Steamfast SF-425 User manual

TRAVEL FABRIC STEAMER
OWNER’S GUIDE
SF-425

2 |ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
DANGER
Any appliance is electrically live even when switched off. To reduce risk of electrical shock:
1. Always unplug power cord immediately after using.
2. Do not place or store unit where it can fall or be pulled into a sink or tub.
3. Do not place in, or drop into water or other liquid.
4. If unit falls into water, immediately unplug power cord. Do not reach into the water.
WARNING
To reduce risk of burns, electrocution, re or injury to persons:
1. Do not tamper with or modify this product in any way. The manufacturer assumes
no responsibility for damage or injury caused by failure to follow these instructions,
improper use, or unauthorized product modication. Any such actions will invalidate the
productwarranty.
2. Use Travel Fabric Steamer only for its intended purpose as indicated in this manual.
3. If an extension cord is necessary, use a properly rated cord (15 ampere, 14 gauge). Use care
to position extension cord where it is least likely to be damaged or tripped over during use.
4. Before plugging power cord into electrical outlet, be sure that all electrical information on
rating label agrees with your power supply.
5. To reduce likelihood of circuit overload, DO NOT operate another high wattage appliance on
the same circuit as this unit.
6. To protect against risk of electrical shock, do not immerse unit in water or other liquids. Do
not use power cord as handle, let it hang over edges of counters, or be crimped or closed
indoors.
7. Never yank power cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
8. Do not operate unit with a damaged power cord or if the unit has been dropped or
damaged. To avoid risk of electrical shock, do not disassemble unit; contact Steamfast
Consumer Service for examination and repair. Incorrect reassembly can cause a risk of
electrical shock when unit is used.
9. Close supervision is required for any appliance being used near children, pets and plants. Do
not leave unit unattended while plugged in.
10. This unit is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
WARNING: To reduce risk of re, electrical shock or injury, the following
basic safety precautions should always be followed when using an
electricalappliance.
WARNING: To reduce the risk of electrical shock, this appliance uses a
grounded (three-pronged) plug. This plug will t in a grounded wall outlet
only one way. If the plug does not correctly t in the outlet, contact a
licensed electrician to install a proper outlet. DO NOT attempt to modify the
plug or defeat this safety feature.
READ ALL INSTRUCTIONS BEFORE USE

ENGLISH |3
Questions or comments?
•steamfast.com
• [email protected]
•1-800-711-6617
Speak your mind! We invite you to review this product online:
steamfast.com/reviews
given supervision or instruction concerning use of the unit by a person responsible for
theirsafety.
11. Do not use unit where aerosol-based products are being used or where oxygen is
beingadministered.
12. Always check that power cord is unplugged and unit is sufciently cool (allow at least 5
minutes of cooling time after use) before lling Boiler with water. Do not attempt to use unit
without properly lling Boiler.
13. When lling Boiler, only water should be used in unit – other cleaning agents could damage
unit or cause injury. Distilled or de-mineralized water is highly recommended, in order to
minimize potential build-up of mineral deposits. Do not overll unit.
14. To reduce risk of contact with hot water emitting from Steam Nozzle, check appliance
before each use by positioning it away from body and turning it on. Do not operate unit if
Steam Nozzle is blocked.
15. Burns can occur from touching hot plastic parts, hot water or steam. Do not touch Steam
Nozzle while unit is in use. Use caution when you turn unit upside-down – there may be hot
water in Boiler.
16. When steaming any material for the rst time, it is recommended that you consult the
manufacturer’s guidelines for the fabric being steamed. For items in question, test on an
inconspicuous area before proceeding.
17. Synthetic materials (such as 100% nylon or polyester) are sensitive to heat and may be
damaged by exposure to hot steam. Steam is recommended for use only on natural bers
such as cotton, linen or wool, as well as nylon or polyester blends.
18. Do not allow power cord to touch hot surfaces during use. Loosely bundle cord
whenstoring.
19. Always allow Travel Fabric Steamer to cool (15 minutes for complete cooling) and empty
Boiler before storing.
20. Only plug power cord directly into 120V outlet.
This equipment may generate, use and/or radiate radio frequency energy that may cause
harmful interference to radio communications. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to contact Steamfast Consumer Service at 1-800-711-6617.
Please refer to our website for the most current version of our owner’s guide.

