Target 2812 Manual

DRILL STAND 2812
Operating and Maintenance Instructions
Spare Parts List

Some dust created by power sanding, sawing, grinding, drilling and other
construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
·Lead from lead-based paints,
·Crystalline silica from bricks and cement and other masonry
products and
·Arsenic and chromium from chemically-treated lumber.
Your risk from these exposure varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area
and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
·REFER TO MANUAL·
1

Introduction
Congratulations on your selection of a Target 2812 Drill Stand. We are certain you will be
pleased with your purchase of one of the finest drill stands on the market.
We want to help you get the best performance from your new machine and to operate it
safely. This manual contains the information on how to do that. Please read this manual
thoroughly, as it contains important information on operational safety, maintenance and
suggestions on how to get the best performance from your Target 2812 Drill Stand.
Best Wishes
Target
2

A Few Words About Safety
The safe operation of mechanical equipment is a partnership between the manufacturer
and the person who operates it. At Target we take this partnership very serious by designing our
equipment to be the safest and the most reliable equipment available to do the job. To insure
that both the performance and safety features of the equipment do the job, we work closely
with our partners to develop and implement strong maintenance and operator training pro-
grams. From design, to manufacture, to operation, to maintenance, it truly is the partnership
that keeps the equipment running smoothly, efficiently and most importantly, safely. Our equip-
ment comes with a comprehensive manual that covers operation, maintenance, parts and safety
instruction specific to the tool. Always read and fully understand all of the safety instructions
given in the manual before operating the equipment.
Safety messages - A safety message informs you about potential hazards that could hurt
you or others. Each safety message is preceded by one of the following three words: Danger,
Warning or Caution.
You WILL be KILLED or SERIOUSLY INJURED if you don’t follow instructions.
You CAN be KILLED or SERIOUSLY INJURED if you don’t follow instructions.
You CAN be INJURED if you don’t follow instructions.
Additional information as to the nature of the hazard is provided by the following hazards
symbols which appear throughout the manual in conjunction with safety message alert symbols.
3

LOCK CARRIAGE TO COLUMN WHEN NOT IN USE BY TIGHTENING LOCK SCREW (26),
PAGE 15.
MODEL 2812 ACCESSORIES ASSEMBLY INSTRUCTION
Assemble the Model 2812 Drill Stand as shown on page 14.
1. Attach Wheel Assembly (17) to Base (9 or 12), page 14, with capscrews and washers
(14 and 15).
2. Thread Jack Screw (1) into top of Column.
VACUUM SYSTEM, SINGLE PAD CONFIGURATION
1. Screw Stud (7) all the way into the Vacuum Pad.
2. Place frame on the base with the stud protruding through the frame.
3. Thread Nut (1) on the Stud and tighten it securely.
4. Close Single-Pad Valve (11) and connect Hose Assembly (10) to the pad.
OPERATION
1. Set pad with gasket on floor and tighten Nut (1), page 16 to remove all slack.
2. Close Release Valve (15), page 17 and make sure Single Pad Valve (11) is open.
3. Connect vacuum pump motor to 115 VAC power source and turn switch on.
4. Read vacuum on gauge (1), page 17; the valve should be approximately 25 in. hg.
DO NOT ATTEMPT TO DRILL IF THE VACUUM DOES NOT REACH 20 INCHES HG ON THE
GAUGE. DO NOT APPLY SO MUCH DRILLING PRESSURE THAT IT CAUSES THE RUBBER
GASKETS ON THE PADS TO PULL AWAY FROM THE FLOOR.
MAINTENANCE
1. Ensure that electrical components are safe before each use (see pages 5, 6, 7 & 8).
2. Check all vacuum distribution fittings to make sure they are tight.
3. Replace worn pad gaskets; use 3M weatherstrip adhesive or equivalent.
4. Maintain vacuum pump in accordance with the Gast Parts List and Operating and
Maintenance Instructions attached to pump.
4

