STC SPACE SAVER 30324 User manual

M o u n t i n g S y s t e m s
Installation Manual model # 30324
Fits Displays 13” to 32’’
Supports Up to 50 lbs (23 kgs)
Dual Arm Tilt/LCD Mount
Systems Trading Corporation
450 7th Avenue Suite 2809, New York, NY 10123
Phone: [phone] Toll Free: [phone] Email: [email protected]
Meets VESA Standards 50/75/100, 100x200, 200x200
Projection from Wall from 3” to 17”
M o u n t i n g S y s t e m sM o u n t i n g S y s t e m sM o u n t i n g S y s t e m sM o u n t i n g S y s t e m s
M o u n t i n g S y s t e m s

!
!IMPORTANT WARNINGS AND CAUTIONS!
TABLE OF CONTENTS
1 of 12
www.stcny.com
warnings and cautions ......................................................................
unpack ..............................................................................................................
required tools ......................................................................................
identify display back style, screw diameter and depth ........
attach to VESA 50, 75 and 100 .........................................................
add extension wings ..........................................................................
attach to larger displays ....................................................................
wall placement .....................................................................................
attach to wood stud ...........................................................................
attach to masonry walls ....................................................................
mount display to wall plate ...............................................................
secure ........................................................................................................
adjust ........................................................................................................
warranty ...................................................................................................
1
2
2
3
4
5
6
7
8
9
10
10
11
12
!
!A WARNING alerts you to the possibility of serious injury or death if you do not follow the
instructions.
A CAUTION alerts you to the possibility of damage to or destruction of the equipment if you
do not follow the corresponding instructions.
Failure to provide adequate structural strength for this component can result in physical
injury and damage to the equipment. It is the installer’s responsibility to make sure the
structure to which this component is attached can support four times the combined weight
of all equipment. Reinforce the structure as required before installing the component.
Improper installation can result in serious physical injury. This mount has been tested to
support 50 lbs (23 kgs.) Do not exceed that weight.
Safety measures must be observed at all times during the installation of this product. Use
proper safety gear and tools during the installation process to prevent physical injury.
Do not install on a structure that is prone to vibration, movement or chance of impact.
Doing so could result in damage to the at panel display and/or mounting surface.
Do not install near a heater, replace, direct sunlight or any other source of direct heat.
Doing so could result in damage to the at panel display and could increase the risk of re.
WARNING:
WARNING:
WARNING:
WARNING:
CAUTION:
CAUTION:
CAUTION:
BEFORE YOU BEGIN, MAKE SURE YOU CAREFULLY READ AND UNDERSTAND THE INSTRUCTIONS IN THIS
MANUAL. This bracket system incorporates a slide mount design. Our goal is to make this installation
easy for you. Please follow the instructions in the order presented in this manual and be sure to observe
all warnings and cautions.

required tools
unpack
M4 x 12mm screw, lock washer and washer
Make certain the following installation hardware and components are included. If any of the parts are missing or
damaged please contact STC Customer Care at [phone].
Parts are not shown actual size.
M4 x 30mm screw, lock washer and washer
M5 x 12mm screw, lock washer and washer
M5 x 30mm screw, lock washer and washer
M4/M5 large spacer
4 x
stud nder
phillips screw driver
2
1
tape measure
safety glasses
pencil
power
drill
5/32” (4mm) wood drill bit
or
1/4“ (6mm) + 3/8” (10mm) masonry drill bits
lag bolt and washer nylon anchor
2 of 12
www.stcny.com
M4 x 8mm screw to connect
wings to VESA mount
8 x
M4 x 8mm safety screw
allen key
1 x
right extension wing
left extension wing
wall plate dual arm tilt VESA mount
1 x
!The dual arm tilt VESA mount is shipped with the plate attached with the safety screw.
Remove the safety screw and wall plate. They will be attached to the mount in step 9.