4 |ENGLISH
Product Information
The following features are included with your Travel Fabric Steamer. Carefully inspect the
packing material for all parts listed below. To obtain possible missing parts, refer to Page 10 of
this manual for Consumer Service contact information.
UNIT FEATURES
Steam Nozzle
Water Reservoir Cap
Handle
Boiler Level Window
Boiler (Internal)
On/Off Switch
Silicone Ring
1
2
3
4
5
6
7
3
4
6
1
2
7
5

ENGLISH |5
•The Steam Nozzle (1) emits the ow of hot, penetrating steam produced by the Boiler.
•The Water Reservoir Cap (2) is designed to safely contain steam inside the Boiler, while
providing easy access to the Boiler’s ll hole.
•The Handle (3) is designed to stay cool while providing maximum grip and comfort.
•The Boiler Level Window (4) permits a clear view of the water level inside the Boiler, and is
marked to indicate the maximum water level for easy lling.
•The Boiler (5) is the internal reservoir where water is held and converted into steam. For
optimal steam production, the Boiler should not be lled past the MAX mark (4 oz. / 118 ml.)
indicated on the Boiler Level Window.
•The On/Off Switch (6) powers the unit On and Off.
• The Silicone Ring (7) provides a non-slip surface and stability.

6 |ENGLISH
FILLING BOILER WITH WATER
1. Place Travel Fabric Steamer on a at, level surface.
2. Make sure power cord is unplugged from electrical outlet.
CAUTION: If unit has been in use, allow Boiler to cool (5 minutes for minimum cooling
before removing Water Reservoir Cap and adding water).
3. Remove Water Reservoir Cap by turning clockwise.
4. Carefully ll Boiler with water from a faucet, bottle or cup. Use Boiler Level Window to
gauge water level, stopping when it reaches the MAX mark.
WARNING: MAX mark on Boiler Level Window represents the unit’s maximum usable
water capacity (4 oz. / 118 ml.). Exceeding this amount will result in water spitting from
Steam Nozzle.
NOTE: In order to minimize potential mineral build-up and prolong the life of your Travel
Fabric Steamer, distilled or de-mineralized water is recommended when llingBoiler.
5. Replace Water Reservoir Cap by turning counter clockwise and until the arrows are aligned.
Aligned Arrows
Using Your
Travel Fabric Steamer

ENGLISH |7
FABRIC STEAMING
CAUTION: When steaming any material for the rst time, it is recommended that you test
on a small inconspicuous area before proceeding. Do not use on synthetic fabrics such as
100% nylon or polyester, or other steam-sensitive materials.
NOTE: Be sure the Boiler has already been lled before following these steps (refer to
Page 6 for details).
1. Plug power cord into a standard electrical outlet.
2. After approximately 1 minutes, steam will begin emitting from Steam Nozzle.
3. Direct Steam Nozzle towards fabric material you wish to steam. See below for additional tips
and procedures.
CAUTION: Always be sure that Steam Nozzle is pointed in a safe direction (away from
yourself, other people, pets and plants) when steaming.
Steaming garments:
• Hang garment from a clean, rust-free hanger.
• Direct Steam Nozzle towards bottom of garment. Steam will rise along inside and outside
of material, removing wrinkles. Slowly slide Steam Nozzle upward from bottom to top
ofgarment.
• Direct Steam Nozzle away from garment and smooth material with your free hand.
• Repeat as necessary until garment is fresh and wrinkle-free.
General steaming tips:
• For most effective results, hold Steam Nozzle within 1/2” of fabrics, or press it directly
against surfaces.
• Curtains and draperies can be steamed while still hanging.
• To remove wrinkles from towels, handkerchiefs and napkins, drape them over a rod or
towel rack and gently steam them.
• Heavier fabrics may require repeated steaming to achieve desired results.
• To remove exceptionally stubborn wrinkles, steam both sides of fabric.
• Be especially careful when steaming any delicate fabrics that may be damaged by heat or
water spotting.
• To sanitize a fabric, hold Steam Nozzle within 1/2 inch of a single area for at least 5
seconds. Use caution when doing this on more delicate fabrics.
When you are nished using your Travel Fabric Steamer, immediately unplug power cord from
electrical outlet. Refer to Storage & Care guidelines on Page 8 of this manual for proper
storage and maintenance procedures.

