spaxo Norefjelll User manual

USER MANUAL
PLUG & PLAY
spaxo.no
Norefjell
SPX-01
Hvaler
SPX-02
Tjøme
SPX-03

23
NOW IT IS TIME FOR YOU TO
SIT BACK AND ENJOY!
Congratulations for investing in your own
health & lifestyle!
Thank you for your trust in the Norwegian
premium wellness-brand SPAXO. We hope
you get to spend as much time as possible
relaxing in your premium quality home
spa! But rst we recommend you to read
this user manual.
PRECISE EXECUTION OF
EVERY DETAIL
We work with the latest technology and
machinery, currently also used in auto-
motive, aircraft and arms industry. That
enables us to be precise to a hundredth
of a millimeter. Precision and quality are
areas which we never compromise in.
WE ALWAYS CHOOSE THE
GREEN WAY
Instead of using shell lamination which
creates harmful styrenes as a by-product,
we use high quality GreenShield mate-
rials. They are completely harmless to
both health and nature. On top of that
we recycle all of the leftover material
and introduce it back to the manufac-
turing process. That makes us a close to
zero-waste company (97%).
STRICT QUALITY TESTING
BEFORE SHIPMENT
Not one hot tub leaves our manufacture
hall without a series of strict and thorou-
gh testing procedures. We test all our
products in real life circumstances which
allows us to eliminate 99% of possible
defects and malfunctions. We are also
inspired by the hardline quality control of
TPS (Toyota Production System).
Modern manufacturing Modern manufacturing
Welcome to
a World
of Wellness

45
Table of content Hot tub performance specifications
1 Hottubperformancespecications . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Preparation for the installation of the hot tub . . . . . . . . . . . . . . . . . . . 6
2.1 Preparation of the place for installation and connection to electricity . . . . . . . 6
2.2 Preparation for the interior hot tub installation . . . . . . . . . . . . . . . . . . . . . 6
2.3 Preparation for the exterior hot tub installation . . . . . . . . . . . . . . . . . . . . . 7
3 Installation of the hot tub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Filling the hot tub with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Running the power supply of the hot tub . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.4 Programming of the hot tub control unit using the control panel . . . . . . . . . . 8
4 Aquatic AV audio system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Main displayed data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2 Temperature setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.3 Filter time setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.4 Mode setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.5 Jets control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.6 Lights control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7 Upkeep of the hot tub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
7.1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.2 Removalandcleaningoftheltercartridge. . . . . . . . . . . . . . . . . . . . . . . 15
7.3 Maintaining the quality of the water in the hot tub . . . . . . . . . . . . . . . . . . 15
7.4 Replacing the water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.5 Cleaning the outer shell of the hot tub . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.6 Hot tub hygiene and disinfection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.7 Thermo cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.8 Upkeep of the thermo cover and upkeep instructions. . . . . . . . . . . . . . . . . 18
8 Winter and summer time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8.1 Winter time – using the hot tub, all year operation (SLP) . . . . . . . . . . . . . . . 19
8.2 Summer time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9 Final establishments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
9.1 Guarantee conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9.2 Safe disposal of the product after the service life . . . . . . . . . . . . . . . . . . . 19
9.3 Warranty claims and repair services . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
10 Repair services chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
11 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
1 Hot tub performance specifications
Performance specifications
nominal voltage: one phase 220-250 V 50/60 Hz
maximum work current: 1 × 16 A
voltage resistance: 1 250 V/min. without puncturing
insulation resistance: >=200MΩ
water resistance: IPX5
electrical shock protection: rstlevel
Stress load
heating: 230 V/2 kW/13,6 A
ozone: 230 V/50–60 Hz /80 mA
circulation pump 1/2: 2,2 kW
overall wattage (depends on the hot tub type): 4,5 kW / h
protection class: I.
lighting: LED 12 V/10 W
humidity resistant speakers: yes
For your own safety and the safety of your device, please comply with the
following instructions. Read the following instructions carefully and comply with
them during the use of the hot tub to prevent damage and risk of an injury.