1identify
mounting pattern
measure depth
!Unplug your display before you begin.
Invert the display and place it on a soft, padded, at surface.
at
recessed
Mark a toothpick or straw.
200
200
200
100
100
100
75
75
OR
Gently test all fasteners together, screwing them in by hand
to ensure proper t. Do not tighten. If there is any resistance,
remove immediately and select alternate fasteners.
!
OR
test
2
To ensure proper mounting of the brackets to your display, we have provided several sizes of screws and
spacers that can be used in combination. Combinations are determined by the display back style (the area
surrounding the mounting holes) and the diameter and depth of those holes.
VESA patterns 75 and 100 use M4 screws.
VESA patterns 100 x 200 and 200 x 200 use either M4 or M5 screws.
NOTE: Measure with spacer for displays with recessed backs.
M4
M5
M4
3 of 13
www.stcny.com

3
VESA 75 x 75
VESA 100 x 100
attach to VESA 50, 75 and 100
!Tighten screws so mount is rmly attached to the display.
DO NOT OVER TIGHTEN. Over tightening may damage your display.
4 of 12
www.stcny.com
Place spacer directly on mounting
holes of recessed display back.
OR
M4
M4
75
75
VESA 50 x 50
50
50

4add extension wings
M4 x 8mm screw
8 x
Use eight M4 x 8mm screws to attach extension wings to mount.
!Tighten screws so wings are rmly attached. DO NOT OVER TIGHTEN.
Over tightening can damage screws, greatly reducing holding power.
5 of 12
www.stcny.com
Extension wings have threaded inserts.

5attach to larger displays
VESA 200 x 200
VESA 100 x 200
Place spacer directly on mounting
holes of recessed display back.
M4
M4
OR
M5
M5
OR
OR
!Tighten screws so mount is rmly attached. DO NOT OVER TIGHTEN.
Over tightening may damage your display.
6 of 12
www.stcny.com
100
200
200
200

6wall placement
Wall Placement:
When selecting a wall to mount your display, keep the following in mind:
• Select a place with easy access to power outlets, cable input sources, and connections for speakers and accessories.
• Avoid direct sunlight, heat and vibrations and do not place in direct ow of trac.
• SELECT A WEIGHT BEARING WALL. The wall must be able to safely support four times the combined load of the
equiptment and all attached hardware and components.
Mounting Height:
The optimal viewing height is to center the display at eye level when seated. Many people consider this to be too low
for a wall mount, and commonly use the following rule for placement:
Position the bottom of the display no higher than eye level when seated, and the top of the display no higher than
eye level when standing. Anything within these limits should normally provide a comfortable viewing experience.
Wall Suitability:
The hardware included is suitable for mounting to walls made of brick, solid concrete, concrete block or wood studs
covered with drywall. If your mounting situation is dierent, please consult a qualied installer or contact STC Customer
Care at [phone].
Wall Stability:
Carefully inspect the wall area you have selected. Examine the wall surface before you begin drilling.
• For concrete walls, check for damaged or loose concrete and do not drill in those areas.
• For brick or concrete block, never drill into the mortar between blocks.
• For wood studs, locate the wall studs and drill in the center of the stud.
• DO NOT DRILL NEAR ELECTRICAL WIRING AND WATER PIPES.
IMPORTANT: MAKE SURE THE WALL IS A WEIGHT BEARING WALL.
CAUTION: Failure to observe all safety precautions can result in serious physical injury and/or property
damage. Consult a professional installer or contact STC Customer Care at [email protected]
or [phone] if you have any questions.
!
BEFORE YOU BEGIN, MAKE SURE YOU CAREFULLY READ AND UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL.
This bracket system incorporates a slide mount design. Our goal is to make this installation easy for you. Please
follow the instructions in the order presented in this manual and be sure to observe all warnings and cautions.
!
7 of 12
www.stcny.com
wood stud masonry
Ø 5/32” (4 mm)
wood drill bit
stud nder Ø 1/4” (6 mm)
Ø 3/8” (10 mm)
masonry drill bits
nylon anchor
OR

