SweetPRO FR-12MC4 User manual

English
SweetPRO FR-12MC4
IP65 LED Outdoor Fluterr mpe
Best.Nr.
SWPFR12MC4IP
User m nu l

SweetPRO FR-12MC4 IP65 LED Outdoor Fluterr mpe|Best.Nr. SWPFR12MC4IP
Page 2
With its compact dimensions and modern elegant design, SweetPRO FR-12MC4 IP 5 LED Outdoor is ideal for theatrical, live shows and
architectural applications.
The new high power RGBW full color LED technology allows the creation of a wide range of colours, reduces considerably the
consumption and removes maintenance and lamp changing (the medium life of the LED is of 100.000 hours, 10 years in constant use).
IMPORTANT!
READ CAREFULLY THE INSTRUCTION LEAFLET IN ALL ITS PARAGRAPHS. THE KNOWLEDGE OF THE INFORMATION AND OF THE
LIMITATION HELD IN IT, IS BASIC AND FOUNDAMENTAL FOR A CORRECT AND SAFE USAGE OF THIS PRODUCT.
IMPORTANT!
BEFORE ANY (MAINTENANCE, CLEANING ETC.) ACTION, SWITCH OFF THE POWER SUPPLY.
IMPORTANT!
-This device is suitable for indoor and outdoor use (room temperature cannot be higher than 25°C)
-This device is suitable for direct assembling on normally flammable surfaces.
Technic l specific tions Dimensions
• Body made of die-cast aluminium + steel sheets
• Black epoxy powder coating
• Power supply:100/240V 50/ 0Hz
• Current: 0, A (230v)
• Power: 120 W
• Max power supply: 130VA
• Source: 12 x10 W full color LED
• Average LED life: 100.000 h
• Colour changing: RGBW e HSV system
• Functioning: DMX Signal and automatic mode
• Channels: : 4/5/7/8/13, 8/1 BIT DMX 512
• Weight: 4,1 Kg
Inst ll tion
The projector can be fixed in any position. For floor installation, lean the projector using the two feet. For suspending use, it is needed
to install an appropriate clamp. It must be located in a well ventilated position. Make sure the structure You are fixing the product to
can stand the product load.
Accessories
•“c” Clamp
EN

SweetPRO FR-12MC4 IP65 LED Outdoor Fluterr mpe|Best.Nr. SWPFR12MC4IP
Page 3
Connections
The projector is fitted with a power supply cable for power IN, a power supply cable for power OUT with IP 5 connectors and two
XLR 5 Poles IP 5 connectors for DMX IN and OUT signal (Fig.1)
Any modification to this luminaries, without authorization, is forbidden.
This lantern must be powered according to the voltage and frequency showed on its label (100/240V 50/ 0Hz). Connect the power
cable to the socket. We suggest to connect each projector to its own switch so that they can be individually switched on with a remote
control.
To remote control the projectors is required the use of a DMX512 control desk.
For the connection of signal use cable EIA rs-485 type: two core screened, 120Ω characteristic impedance, 22-24 AWG, low capacity, 1
XLR 5 poles MALE connector and 1 XLR 5 poles FEMALE connector.
To form a DMX chain, connect the DMX control desk to the first projector’s DMX IN, then from its DMX OUT to the DMX IN of the
second projector and so on.
For a correct functioning of the DMX signal, it is necessary to put a terminal into the DMX OUT of the last projector. This terminal is
made of 1 XLR MALE connector with a 120Ω resistance welded between PIN 2 and PIN 3.
Digit l displ y nd functioning options
Using the digital display, it is possible to change the functioning options, drive the projector in automatic mode with presets or
programs and with Master/Slave functions, display projector information and reset settings to default.
After 30 seconds without working, the display will turn off.
The low right dot is a dmx signal indicator:
-Fixed ON : dmx signal is linked
-Slow flashing: dmx signal is not linked
-Quik flashing: dmx signal is linked but control channels are not enough
Addressing of the projector
To control many SweetPRO FR-12MC4 IP 5 LED Outdoor individually, it is necessary to assign to each one a different DMX address ,
setting the starting channel taking into consideration that one Projector books 8 channels (4 or 5 or 7 or 8 or 13 channels depending on
the functioning mode set).
For example, if we have projectors, it will be necessary to set them on the channels 1, 9, 17, 25, 33, 41…
To set the DMX channel use buttons ‘UP’ or ‘DOWN’ until you can see ‘Address’ on the display , then press ‘ENTER’. Change the DMX
address using the ‘UP’ ‘DOWN’ keys and then press ‘ENTER’ to confirm.
EN
DMX connector:
1: GND (screen)
2: data –
3: data +
4: NC
5: NC
Fig. 1
DMX OUT DMX IN
Power supply
connection:
Power supply: 100/240V
50/ 0Hz
1 – Line
2 – Neutral
3 – N.C.
4 - Earth
1
2
3
4