67
Preparation/Installation of the hot tubPreparation for the installation of the hot tub
2 Preparation for the installation of the
hot tub
Check the hot tub first before the installation. Immediately contact the
seller in case any of the parts are broken or missing.Make sure that all the
components correspond to your order
. Check the hot tub before every use. In
case of any damage, do not use the hot tub.
2.1 Preparation of the place for installation and connection to
electricity
The hot tub must be installed on a at and rm enough base plate with regard to
the maximum load of the construction. For exterior installations we recommend a
construction of a monolithic concrete base plate of minimum thickness of 10 cm. It is
always necessary to pick the maximum load of the base plate with regard to the size
and weight of the hot tub. Consult with your construction supervisor. The weight is
adduced in the technical description of the hot tub.
2.2 Preparation for the interior hot tub installation
If the hot tub is installed in an interior space, it is necessary to comply with safety
instructions. The basic safety requirements are mainly non-skid oors and drainage
in the place of the installation in case of a water overow. It is also crucial to keep in
mind that the humidity around the hot tub will rise and can damage surrounding
electric appliances. Therefore we recommend customizing the place of the installation
according to these conditions. The hot tub should be accessible from all sides for
future repair services. If it is not suciently accessible during the guarantee period,
the owner has a duty to ensure the access.
2.3 Preparation for the exterior hot tub installation
If the hot tub is installed in an exterior space, it is necessary to comply with safety
instructions. The basic safety requirements are mainly non-skid oors and water
drainage in case of a rainfall or water overow from the hot tub. Therefore we
recommend customizing the place of the installation according to these conditions.
3 Installation of the hot tub
3.1 General information
a) Carefully remove all the packaging material from the hot tub and position the hot
tub on a beforehand selected place of installation.
b) Every hot tub is tested in real life conditions during the production process,
therefore there is a possibility some technical parts of the hot tub have remained
slightly dirty. We recommend you to clean the surface of the hot tub using a
suitable method; lukewarm water works best for this purpose. Clean the surface
using a soft cloth only. Don't use any rough abrasive means and cloths which could
permanently damage the surface of the hot tub. If you decide to use a generic
cleaning detergent, it cannot be aggressive towards the hot tub surface.
3.2 Filling the hot tub with water
Fill the hot tub with a sucient amount of water. The level of water in the hot tub
cannot ever fall under the skimmer level. If you notice a water leak, stop the water
until the defect is xed. Hot tubs do not possess the technology for water-softening
and hard water can be damaging to them. The damages caused by poor handling and
upkeep are not covered by the guarantee.
a) Fill the hot tub through a skimmer to prevent an over aeration of the circulation
pumps.
b) Do not ll the hot tub with water of temperature over 40 °C.
c) Once the water reaches the desired level, put the cartridge lter inside the
skimmer. Tilt the lter during the installation to prevent air bubbles. Only after
removing the air from the lter, install the lter into place.
NOYES

89
5.2 Temperature setting
Set the temperature with the up or down arrows. Use the arrow to set the desired
temperature, the value  ashes, and then save itself.
5.3 Filter time setting
You can access the  ltration settings by pressing the down arrow and the JETS button.
Fis displayed and the numeric value represents the clock. Set the time by arrfows, the
 lter will run (1–8 hours) – the value will  ash and then save itself. The  lter cycle is
repeated every 12 hours. If the electricity supply is interrupted,  ltration needs to be
re-set.
5.4 Mode setting
To set the water heating mode in the hottub, press the down arrow and the LIGHT
button. Each time you repeat, the mode switches.
Mode settings options:
Standart (St) heating the water to the set temperature
Ekonom (Ec) heating the water only during  ltration
Sleep (SL) heating the water by 10 °C below the set temperature
Control panelInstallation of the hot tub/Audio system Aquatic
3.3 Running the power supply of the hot tub
If the hot tub is connected by a moving supply cable, this cable cannot come in contact
with sharp objects or be exposed to external forces. Therefore we recommend putting
the supply cable inside a protective case. Turn on a residual current device intended
for a hot tub.
3.4 Programming of the hot tub control unit using the control
panel
Now you can start the programming of the hot tub. The process is described in the
chapter “Control panel”. After you are  nish the programming, cover the hot tub with
a thermo cover and let the water temperature to stabilize. Check the water level
inside the hot tub regularly.
4 Aquatic AV audio system
Aquatic AV audio system AQUATIC/MY MUSIC (relevant only for hot tubs equipped
with the system)
If you want to play music from an external device, it is necessary to pair the device
with the hot tub  rst (phone, tablet, computer). Turn on the bluetooth system on your
external device and search for the AQUATIC device. The connection is not restricted by
a code and only one connection can be active at a time. You can play music immediately
after the devices are successfully paired. You can control all the functions of the audio
system on your connected external device.
5 Control panel (BALBOA VL401)
5.1 Main displayed data
LIGHT COOL
HEAT
WARMJETS
0.340”
Overlay Graphics Template (xx401)
Use this to create overlay graphics only. Do not use this template to create a die cutting tool.
PROPRIETARY AND CONFIDENTIAL
THIS DRAWING CONTAINS INFORMATION WHICH IS THE PROPRIETARY
PROPERTY OF BALBOA WATER GROUP. REPRODUCTION IN WHOLE OR IN
PART WITHOUT EXPRESS WRITTEN PERMISSION IS PROHIBITED.
LIGHTJETS COOL
HEAT
WARM

