Servco DTR500 User manual

DOG TRAINING COLLAR WITH REMOTE
MODELS: DTR500, 502, 503, 1500, 1502, 1503
CONTENTS
The following items are included in the package, as shown on the photo below; dog training
collar(s), USB charger(s), USB wire(s), USB adapter(s), long probes pair(s).
PREPARING THE DOG TRAINING COLLAR WITH REMOTE FOR FIRST
TIME USE
The dog training collar needs to be charged for 5-6 hours. A fully charged battery provides an
autonomy of 20 hours. Connect the small USB adapter to the USB wire, and the USB wire to the
USB charger. Then, connect the charger to the dog training collar as it is shown on the photos
below. Lift the yellow rubber protective cover, and connect the charger. Now, switch on the dog
training collar. To switch it on, hold for 1 second the bottom part of the remote, where the built-in
magnet is (at the USB charging input), at the point where the indication light of the dog training
collar is. Then, remove the remote. In this way, the red indication light of the dog training collar is
constantly on, showing that the device is charging.

After 5-6 hours of charging, remove the charger. Then, switch off the dog training collar, by holding
the bottom part of the remote, for 4 seconds, where the built-in magnet is (at the USB charging
input), at the point where the indication light of the dog training collar is.
The remote needs to be charged for 4-5 hours. Connect the charger to the remote as it is shown on
the photo below.

PAIRING AND USE OF THE DOG TRAINING COLLAR WITH REMOTE
The dog training collar(s) sent to you already paired with the remote.
In case that you need to pair it again, do the following:
The remote can control up to 3 dog training collars. The remote has 3 pairs of buttons (pair 1, pair
2, pair 3).
Firstly, switch on the remote from the ON/OFF switch. Secondly, switch on the dog training collar.
When you have switched on the dog training collar, the indication light of the collar starts flashing.
Fourthly, hold the bottom part of the remote, for 10 seconds, where the built-in magnet is, at the
point where the indication light of the dog training collar is. Immediately, after this period, you
press the corresponding button (tone or shock&tone) of the pair you wish the dog training collar to
be saved. Then, a beep tone is heard, indicating successful pairing. Lastly, remove the remote. You
repeat the same procedure for the other collars you might have.
When you press the TONE button from the remote, a tone command is sent to the corresponding
dog training collar.
When you press the TONE&SHOCK button on the remote, a tone along with a SHOCK command
(stimulation) is sent to the corresponding dog training collar.
Each time you press the TONE or the TONE&SHOCK button, the corresponding LED1, or LED2
or LED3 flashes, indicating the sending of the commands. Furthermore, the LED at the top of the

remote flashes to indicate the sending of the commands.
The shock levels are adjusted by turning the rotary switch of the remote, from 1 until 8.
Level 1 is the lowest level and level 8 is the highest level.
After use, you can switch OFF the remote using the ON/OFF switch.
TIPS & FITTING OF THE DOG TRAINING COLLAR WITH REMOTE
The dog training collar with remote, is specially designed for hunting dogs and functions under hard
conditions (rain, dense vegetation). It has a lightweight durable design, and it is suitable for all
dogs, either small or big.
The dog training collar with remote, should be placed under your dog’s neck. The two probes
should touch the skin of your dog, so that your dog will receive the stimulation. The dog training
collar with remote should be fitted tightly to your dog’s neck. If your dog has a long fur, it is
advised to trim the fur a little, so the two probes can directly contact the skin of the dog.
You should find the correct stimulation level for your dog. You will start with level 1stimulation
(lowest). If you see no reaction by your dog, use level 2 stimulation. Increase the stimulation level
until you see a reaction. When you see a reaction, this is the correct stimulation level that you
should use.
If you use level 8 stimulation (highest), and you do not see any reaction by your dog, then the dog
training collar has not been fitted correctly. It should be fitted tightly on your dog’s neck. If your
dog has a long fur, you should trim a little the fur, at the place where the two probes contact the
skin.
Use the short or long probes provided depending on the dog’s fur.
It is advised to charge your dog training collar and the remote, prior to each use.
WARRANTY
We offer one-year warranty, and quick service after its end. The warranty does not cover the built-
in rechargeable battery of the collar and remote.