SweetPRO FR-12MC4 IP65 LED Outdoor Fluterr mpe|Best.Nr. SWPFR12MC4IP
Page 4
Description of the m in menu
To scroll the items of this menu use ‘UP’ and ‘DOWN’ keys.
Visu lizz tion Option Description
Addr DMX addressing Press ‘ENTER’ to display the current DMX address. Use ‘UP and ‘DOWN’
keys to change value and press ‘ENTER’ to confirm or ‘ESC’ to cancel.
Mode Setting of DMX mode
Press ‘ENTER’, the display will show the current DMX mode. Using ‘UP and
‘DOWN’ keys, change the DMX mode and then press ‘ENTER’ to confirm.
To see all possible settings, see the ‘DMX description’.
StdA Stand alone functioning
Press ‘ENTER’ to set the projector in stand alone mode. Press ‘UP’ and
‘DOWN’ to select the fixed colour (c) or the program (p) to play. N.B.
There is no DMX output. Press ‘ESC’ to stop this function.
Dmxo Automatic functioning with DMX
out
Press ‘ENTER’ to set the projector in stand alone mode. Press ‘UP’ and
‘DOWN’ to select the fixed colour (c) or the program (p) to play. N.B.
There is DMX output to control other projectors on dmx line. Press ‘ESC’ to
stop this function.
Hi-p Boost of LED power Press ‘ENTER’ to display the current state of ‘Hi-p’ function. If it is ‘off’, the
supply of LEDS is 700 mA, if it is ‘on’ supply of LEDS is 820 mA
Smoo Dimming mode
Press ‘ENTER’ to display the current dimming mode. Change the value
using the ‘UP or ‘DOWN’ keys then press ‘ENTER’ to confirm. If the value
is ‘off’, the dimming will be quick and nervous. If the value is ‘on’, the
dimming will be smooth.
F n Fan settings On this model there is no effect.
Temp Projector temperature Press ‘ENTER’ to display the current projector temperature. Press ‘ESC’ to
exit.
M xt Maximum projector temperature Press ‘ENTER’ to display the maximum projector temperature from the last
time it was turned on. Press ‘ESC’ to exit.
Unit Unit of measurement
Press ‘ ENTER’ to display the current unit of measurement for the
temperature. The values can be ‘cels’ (Celsius) or ‘fahr’ (Fahrenheit). Press
‘UP’ or ‘DOWN’ to change the value and press ‘ENTER’ to confirm or ‘ESC’
to exit.
C lr Red calibration Press ‘ENTER’, set the maximum level for Red using ‘UP’ and ‘DOWN’ .
Press ‘ENTER’ to confirm and ‘ESC’ to exit.
C lg Green calibration Press ‘ENTER’, set the maximum level for Green using ‘UP’ and ‘DOWN’ .
Press ‘ENTER’ to confirm and ‘ESC’ to exit.
C lb Blue calibration Press ‘ENTER’, set the maximum level for Blue using ‘UP’ and ‘DOWN’ .
Press ‘ENTER’ to confirm and ‘ESC’ to exit.
C lu White calibration Press ‘ENTER’, set the maximum level for White using ‘UP’ and ‘DOWN’ .
Press ‘ENTER’ to confirm and ‘ESC’ to exit.
Def Set all the values to default Press ‘ENTER’, select ‘reset’ using ‘UP and ‘DOWN’ to reset to default all
values. Press ‘ENTER’ to confirm and ‘ESC’ to exit.
Vers Software version Press ‘ENTER’ to display the firmware version of the projector. Press ‘ESC’
to exit.
Sern Serial number Press ‘ENTER’ to display the serial number of the projector. Press ‘ESC’ to
exit.
PASS
EN

SweetPRO FR-12MC4 IP65 LED Outdoor Fluterr mpe|Best.Nr. SWPFR12MC4IP
Page 5
Description of the DMX ch nnels:
mode=RGB7
mode=RGB8
mode=RGB4
mode =HSV
mode= HSV-
mode= CMY5
mode=RGB11 (16 bit)
Built-in Preset nd Progr ms
Preset Colour
Preset 1 Red
Preset 2 Orange
Preset 3 Yellow
Preset 4 Light Yellow
Preset 5 Green
Preset 6 Aqua green
Preset 7 Cyan
Preset 8 Azure
Preset 9 Blue
Preset 10 Violet
Preset 11 Magenta
Preset 12 Fucsia
Preset 13 White
CH 1 CH 2 CH 3 CH 4 CH 5 CH CH 7
Red Dimmer
0-100%
Green Dimmer
0-100%
Blue Dimmer
0-100%
White Dimmer
0-100%
Strobe effect at
adjustable speed
Rainbow effect at
adjustable speed
Master Dimmer
0-100%
CH 1 CH 2 CH 3 CH 4 CH 5 CH CH 7 CH 8
Red Dimmer
0-100%
Green Dimmer
0-100%
Blue Dimmer
0-100%
White Dimmer
0-100%
Strobe effect at
adjustable speed
Rainbow
effect at
adjustable
speed
Master
Dimmer
0-100%
White with
color
temperature
regulation
CH 1 CH 2 CH 3 CH 4
Red Dimmer
0-100%
Green Dimmer
0-100%
Blue Dimmer
0-100%
White Dimmer
0-100%
CH 1 CH 2 CH 3 CH 4
Hue Saturation Intensity
Master Dimmer
Strobe effect at
adjustable speed
CH 1 CH 2 CH 3 CH 4
Hue
+white from 251 to 255
Saturation Intensity
Master Dimmer
Strobe effect at
adjustable speed
CH 1 CH 2 CH 3 CH 4 CH 5
Cyan Dimmer
0-100%
Magenta Dimmer
0-100%
Yellow Dimmer
0-100%
Black Dimmer
0-100%
Strobe effect at
adjustable speed
CH 1 CH 2 CH 3 CH 4 CH 5 CH CH 7 CH8 CH 9 CH 10 CH 11 CH 12 CH 13
Red m
Dimmer
0-
100%
Red l
Dimmer
0-
100%
Green
m
Dimmer
0-
100%
Green l
Dimmer
0-
100%
Blue m
Dimmer
0-
100%
Blue l
Dimmer
0-
100%
White
m
Dimmer
0-
100%
White l
Dimmer
0-
100%
Strobe
effect at
adjustable
speed
Rainbow
effect at
adjustable
speed
Master
Dimmer m
0-100%
Master
Dimmer l
0-100%
White with
color
temperature
regulation
EN