10 11
Control panel/Trouble shooting
5.5 Jets control
Press the JETS button to turn on the jets
5.6 Lights control
Press the LIGHT button to turn on the lights. Every time the light is switched o and on
again, the color changes. The range of colors is varied.
Trouble shooting
6 Trouble shooting
message meaning action required
no message
on display
Power has been cut off to the
spa.
The control panel will be disabled
until power returns. Time of day
will be preserved for 30 days with a
battery back-up on EL8000 and EL5000
systems. EL1000 and some EL2000
systems reset the time of day on each
power-up. Spa settings are preserved
on all systems.
OHH
“Overheat” – The spa has shut
down.* On some systems, an
alarm may sound. One of the
sensors has detected 118 °F
(approximately 47.8 °C) at the
heater.
DO NOT ENTER THE WATER. Remove
the spa coverand allow water to cool.
Once the heater has cooled, reset by
pushing any button. If spa does not
reset, shut o the power to the spa and
call your dealer or service organization.
OH5
“Overheat” – The spa has shut
down.* One of the sensors has
detected that the spa water is
110 °F (approximately 43.3 °C).
DO NOT ENTER THE WATER. Remove
the spa cover and allow water to cool.
At 107 °F (approximately 41.7 °C), the
spa should automatically reset. If spa
does not reset, shut o the power to
the spa and call your dealer or service
organization.
message meaning action required
ICE “Ice” – Potential freeze
condition detected.
No action required. The pumps and
the blower will automatically activate
regardless of spa status.
SnA
Spa is shut down.* The sensor
that is plugged into the Sensor
“A” jack is not working.
If the problem persists, contact your
dealer or service organization. (May
appear temporarily in an overheat
situation and disappear when the
heater cools.)
Snb
Spa is shut down.* The sensor
that is plugged into the Sensor
“B” jack is not working.
If the problem persists, contact your
dealer or service organization. (May
appear temporarily in an overheat
situation and disappear when the
heater cools.)
SnS
Sensors are out of balance.
If this is alternating with the
temperature, it may just be a
temporary condition. If the
display shows only this message
(periodically blinking), the spa is
shut down.
If the problem persists, contact your
dealer or service organization.
HFL
A substantial dierence
between the temperature
sensors was detected. This
could indicate a ow problem.
Check water level in spa. Rell if
necessary. If the water level is okay,
make sure the pumps have been primed.
Press any button to reset.
LF
Persistent low ow problems.
(Displays on the fth occurrence
of the “HFL” message within
24 hours.) Heater is shut
down, but other spa functions
continue to run normally.
Follow action required for “HFL”
message. Heating capacity of the spa will
not reset automatically; you may press
any button to reset.
dr Inadequate water detected in
heater.
Check water level in spa. Rell if
necessary. If the water level is okay,
make sure the pumps have been primed.
Press any button to reset.
DIAGNOSTIC MESSAGES
* On some systems even when spa is shut down, some equipment may occasionally turn on to
continue monitoring temperature or if freeze protection is needed. * On some systems even when spa is shut down, some equipment may occasionally turn on to
continue monitoring temperature or if freeze protection is needed.

