Sister Bay Hyannis MHYA-DCC-R User manual

2.75
F(8)
C(6)
(6)
(6)
D
1.50
A(16)
B(4)
3.50
E
(2)
2.75
G1
N
( Seat Base
Assembly) (Left side
Front & Rear Leg)
Do not use
any hand drill
on this product
ALLEN WRENCH
( included )
You will also need a phillips-head screwdriver
( not included )
WRENCH
( not included )
2.50
(8)
G
J
L
Arm
M
( Seat Bottom
Assembly )
I
K
(Under
Arm
brace )
(Right side
Front & Rear Leg)
H
( Seat Back Assembly )
Item No: MHYA-DCC - R
Hyannis Dining Counter Chair
Assembly Instructions
Item No: MHYA-DCB - R
Hyannis Dining Bar Chair
Hardware and Parts

Right side
Front Leg (FR)
(identification marks
facing up)
J
Under Arm
brace
G
FRONT
Right side
Rear Leg (RR)
(identification
marks
facing up)
J
1a - Attach part ( K ) under arm brace to part ( J ) front right side ( FR ) & Rear right side ( RR ) legs using 4 of screws.
( G ) 2 for each leg. Tighten screws using a phillips-head screwdriver. Be sure to lay the legs and arm brace on
a flat clean surface to assemble. Line up the front right leg ( FR ) with the front of the arm brace ( 2 screws ),
line up the rear right side leg ( RR ) with the back of the arm brace (1 screw). Make sure the identification marks
FR & RR are facing upward. Follow the same instructions for left side legs ( I ), the identification marks FL & RL
should be facing down. Leg and arm brace assembly should form an "A" frame if done correctly.
1b - To Attach part ( J ) , Right leg Assembly to part ( L ) arm, lay arm face down on a flat clean surface, place ( J )
right side leg assembly over the arm using ( 6 ) of screw ( A ) tighten screws using a phillips-head screwdriver.
Follow the same instructions for left side legs ( I ).
FR
RR
FR
RR
K
Right side
Rear Leg (RR)
(identification marks
facing up)
J
Right side
Front Leg (FR)
(identification marks
facing up)
J
Figure 1
Left side
Front Leg (FL)
(identification marks
facing down)
Under Arm
brace
FRONT
K
Left side
Rear Leg (RL)
(identification marks
facing down)
Left side
Rear Leg (RR)
(identification marks
facing down)
Under Arm
brace
FRONT
K
Left side
Front Leg (FR)
(identification
marks
facing down)
BACK
Arm
L
I
1b
1a
A
Under Arm
brace
FRONT
K
BACK
Arm
L
I
I
I
A
G

2b - Attach part ( H ) , seat back assembly , to part (M), seat bottom assembly , as shown in Figure1 see detail
2 using ( 4 ) of screws ( A ) , 2 on each side, tighten screws using a phillips-head screwdriver .
A
( Detail 2 )
( Detail 1 )
2a - Attach part ( H ) , Seat Back Assembly , to part (M), s eat bottom assembly you must align the lower front
edge of Yoke to hide the front edge of groove, see detail 1 .
front edge of groove
front edge of Yoke
M
( Seat Bottom Assembly )
( Seat Back
Assembly )
H
Figure 3
Figure 2
3a - Attach part ( J ) , Right side front and rear leg assembly , to assembly from Figure 2 as shown in Figure 3,
identification marks ( FR ) and ( RR ) facing inside towards the seat see detail 3, using ( 2 ) of joint connector
bolts ( B ), ( 2 ) washers ( C ), ( 2 ) lock washers ( D ), ( 2 ) hex nuts ( E ), see detail 4 tighten bolts using an allen
wrench and also an adjustable wrench follow the same instructions for left side front and rear leg assembly.
I
(Left Side
Front & Rear leg)
F
( Detail 5 )
( Seat Back
Assembly )
H
F
B
( Detail 4 )
J
B
BF
C
D
E
identification marks
(Right side
Front & Rear leg)
(FR) (RR)
( Detail 3 )
3b - Attach part ( I ), Left side front and rear leg and part ( J ), right arm leg assembly, to seat back assembly ( H ), as
shown in Figure 3, see detail 5, using ( 3 ) of lag screws ( F ), tighten screws using and allen wrench. Follow the
same instructions right side front and rear leg assembly.

Figure 4
4 - Attach part ( M ), seat base assembly ,to assembly from Figure 2 as shown in Figure 4 see detail 6 , using ( 4 ) of
joint connector bolts ( G1) , ( 4 ) washers ( C ), ( 4 ) Lock washers ( D ) and ( 4 ) hex nuts ( E ), tighten bolts using an
allen wrench and also an adjustable wrench.
M
( Seat Base)
Assembly
( Detail 6 )
G1
E
D
C
G1
F
F
CARE AND MAINTENANCE
To clean your product, use mild soap and water. For heavy soil build-ups use any non-abrasive household cleaners
or ask your Sales Representative about Sister Bay Furniture Cleaner.
Please contact our Customer Service Department for assembly assistance, questions or replacement parts at 1-866-947-7632
or email [email protected]. Our Customer Service Department is available Monday - Friday from 8:30 a.m. to 4:30 p.m. EST