8 |ENGLISH
PROPER STORAGE
Preparing your Travel Fabric Steamer for storage is quick and simple. When you have nished
your steaming tasks, follow the steps listed below.
1. Unplug power cord from electrical outlet.
2. Allow unit to cool (15 minutes for complete cooling).
3. Remove Water Reservoir Cap. Drain any water remaining in Boiler into a sink or tub, then
add 1 oz. water. Shake to release mineral buildup and empty tank to minimize potential
mineral build-up. Replace Water Reservoir Cap.
4. Bundle power cord loosely.
5. Store Travel Fabric Steamer in a cool, dry location.
MINERAL BUILD-UP
A common maintenance need for steam appliances is the removal of build-up caused by high
mineral content in many municipal water supplies. This mineral build-up may cause the unit to
spew water, limit the effectiveness and reduce the life of your Travel Fabric Steamer.
The best way to minimize mineral build-up is to use distilled or de-mineralized water when
using your Travel Fabric Steamer. In addition, it is recommended that the Boiler be cleaned
at least once a month in order to remove any deposits that form. This will help to extend the
life of your Travel Fabric Steamer and keep it functioning at its maximumpotential.
Maintenance:
After EACH USE, allow unit to cool, add 1 oz. water, shake to release mineral buildup and
empty tank.
To remove mineral build-up:
1. Unplug power cord from electrical outlet.
IMPORTANT: Unit should remain unplugged during cleaning procedure.
2. Allow unit to cool (15 minutes for complete cooling).
3. Remove Water Reservoir Cap and drain any water remaining in Boiler into a sink or tub.
4. Using a measuring cup, measure 2 oz. (59 ml.) of vinegar.
5. Slowly pour vinegar into Boiler.
6. Allow vinegar to soak in Boiler for 30-40 minutes.
7. Drain vinegar from Boiler into a sink or tub. Rell Boiler with fresh water, drain and repeat
until vinegar odor dissipates.
8. Replace Water Reservoir Cap.
9. Bundle power cord loosely and store Travel Fabric Steamer in a cool, dry location.
Storage & Care

ENGLISH |9
Troubleshooting
PROBLEM POSSIBLE CAUSE SOLUTION
Unit fails to heat up. Unit is not plugged in. Plug power cord into electrical outlet.
Household circuit breaker / ground
fault interrupter has tripped or
blown a fuse.
Reset circuit breaker / ground fault inter-
rupter, or replace fuse. For
assistance, contact a licensed electrician.
Unit is damaged or in need
ofrepair.
Immediately cease usage and unplug. Con-
tact Consumer Service for
assistance (see Page 10 for details).
No water in Boiler. Refer to Filling Boiler With Water proce-
dure on Page 6 to rell Boiler.
Steam output is weak or intermit-
tent.
Water level in Boiler is running low. Refer to Filling Boiler With Water proce-
dure on Page 6 to rell Boiler.
Mineral build-up in unit. Refer to Mineral Build-up section on Page 8
for cleaning procedure.
Unit is spewing water. Water tank is overlled. Do not ll past max line.
Mineral build-up in tank. Refer to Mineral Build-up section on Page 8
for cleaning procedure.

10 |ENGLISH
PRODUCT SPECIFICATIONS
SF-425
120V
800W
6.7A
4 OZ. (118 ML.)
1 MIN. (APPROXIMATE)
6.5 MIN. (APPROXIMATE)
1.19 LBS. (0.54 KG.)
5.75” (14.6 CM.) x 3.57” (9.1 CM.) x 8.27” (21.0 CM.)
8’ (244.0 CM.)
MODEL
VOLTAGE
WATTAGE
AMPERAGE
WATER CAPACITY
HEATING TIME
CONTINUOUS STEAM TIME
UNIT WEIGHT
UNIT DIMENSIONS
POWER CORD LENGTH
NOTE: Due to continuing improvements, part numbers listed above may change.
For assistance ordering parts, please contact Consumer Service directly.
Product Support
CONSUMER SERVICES
For problems with your Travel Fabric Steamer, please refer to the troubleshooting guide
located above. Additional inquiries should be directed to our consumer support services
through our Web site, steamfast.com.
If you do not have internet access, you may also contact our Consumer Service Department by
telephone, at 1-800-711-6617.
NOTE: In order for our Consumer Service representatives to help you as quickly and
efciently as possible, please have the following information ready before calling:
• Purchase information (where and when you purchased this product)
• Copy of purchase receipt / proof of purchase
• Product serial number (located near electrical specication label on bottom of unit)
• Date code (4-digit number located on electrical specication label on bottom of unit)
For information regarding your 1 Year Limited Warranty, refer to Page 11 of this manual.