VACUUM SYSTEM TROUBLESHOOTING
If the pump motor is running and the gauge indicates zero vacuum or low vacuum, check the
following:
1. Release Valve (15), page 17, not closed.
2. Vacuum pad gasket damaged or pads not seating on floor surface properly.
3. Pump filter clogged.
4. Pump filter jar not tight against gasket or jar cracked.
5. Vacuum distribution fittings not tight.
SAFETY INSTRUCTIONS FOR ALL ELECTRIC POWERED DRILLS
WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY
INCLUDING THE FOLLOWING ITEMS. READ ALL INSTRUCTIONS AND SAVE THEM
FOR FUTURE REFERENCE.
1. GROUND ALL TOOLS If the tool is equipped with a three prong plug, it should be
plugged into a three hole electrical receptacle. If an adapter is used to accommodate a
two hole receptacle, the grounding ear must be attached to a known ground. Never
remove the third prong.
2. DON’T FORCE DRILL It will do the job better and safer at the rate for which it was
designed.
3. WEAR PROPER APPAREL No loose clothing or jewelry to get caught in moving parts.
Rubber gloves and insulated non-skid footwear are recommended when working out
doors. Wear protective covering to contain long hair.
4. USE SAFETY GLASSES at all times.
5. DON’T ABUSE CORD Never carry the tool by its cord or yank it to disconnect from the
receptacle. Keep cord from heat, oil and sharp edges.
6. DISCONNECT TOOLS When not in use; before servicing, when changing accessories such
as bits, extension, etc.
7. GUARD AGAINST ELECTRIC SHOCK Prevent body contact with grounded surfaces such
as pipes, radiators, ranges and refrigerator enclosure
8. REMOVE WRENCHES. Form a habit of checking to see that wrenches are removed from
drill spindle and bit before turning it on.
5

9. MAINTAIN DRILL WITH CARE. Keep drill clean at all times for best and safest perform
ance. Follow instructions for lubricating. Keep handles dry, clean and free of oil or
grease. Inspect switches, tool cords and extension cords periodically and have them
repaired if damaged. Check moving parts for alignment and binding as well as for
breakage and improper mounting. Damaged parts should be repaired or replaced.
10. AVOID ACCIDENTAL STARTING. Don’t carry a plugged-in drill with your finger on the
switch. Be sure the switch is turned off before plugging in a drill. Do not use a drill if
the switch does not turn it on or off.
11. WEAR EAR PROTECTORS when using for extended periods.
12. ACCESSORIES. The use of any accessories other than what is listed or recommended for
this particular drill may be hazardous.
13. KEEP HANDS AWAY FROM CUTTING EDGES AND ALL MOVING PARTS.
14. USE INSULATED SURFACES. A double-insulated or grounded drill may be made live if the
bit comes in contact with live wiring in a wall, floor, ceiling, etc. Always check the work
area for live wires.
15. STAY ALERT. Watch what you are doing and use common sense. Do not operate drill
when you are tired.
6

EXTENSION CORD CHART
When an extension cord is used, it should also be a 3 wire cord to permit proper grounding of
the drill. As the distance from the supply outlet increases, heavier gauge extensions are
required. The use of extension cords of inadequate size wire causes a serious drop in voltage,
loss of power and possible motor damage. This table is based on limiting line voltage drop to 5
volts at 150% of rated amperes.
IF USING AN EXTENSION CORD OUTDOORS, BE SURE IT IS MARKED WITH THE SUFFIX
“W-A” (“W” IN CANADA) TO INDICATE THAT IS IS ACCEPTABLE FOR OUTDOOR USE.
Ampere rating 0- 2.10- 3.5- 5.10- 7.10- 12.1- 16.1-
(on Nameplate) 2.00 3.4 5.00 7.0 12.0 16.0 20.0
Ext. Cable Length Wire Size
25 Ft. 18 18 18 18 16 14 12
50 Ft. 18 18 18 16 14 12 10
75 Ft. 18 18 16 14 12 10 8
100 Ft. 18 16 14 12 10 8 8 Not
150 Ft. 16 14 12 12 8 8 6 normally
200 Ft. 16 14 12 10 8 6 4 available
300 Ft. 14 12 10 8 6 4 4 as flexible
400 Ft. 12 10 8 6 4 4 2 extension
500 Ft. 12 10 8 6 4 2 2 cord.
600 Ft. 10 8 6 4 2 2 1
800 Ft. 10 8 6 4 2 1 0
1000 Ft. 8 6 4 2 1 0 0
7

GROUNDING INSTRUCTIONS
This drill should be grounded while in use to protect the operator from electric shock. The drill
is equipped with an approved three-conductor cord and three-prong, grounding-type plug to fit
the proper grounding-type receptacle. The green conductor in the cord is the grounding wire.
Never connect the green wire to a live terminal.
NOTE: RECEPTACLE MUST BE GROUNDED FOR SAFE USE OF ADAPTER: IF IN
DOUBT CALL A QUALIFIED ELECTRICIAN AND HAVE THE RECEPTACLE
CHECKED FOR GROUND.
To connect twist locking plugs like those shown in figures A and B, insert the plug into a matching out-
let. When the plug is fully inserted, turn it clockwise until it locks. This prevents the plug from being
pulled out accidentally. To remove the plug, twist it counterclockwise to unlock it and remove it from
the outlet.
COVER OF COVER OF
GROUNDED GROUNDED
OUTLET BOX OUTLET BOX
Grounding Blade Grounding Blade
NEMA
L5-20
PLUG AND RECEPTACLE
FIGURE A
NEMA
L6-20
PLUG AND RECEPTACLE
FIGURE B
8