solid wood stud
(2” x 4”)
Avoid drilling near electrical wiring and water pipes. Mount must be attached to a weight bearing wall
and must be installed directly onto center of wood stud. Failure to observe all safety precautions can
result in serious physical injury and/or property damage. Consult a professional installer or call STC
Customer Care at [phone] if you have any questions.
!
Use commercially available stud nder to locate stud centers.
Ø 5/32” (4 mm)
wood drill bit
3”
(76 mm)
Tighten lag bolts so wall plate is rmly attached.
DO NOT OVER TIGHTEN. Over tightening can
damage screws, greatly reducing holding power.
!
!CAUTION: Wear safety glasses
when operating power tools.
8 of 12
www.stcny.com
Use 5/32” (4 mm) wood drill bit to drill 3“ (76 mm) pilot holes.
a
.1.1.1
7attach wall plate
to wood stud
Use built in level. Position so bubble is centered.

brick, concrete block or
solid concrete (3000 psi)
Ø 1/4” (6 mm)
Ø 3/8” (10 mm)
masonry drill bit
!CAUTION: Wear safety glasses
when operating power tools.
3”
(76 mm)
Insert anchors. Use hammer until completely ush
to concrete surface, even if covered by a layer of
drywall or other material.
Tighten lag bolts so wall plate is rmly attached.
DO NOT OVER TIGHTEN. Over tightening can
damage screws, greatly reducing holding power.
!
Avoid drilling near electrical wiring and water pipes. Mount must be attached to a weight bearing wall.
Failure to observe all safety precautions can result in serious physical injury and/or property damage.
Consult a professional installer or call STC Customer Care at [phone] if you have any questions.
!
9 of 12
www.stcny.com
Use built in level. Position so bubble is centered.
Use 1/4” (6 mm) masonry drill bit to slowly drill 3“ (76 mm) pilot holes.
Then use 3/8” (10 mm) masonry drill bit to expand pilot holes.
!Do not drill into mortar between bricks or
concrete blocks or into loose concrete.
7attach wall plate
to masonry walls
b

9
8
10 of 12
www.stcny.com
mount
secure
NOTE: Plug in cables before mounting the display as
they may be dicult to reach afterwards.
Gently lower display on wall plate.
Use M4 x 8mm safety screw to secure.
!
Use two people to
lift larger displays.

11 of 12
www.stcny.com
10 adjust !
Use two people when
adjusting larger displays.
Hold display before loosening knob, and continue to hold until you have tightened
the knob again. Make sure teeth in VESA plate and mount line up before tightening.
!
Tighten knob rmly when you nish. DO NOT OVER TIGHTEN.
!
Loosen knob enough to seperate the VESA plate from the mount.
Rotate VESA plate and adjust tilt. Make sure teeth
in VESA plate and mount line up and
then tighten knob.
Mount pivots 180 degrees at each joint.
Tilt forward or backward
+/- 25 degrees.

STC warrants that it will replace or repair this item, at its sole
discretion, free of charge, should it prove defective in materials or
workmanship.
If a claim is made under this warranty, the mount should be
returned, freight prepaid, with the original purchase receipt to
your dealer or to a Space Saver distributor.
This warranty does not apply to:
• Normal wear and tear
•Friction damage
•Coating defects
•Defects caused by loosened screws, nuts or bolts
•Improperly mounting the bracket to the wall
•Improperly installing the bracket to the display
•Failure to properly follow installation instructions
•Modication or repairs not made or authorized by STC
•Loading beyond permitted load
•Intentional misuse
LIFETIME WARRANTY
Systems Trading Corporation
450 7th Avenue, Suite 2809, New York, NY 10123
Phone: [phone] Toll Free: [phone] Email: [email protected]
Copyright © 2008, Systems Trading Corporation, All rights reserved.
12 of 12
www.stcny.com