ENGLISH |11
2-YEAR LIMITED WARRANTY
What is covered
Steamfast, a division of Vornado Air, LLC (“Steamfast”). Subject to the terms and conditions of
this 2-Year Limited Warranty (“Warranty”) as set forth below, Steamfast warrants to the original
consumer or purchaser (“Buyer”) that this Steamfast®-branded steam product, excluding
all accessories and attachments, (the “Product”) is to be free from defects in material and
workmanship for a period of two (2) years from the date of purchase when used and maintained
in accordance with the Owner’s Guide (the “Warranty Period”). In the event Buyer noties
Steamfast of a defect in the Product within the Warranty Period, Steamfast will replace the
Product and/or defective component parts, as applicable and necessary. Any such replacement
will be made at no charge to Buyer for parts or labor, provided that Buyer shall be responsible
for all shipping and transportation costs associated with returning the Product to Steamfast for
inspection and covered replacement.
What is not covered
This Warranty shall not be applicable to damage or loss caused in whole or in part by:
• Repairs, modications or alterations to the Product by anyone other than Steamfast.
• Use or operation of the Product outside the permitted or intended uses described by
Steamfast in the Owner’s Guide, or other careless operation, handling, misuse, or abuse of
theProduct.
• Lack of proper maintenance or timely cleaning of the Product as specied in the
Owner’sGuide.
• Use of the Product other than for normal household purposes.
• Normal wear and tear.
• Used consumable parts, accessories and attachments, including, but not limited to, brushes,
hangers, scrub pads and mop pads.
• Use of parts and accessories other than those produced or recommended by Steamfast.
• Cosmetic damage, such as scratches, nicks and dents.
• Damage caused by accident, water, ood, re or other acts of nature or external causes.
Warranty limitations and exclusions
• NO OTHER EXPRESS WARRANTY IS GIVEN BY STEAMFAST TO BUYER AND NO
REPRESENTATIVE HAS THE AUTHORITY TO MAKE REPRESENTATIONS OTHER THAN THOSE
PROVIDED HEREIN.
• THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF AND ALL IMPLIED WARRANTIES, SPECIFICALLY THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
LIMITED TO THE DURATION OF THE WARRANTY PERIOD, UNLESS A SHORTER PERIOD IS
PERMITTED BY LAW.
• STEAMFAST’S REPLACEMENT OF THE PRODUCT IS THE EXCLUSIVE REMEDY. UNDER NO
CIRCUMSTANCES SHALL STEAMFAST BE LIABLE TO BUYER OR ANY OTHER PERSON FOR
ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR OTHER DAMAGES, EVEN IF STEAMFAST
HAS BEEN ADVISED OF OR COULD REASONABLY FORESEE THE POSSIBILITY OF SUCH
DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR DAMAGE, WHETHER
RISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT OR UNDER ANY OTHER
THEORY OF LAW.
Warranty Information

12 |ENGLISH
• THIS WARRANTY GIVES BUYER SPECIFIC LEGAL RIGHTS. BUYER MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE-TO-STATE. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, AND SOME
STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO BUYER.
How do you register the Warranty
Buyer must complete an application to register this Warranty within sixty (60) days following date
of purchase. Buyer may either visit Steamfast’s website at steamfast.com and complete an online
application or mail a completed application to Steamfast. Failure to register this Warranty within
sixty (60) days following date of purchase will render this Warranty null and void.
Warranty service
For warranty service, call 1-800-711-6617 or email [email protected] to obtain a
Return Authorization (“RA”) form. Include the Product model number and serial number, as well
as Buyer’s name, address, city, state, zip code and phone number when contacting Steamfast
for warranty service. Buyer may be required to provide the original sales receipt for purposes of
verifying date of purchase. After receiving the RA form, the Product must be shipped, postage
prepaid by Buyer, to:
Steamfast
Attn: Warranty & Repair
415 E. 13th Street
Andover, KS 67002, U.S.
To assure proper handling, packages must be clearly marked with the RA number. Packages not
clearly marked with the RA number may be refused at the receiving dock.
Important: After receiving return authorization, carefully pack the Product to avoid damage in
shipping. Damage in shipping is not covered by the Warranty and shall be the sole responsibility
of Buyer. Damage or loss not covered by this Warranty or occurring outside the Warranty Period
will require a fee to cover the cost of handling and shipping. All such fees and costs shall be the
sole responsibility of Buyer.
Please allow at least 1-2 weeks for return of the Product after it is received by Steamfast. For ease
of recordkeeping, it is recommended that Buyer staple or attached the original sales receipt to
this Owner’s Guide and record the Product serial number (located on the Product specications
decal) here:
________________________________________________
© 2018 Vornado Air, LLC • Andover, KS 67002, U.S.
Specications subject to change without notice.
Steamfast® is a trademark owned by Vornado Air, LLC.
Manufactured in China.
Steamfast Consumer Service
W: steamfast.com • P: 1-800-711-6617 • E: [email protected]
Warranty Information

Steamfast
415 East 13th, Andover, KS 67002
1-800-711-6617 steamfast.com [email protected]
T425-005 R-, V02