12 13
Trouble shootingTrouble shooting
message meaning action required
dry
Inadequate water detected
in heater. (Displays on third
occurrence of “dr” message.)
Spa is shut down.
Follow action required for “dr ” message.
Spa will not automatically reset; you may
press any button to reset.
Pr When your spa is rst actuated,
it will go into Priming mode.
See the M-7 Installation Instruction
Manual for complete instructions
on Power-up and Pump Priming.
The Priming mode will last for up
to 4 minutes and then the spa will
begin to heat and maintain the water
temperature in the Standard mode.
Temperature unknown.
After the pump has been running for
1 minute, the temperature will be
displayed.
Sby
Standby Mode has been
activated by pressing a button
combination on the user panel.
Press any button, except “Jets”, to leave
Standby Mode and return to normal
operation.
Std The spa is operating in Standard
Mode.
Temperature display is current after
pump has been running for at least 2
minutes.
Ecn The spa is operating in Economy
Mode.
“Ecn” will appear solid on the display
when the temperature is not current.
“Ecn” will alternate with the temperature
when the temperature is current.
SE The spa is operating in
Standard-in-Economy Mode.
Operates the same as Standard mode,
then reverts to Economy mode after
1 hour. Press “Temp” followed by “Light”
to switch directly to Economy mode.
SLP
Sleep Mode has been
activated by pressing a button
combination on the user panel.
“SLP” will appear solid on the display
when the temperature is not current.
“SLP” will alternate with the temperature
when the temperature is current.
PHL pH is low Add pH increaser according to
manufacturer’s instructions.
message meaning action required
PHH pH is high Add pH reducer according to
manufacturer’s instructions.
SAL Sanitizer is low. Add sanitizer according to
manufacturer’s instructions.
SAH Sanitizer is high. Remove spa cover and allow sanitizer to
dissiwpate.
drn The pump is on during Standby
Mode to assist in draining the spa.
Press “Jets” to turn o the pump when
water has drained (or power o the spa.)
rtC Hardware failure. Contact your dealer or service
organization.
PSt Hardware failure.
Contact your dealer or service
organization if message appears on
more than one power up.
CrC Firmware install problem.
Contact your dealer or service
organization if message appears on
more than one power up.
CFE Conguration error. Spa cannot
start up.
Contact your dealer or service
organization.
9F 1 Spa could not trip GFCI.
Contact your dealer or service
organization. Continued operation may
be unsafe.
StU
A pump appears to be stuck on,
causing the water temperature
to creep up, possibly to
hazardous levels.
POWER DOWN SPA IMMEDIATELY. DO
NOT ENTER THE WATER. Contact your
dealer or service organization.
HOt
A pump appears to have been
stuck on the last time spa was
powered.
POWER DOWN SPA IMMEDIATELY. DO
NOT ENTER THE WATER. Contact your
dealer or service organization.

14 15
Upkeep of the hot tubTrouble shooting
7 Upkeep of the hot tub
7.1 General information
Do not expose the hot tub to sun without water inside or a cover on top. The direct
sunlight can cause fading and deformation of the surface material. When you are not
using the hot tub, cover it with the thermo cover, regardless of whether it is empty
or full. Protect the hot tub from rain and snow. Place the hot tub under a gazebo or a
roof if possible.
a) Do not open the control unit. There are no user-xable parts inside.
b) Drain, clean and ll the hot tub with clean water on regular schedule.
c) Clean the lter cartridge at least once a week.
d) The hot tub user should have a proper shower before and after the use of the
hot tub.
7.2 Removal and cleaning of the filter cartridge
The hot tub lter cartridge can get clogged by calcareous and mineral particles from
a hard water, which can lead to a restricted water ow inside the ltration system.
We recommend to clean the filter cartridge at least once a week.
Remove the cartridge and the skimmer insertion. Using a garden hose, clean the
cartridge so that no settled dirt remains in the corners of the lter. Once clean, put
the insertion back to the skimmer. Put the cartridge inside the skimmer tank next
and close it. Remember that the lter cartridge has to be replaced every 3– 6 months.
Replace it even sooner if it is damaged or clogged, it is not usable in such state.
Make-up, sunscreens and other types of body lotion decrease the quality of the
water and lower the lter cartridge longevity.
7.3 Maintaining the quality of the water in the hot tub
WARNING: Always add the chemicals to the water, never the other way around.
Add the chemicals to the water only when there are no people inside. Use the
circulation pumps to mix the chemicals with the water. Store the chemicals
according to the instruction on their label.
message** frequency*** action required
rPH every 7 days Test and adjust pH chemical levels per
manufacturer’s instructions.
rSA every 7 days Test and adjust sanitizer chemical levels
per manufacturer’s instructions.
rCL every 30 days Remove, clean, and reinstall lter per
manufacturer’s instructions.
rt9 every 30 days Test & reset GFCI per manufacturer’s
instructions.
rdr every 90 days Drain and rell spa per manufacturer’s
instructions.
rCO every 180 days Clean and condition cover per
manufacturer’s instructions.
rtr every 180 days Clean and condition wood per
manufacturer’s instructions.
rCH every 365 days Install new lter.
rCA as needed Install new Mineral cartridge.
PERIODIC REMINDER MESSAGES
(Press the “Temp/Warm” button to reset a displayed reminder.)*
* User can suppress all reminders in User Preferences.
** All of these Periodic Messages can be disabled individually by the spa manufacturer.
*** The producer can change the frequencies as required.

