place remote
control
19
Push the retainerbar
At the end of the bed,push the retainerbar into the plastic
slider
Do not wash
Dry clean
Steam ironing
Do not twist dry
10