Suisei MS4559-52H User manual

（1/5）
MS4559-52H REV.A
MADE IN JAPAN
IC1
8J11
(52P6A-A)
(PLQP052JA-A)
t
cable connection connector(J1)
IC socket：52LQFP type
MS4559-52H Users Guide
Suisei Electronics System Co., Ltd
4th Edition issued June 2011
1. General Description
MS4559-52H is a writing target board for standard serial I/O mode used by connecting to EFP-I/1M or
EFP-S2/S2V.
Reading and writing data to microcomputer 4559, 455A groups with built-in Renesas Electronics 4 bit
QzROM, is enabled by using MS4559-52H.
IC socket for 52-pin 0.65mm pitch LQFP (PRQP052JA-A) (52P6A-A) is mounted on MS4559-52H.
＜Packing contents＞
１）MS4559-52H
２）Users guide (this manual）
External Figure of MS4559-52H is shown in Fig 1.1.
Fig 1.1 MS4559-52H External Figure

（2/5）
EF1TGCB-A
E
FP-S2/S2V(EF1SRP-01US2)
E
FP-I/1M(EF1SRP-05U)
MS4559-52H
E
FP-S2/S2V + EF1CNT-96P(EF1SRP-05U)
(3-wire target connection cable)
Target cable connection connector(J1)
2. Device constitution and a connection method
2.1 Device constitution
Device constitution when you use MS4559-52H is shown in Fig.2.1.
Fig2.1 Device constitution
Main body Unit Cable
EFP-I/1M EF1SRP-05U
EF1TGCB-A(3-wire target connection cable)
(separate sale)
EFP-S2/S2V
EF1SRP-05U ＋EF1CNT-96P
*1
EF1SRP-01US2
*1) when you use EF1SRP-05U in EFP-S2/S2V, EF1CNT-96P (separate sale) is necessary.
2.2 Connection Process
In case MS4559-52H is connected, please use EF1TGCB-A (3-wire target connection cable) as shown in
Fig.2.1.
Fig.2.1 Connection with EF1TGCB-A (3-Wire Target Connection Cable)

（3/5）
Above corresponding versions might change without notice on account of the future
capability improvement, etc. Furthermore in case the upgrade procedure manual is
attached when this product is purchased, please refer to that manual as a priority.
3. List of Corresponding MCU and corresponding version
3.1 Corresponding MCU
A corresponding MCU list of MS4559-52H is shown in Fig.3.1.
Fig3.1 List of Corresponding MCU
Main body Device type Corresponding
MCU name
Program memory
area
EF1SRP-05U SW
setting
EFP-I/1M
M34559G6
(Vdd:4.5V Vpp:7.9V) M34559G6FP 0h～17FFh
T_VPP：7.9V side*1
M3455AG8
(Vdd:4.5V Vpp:7.9V) M3455AG8FP 0h～1FFFh
M3455AGC
(Vdd:4.5V Vpp:7.9V) M3455AGCFP 0h～2FFFh
EFP-S2/S2V
M34559G6(VDD:4～
4.7V) M34559G6FP 0h～17FFh
T_VPP：7.9V side *1
M3455AG8(VDD:4～
4.7V) M3455AG8FP 0h～1FFFh
M3455AGC(VDD:4～
4.7V) M3455AGCFP 0h～2FFFh
*1) when you use EF1SRP-05U in EFP-S2/S2V, EF1CNT-96P (separate sale) is necessary.
3.2 About Software version(S/W)
Please download the latest version up data on the following site when the S/W version.
Please use S/W of the latest version and confirm S/W version regularly.
【S/W version confirmation method】
The version numbers are displayed by [Help]→[About] in the WinEFP or WinEFP2 window menu.
< EFP-I/IM S/W the latest free download site >
http://www.suisei.co.jp/download_e/productdata_efp1_e.html
< EFP-S2 S/W the latest free download site >
http://www.suisei.co.jp/download_e/productdata_s2_e.html
< EFP-S2V S/W the latest free download site >
http://www.suisei.co.jp/download_e/productdata_s2_e.html
Note on Corres
p
ondin
g
Versions

（4/5）
IC1
8J11
MS4559-52H REV.A
MADE IN JAPAN
MCU
No.1 Pin
4. Insertion Direction of MCU and cleaning of IC socket
4.1 Insertion Direction of MCU
When MCU is inserted, No.1 pin of the IC socket on MS4559-52H and MCU’s No.1 pin should be connected.
The wrong insertion would cause a serious breakage of MCU.
Insertion direction of MCU is shown in Fig.4.1.
Fig.4.1 Insertion Direction of MCU
4.2 Cleaning of IC Socket
A contact pin inside of the IC socket of the MCU unit might deteriorate and a contact failure might occur
because of the number of times used and its age of service. As the contact failure may cause incorrect
writing of MCU and malfunction of the writer, please take the below measures.
Though enquiries on contact failures can be made, we regard IC sockets as consumable supplies. We may
recommend you to replace them if a contact failure of IC socket occurs due to its use deterioration.
【Recommended item for cleaning】
About the cleaning of the contact pin in the IC socket, we recommend the use of the nanotech brush (Kita
Mfg Co.,Ltd).
The nanotech brush can remove the dirt which stuck to a contact pin, a very small amount of metastasis of
solder. When a contact poor problem occurred, please try it.
About nanotech brush, please ask us or Kita Mfg.Co.Ltd (refer to the following site).
Nanotech brush (Kita Mfg Co., Ltd.) http://www.kita-mfg.com/pro_nanotech_e.html
(i) Please clean the contact pin surface inside of IC socket with a brush, etc. regularly, depending
on the number of times used.
(ii) If the product is not to be used for a long period, please keep it with less humidity in a
plastic bag, etc.
Measures against IC Socket Contact Failure

（5/5）
5. List of Pin Connection
Connector terminal names target cable connection connector of MS4559-52H is shown in List 5.1.
List 5.1 Terminal List of target connection connector (J1)
Pin No. Terminal Name I/O(writer
side)
Pin No. Terminal Name I/O(writer
side)
１ＢＵＳＹ Input ５ＳＤＡ I/O
２ＶＰＰ Output ６ＰＧＭ／ＯＥ Output
３ＶＤＤ Output ７ＲＥＳＥＴ Output
４ＳＣＬＫ Output ８ＧＮＤ －