16 17
Upkeep of the hot tubUpkeep of the hot tub
a) Use a suitable water hardness regulator regularly (the HANSCRAFT SPA
Water hardness regulator is recommended) and follow the instructions on the
chemicals‘ label.
b) Depending on the frequency of use of the hot tub, test the water quality
regularly by a suitable water quality tester.
c) Adjust the water pH level accordingly by suitable water chemicals
(the HANSCRAFT SPA – pH PLUS and pH MINUS is recommended).
d) Adjust the Cl (chlorine) level with suitable water chemicals (HANSCRAFT SPA
– MULTI MINI 3 in 1 tablets are recommended). Follow the instructions on the
chemicals‘ label.
For the chlorine to have the desired effect, the pH level needs to be
adjusted first.
e) We recommend you to clean/replace the lter cartridge before adding the
chemicals.
Chlorine shock – in case of extreme pollution, it is necessary to treat the water with
a dose of fast dissolving chlorine and thus perform a chlorine shock. The pH level of
the hot tub water has to be adjusted to 7.0 –7.6 rst and the chlorine level has to be
checked. Once a week or after adding a large amount of fresh water to the hot tub,
add a shock dose of chlorine 10–20 g/m3(2 table spoons) into the water. Add the
chlorine only when there are no people in the hot tub. After you add the chlorine,
turn on the circulation pumps so that the chemicals mix well with the water. If you are
using a granulated form of the chemical, dissolve it in a small amount of water rst.
Let the chlorine level drop to 3 mg/l before you start using the hot tub.
Oxygen shock – in case of extreme pollution, it is necessary to treat the water with a
large dose of fast dissolving oxygen and thus perform an oxygen shock. The pH level
of the hot tub water has to be adjusted to 7.0–7.6 rst and the oxygen concentration
in the water has to be checked. Once a week or after adding a large amount of fresh
water to the hot tub, add a shock dose of oxygen (2 tablets) into the water. Add the
oxygen only when there are no people in the hot tub. After you add the oxygen,
turn on the circulation pumps so that the chemicals mix well with the water. Let the
oxygen level drop to 15 mg/l before you start using the hot tub.
Store the chemicals according to the instructions on the label.
7.4 Replacing the water
It is important to keep the hot tub water fresh and clean. We recommend you to
replace the water at least every 3 months unless the water quality drops sooner. The
hot tub water can be used for watering the garden for example, given that it has not
been chemically treated at least one week prior.
a)
Disconnect the hot tub from the power supply (turn o the residual current device).
b) Check the power supply cable and make sure it is not wet.
c) Drain the water through a water drainage system, close it carefully and ll the
hot tub with fresh water.
d) Connect the hot tub back to the electrical circuit (turn on the residual current
device).
7.5 Cleaning the outer shell of the hot tub
Use a mild, not abrasive cleaning detergent and a soft cloth.
7.6 Hot tub hygiene and disinfection
Taking care of hygiene is extremely important for elimination of any germs, algae and
other harmful organisms polluting the water in the hot tub. Test the water using the
testing kit rst (to nd out the pH and Cl level) and follow by using suitable water
chemicals accordingly. Follow the instructions on the chemicals‘ label carefully.
7.7 Thermo cover
Using the thermo cover helps saving up energy expenditures by minimizing
temperature loss and evaporation. The cover is an eective way of protecting your
hot tub from impurities and fallen leaves.
WARNING: For safety and damage prevention reasons, do not sit, stand or lie
on top of the cover. Do not place any objects on top of it. The thermo cover
does not serve as a fence around the bathing area either. Do not let animals
walk on top of the thermo cover. Prevent a large snow layer build up on top of
the thermo cover.
Ideal chemical levels
Free chlorine concentration
(active oxygen concentration)
0.7–1.0 mg/l
(10–15 mg/l)
pH level 7.0 –7.6
Calcium 100–180 mg/l
Overall alkalinity 80–120 mg/l