DS 800 Drill Stand - Parts List
Part No. Description Qty.
541 40 05-62 HU (100A) Carriage Assembly Red, with Handles 1
541 40 38-92 D (100A) Carriage Assembly Blue, with Handles 1
541 40 05-06 HU (110A) Carriage Body, Red 1
541 40 38-78 D (110A) Carriage Body, Blue 1
541 40 05-05 (111) Long Wear Plate 2
541 40 22-57 (C274) Screw, Brass Flat Head 8-32 x 5/16" 10
541 40 04-98 (113) Key, 1/2 x 1/2 x 6" 1
541 40 37-76 (C275) Screw, Flat Head, 8-32NC x 3/4" 1
541 40 04-71 HU (120A) Pinion Bracket Assembly 1
541 40 38-86 D (120A) Pinion Bracket Assembly 1
541 40 04-62 HU (121A) Pinion Bracket Body 1
541 40 38-76 D (121A) Pinion Bracket Body 1
541 40 04-59 (122B) Pinion Gear w/Retaining Ring Groove 1
541 40 04-58 (123) Short Wear Plate 4
541 40 37-84 (C228) Setscrew Socket Head, 1/4-20 x 3/4" 8
541 40 36-43 (C287) Hex Key, 1/8" 1
541 40 37-91 (C175) Capscrew, Bracket Mtg. 5/16-18 x 1-1/4" 8
541 20 52-40 (C59) Lock Washer, 5/16" 8
541 40 04-57 (127) Large Bronze Bearing 1
541 40 04-56 (128) Small Bronze Bearing 1
541 40 14-72 (295) Retaining Ring, Pinion 1
541 40 04-47 HU (130A) Lower Bracket Assembly 1
541 40 38-87 D (130A) Lower Bracket Assembly 1
541 40 04-41 HU (131A) Lower Bracket Body 1
541 40 38-77 D (131A) Lower Bracket Body 1
541 40 04-40 (132) Lock Screw 1
541 40 04-13 (139) Spacer Block, 2" 1
541 40 04-11 (142) Handle Rod, 8" 4
541 40 25-13 (144) Hub 1
541 40 37-82 (C253) Bolt, Hub Mtg., 1/2-13 x 2-1/4" 1
541 40 37-81 (C254) Lock Nut, Thin 1/2-13 1
541 40 25-74 (158C) Column, 42" 1
541 40 24-73 (159A) Rack, 42" Column, Weld Type 1
541 40 11-37 (165) Jackscrew, 1-1/4 - 7 1
541 40 12-40 (170) Motor Mounting Adapter Assembly 1
541 40 12-77 (171) Key, 3/8 x 3/8 x 4" 1
541 40 12-83 (172) Adapter Body 1
541 40 37-71 (C341) Capscrew, Motor Mtg. 1/4-28 x 1" 4
541 40 37-89 (C2) Capscrew, Adapter Mtg. 3/8-16NC x 1-1/2" 4
541 40 37-74 (C294) Capscrew, Motor Mtg. 1/4-20NC x 1" 4
Drill Stand Parts List
9