SweetPRO FR-12MC4 IP65 LED Outdoor Fluterr mpe|Best.Nr. SWPFR12MC4IP
Page 6
Progr m Colours Progr mmed times
Progr m 1 Red, Magenta, Blue, Cyan, Green, Yellow Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 2 Green, Azure, Violet Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 3 Red, Yellow, Blue Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 4 Blue, Green, Cyan Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 5 Orange, Blue, Green Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 6 Magenta, Yellow, Cyan Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 7 Red, Green, Blue Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 8 Blue, Cyan, Orange Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 9 Green, Yellow, Red Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 10 Red, Magenta, Blue, Cyan, Green, Yellow + Strobe Pause time: 8 seconds / Fade time: 0,5 seconds
Progr m 11 Red, Magenta, Blue, Cyan, Green, Yellow Pause time: 8 seconds / Fade time: 7 seconds
Progr m 12 Green, Azure, Violet Pause time: 8 seconds / Fade time: 7 seconds
Progr m 13 Red, Yellow, Blue Pause time: 8 seconds / Fade time: 7 seconds
Progr m 14 Blue, Green, Cyan Pause time: 8 seconds / Fade time: 7 seconds
Progr m 15 Orange, Blue, Green Pause time: 8 seconds / Fade time: 7 seconds
Progr m 16 Magenta, Yellow, Cyan Pause time: 8 seconds / Fade time: 7 seconds
Progr m 17 Red, Green, Blue Pause time: 8 seconds / Fade time: 7 seconds
Progr m 18 Blue, Cyan, Orange Pause time: 8 seconds / Fade time: 7 seconds
Progr m 19 Green, Yellow, Red Pause time: 8 seconds / Fade time: 7 seconds
Progr m 20 Red, Magenta, Blue, Cyan, Green, Yellow + Strobe Pause time: 8 seconds / Fade time: 7 seconds
Progr m 21 Red, Magenta, Blue, Cyan, Green, Yellow Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 22 Green, Azure, Violet Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 23 Red, Yellow, Blue Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 24 Blue, Green, Cyan Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 25 Orange, Blue, Green Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 26 Magenta, Yellow, Cyan Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 27 Red, Green, Blue Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 28 Blue, Cyan, Orange Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 29 Green, Yellow, Red Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 30 Red, Magenta, Blue, Cyan, Green, Yellow + Strobe Pause time: 24 seconds / Fade time: 0,5 seconds
Progr m 31 Red, Magenta, Blue, Cyan, Green, Yellow Pause time: 24 seconds / Fade time: 23 seconds
Progr m 32 Green, Azure, Violet Pause time: 24 seconds / Fade time: 23 seconds
Progr m 33 Red, Yellow, Blue Pause time: 24 seconds / Fade time: 23 seconds
Progr m 34 Blue, Green, Cyan Pause time: 24 seconds / Fade time: 23 seconds
Progr m 35 Orange, Blue, Green Pause time: 24 seconds / Fade time: 23 seconds
Progr m 36 Magenta, Yellow, Cyan Pause time: 24 seconds / Fade time: 23 seconds
Progr m 37 Red, Green, Blue Pause time: 24 seconds / Fade time: 23 seconds
Progr m 38 Blue, Cyan, Orange Pause time: 24 seconds / Fade time: 23 seconds
Progr m 39 Green, Yellow, Red Pause time: 24 seconds / Fade time: 23 seconds
Progr m 40 Red, Magenta, Blue, Cyan, Green, Yellow + Strobe Pause time: 24 seconds / Fade time: 23 seconds
EN

SweetPRO FR-12MC4 IP65 LED Outdoor Fluterr mpe|Best.Nr. SWPFR12MC4IP
Page 7
Huss Licht & Ton GmbH & Co. KG | www.huss-licht-ton.de | [e-mail]