18 19
8.1 Winter time – using the hot tub, all year operation (SLP)
If you decide to keep using the hot tub during the winter time, it is necessary to
keep checking the hot tub for cases of for example: circuit break failure, motor not
working, heating not working, lter cartridge getting clogged.
If the instructions above are not complied with and it results in a damage of
the hot tub, the warranty cannot be claimed.
8.2 Summer time
Do not expose the hot tub to direct sunlight; do not use inappropriate cleaning
detergents for upkeep. Prevent the hot tub surface coming in direct contact with
chemicals as well as surface scratches cause by sharp objects. Ensure the safety of
children in the hot tub by a continuous adult supervision. Only eligible persons over
18 years of age, educated about the whole process, can be operating the hot tub. The
same goes for handling the water chemicals, which have to be stored out of children’s
reach.
9 Final establishments
9.1 Guarantee conditions
Guarantee conditions abide by terms and conditions of your distributor.
9.2 Safe disposal of the product after the service life
Hire a professional service to dispose of the hot tub after it reaches the end of its
longevity. According to the WEEE directive (Electronics and electrical appliances
waste) this device cannot be disposed of like a regular waste.
9.3 Warranty claims and repair services
Potential warranty claims abide by the consumer protection laws and the warranty
claims policy of your distributor.
Winter and summer time/Final establishmentsUpkeep of the hot tub/Winter and summer time
7.8 Upkeep of the thermo cover and upkeep instructions
It is important to take a proper care of the thermo cover: clean it when necessary
and treat it with a product intended especially for an eco-leather or fake leather. The
guarantee does not cover damages caused by an inappropriate cleaning product.
a) The right balance of water chemicals represents an important factor in prolonging
the longevity of your hot tub thermo cover.
b) Remove the hot tub's cover and place it on the ground surface down.
c)
Wash the cover with a large amount of water from a garden hose or a water bucket.
d) Clean the thermo cover surface using a soft brush and a mild dish soap solution
(1 tea spoon of dish soap per 8 litres of water).
Attention: Do not let the dish soap solution dry on the thermo cover before
washing it off!
e) Wash o the cleaning solution thoroughly.
f) Return the cover back on the hot tub.
g) Open the thermo cover regularly so that the chemical vapours can disperse. Flip
the thermo cover inner side u at least twice a year for 3–4 hours.
h) If the thermo cover does not get regularly cleaned twice a month, the surface
material can become frail or age prematurely. The seams can separate. If you do
not clean the thermo cover appropriately, the guarantee becomes invalid.
WARNING: Do not lift the thermo cover by the handles. A vacuum forms between
the thermo cover and the hot tub therefore lifting by the handles could result in
a damage. It is necessary to support the thermo cover from below by hand.
8 Winter and summer time
Winterizing the hot tub, a process recommended by the producer.
It is required that all water gets drained from the hot tub during the process of
winterizing it, as well as water from all the technical parts of the hot tub (circulation
pumps, pipes, etc.) We recommend you to use our specialized service for this purpose
because awed winterizing of the hot tub can result in a loss of the guarantee. If
you decide to use our professional services, it is necessary to order them sucient
amount of time in advance. In case of winterizing the hot tub by yourself, it is crucial
to do it when the air temperature is still above zero. If the winterizing is done in
temperatures below zero, it can be very dicult because water in the motors could
have frozen already and damaged some parts of the hot tub.

20 21
Repair services chart/Notes Notes
10 Repair services chart
11 N o t e s
A TABLE FOR YOUR NOTES, PLEASE FILL OUT THE FOLLOWING
INFORMATION. You will need the filled out information in case of a repair
requested through the customer service line.
Purchase date
Delivery date
Model name
Serial number
Seller information
(name, phone number)

22 23
Notes Notes

Edvard Griegsvei 1
1410 Kolbotn
40 08 08 40 | [e-mail] | spaxo.no