DS 800 Drill Stand - Parts List
Part No. Description Qty.
541 40 12-32 HU (180) Narrow Base Assembly 1
541 40 38-95 D (180) Narrow Base Assembly 1
541 40 35-19 (C490) Leveling Screw, 3/4-10NC x 4" 4
541 40 11-36 HU (184A) Large Base Assembly - Combination Anchor/Vacuum 1
541 40 38-97 D (184A) Large Base Assembly - Combination Anchor/Vacuum 1
541 40 11-26 (187A) Wheel Assembly, Large Base & Narrow Base 1
541 40 00-64 (188) Angle Bracket, Column to Base 1
541 40 11-23 (189A) Axle Bracket, Large Base & Narrow Base 1
541 40 37-31 (C8) Bolt, Hex Head, 1/2-13 x 1" 2
541 40 37-98 (C10) SAE Washer, 1/2" 2
541 40 11-07 (195A) Column, 60" 1
541 40 11-05 (197A) Column, 72" 1
541 40 17-91 (752008) Wheel, 5" 2
541 40 35-23 (C46) Cotter Pin, 1/8 x 1" 4
541 40 22-37-(C48) Washer, 5/8" 4
VACUUM ASSEMBLY
541 40 14-25 (302) Cross Bar 1
541 40 14-05 (303) Pad Stud, 3/4-10 x 8" 1
541 40 37-48 (304) Nut, Pad Stud, 3/4-10 1
541 40 19-32 (310) Vacuum Pad with Gasket 1
541 40 19-30 (311) Pad Gasket 1
541 40 19-01 (312) Quick Disconnect Stem, 1/4 NPT 1
541 40 18-99 (313) Pipe Plug, 1/4 NPT 1
541 40 00-57 (330) Single Pad Vacuum System 1
541 40 00-55 (340) Dual Pad Vacuum System 1
541 40 16-07 (406) Vacuum Pump, w/Fittings 1
541 40 16-02 (407) Vacuum Pump, Gast #DOAV111-AA 1
541 40 15-96 (408) Water Trap 1
541 40 15-92 (409) Pump Frame 1
541 40 15-90 (410) Vacuum Pump, 220/240 Volt 1
541 40 15-08 (441) Hose Assembly, Pad 2
541 40 14-95 (445) Valve, Vacuum Release 1/4 NPT 1
541 40 14-93 (446) Valve, Single Pad, 1/4" 1
541 40 14-91 (447) Vacuum Gauge 1
541 40 24-23 (A41) Close Nipple, 1/4 NPT 4
541 40 24-22 (A42) Tee, 1/4 NPT 3
541 40 23-58 (A602) Ell, 1/4 NPT 1
541 40 23-59 (A636) Nipple, 1/4 x 7 NPT 1
541 40 37-85 (C223) Capscrew, 10-32 x 1/2" 4
Drill Stand Parts List
10

DS 800 Drill Stand - Parts List
Part No. Description Qty.
VACUUM ASSEMBLY - COMBO BASE
541 40 00-77 (752225) Vacuum Pump w/Fittings and Slot Cap 1
541 40 16-02 (407) Vacuum Pump Only 1
541 40 16-40 (752226A) Bracket, Pump to Base 1
541 40 24-23 (A41) Nipple 1/4 x Close Pipe 3
541 40 15-96 (408) Water Trap 1
541 40 24-22 (A42) Tee, 1/4 Pipe 2
541 40 16-35 (752227) Hose, Pump to Slot Cap 1
541 40 14-91 (447) Vacuum Gauge 1
541 40 14-95 (445) Release Valve 1
541 40 16-56 (752221) Gasket, Combo Base 1
541 40 16-51 HU (752222) Slot Cap 1
541 40 39-27 D (752222) Slot Cap 1
541 40 16-46 (752223) Gasket, Slot Cap 1
541 40 37-85 (C223) Capscrew, Bracket to Pump, 10-32 x 1/4" 4
541 40 37-31 (C8) Bolt, Bracket to Base, 1/2-13 x 1" 1
541 40 37-98 (C10) SAE Washer, 1/2" 1
SWITCHBOX ASSEMBLY
541 40 10-37 (223) Receptacle, 20A, Single 1
541 40 36-77 (227) Strain Relief 1
541 40 10-18 (229) Switch, Motor 1
541 20 19-11 (230) Boot, Auxiliary Switch 1
541 40 10-03 (237) Boot, Motor Switch 1
541 40 09-99 (238) Switch Plate 2
541 20 19-07 (248) Ammeter, 0-30A 1
541 40 14-46 (473) Mounting Bracket, DS 800 Carriage 1
541 40 14-44 (474) Clip - Male Dovetail 1
541 40 14-42 (475-1) Box - Front 1
541 40 14-40 (475-2) Box - Back 1
541 40 14-38 (476) Receptacle, 15A, Single 1
541 40 14-36 (477) Plug, 30A, Twist Lock 1
541 40 16-08 (30622) Switch, Auxiliary 1
541 40 37-94 (C139) Lock Nut, 1/4-20 2
541 40 22-70 (C231) Capscrew, Socket 1/4-20 x 1/2" 2
541 40 36-15 (C255) Jam Nut, 1/2-20 1
541 40 37-67 (C375) Capscrew, Button Head 10-32 x 1/4" 4
541 40 37-66 (C376) Capscrew, Button Head 6-32 x 3/8" 2
541 40 37-64 (C378) Capscrew, Button Head 8-32 x 3/8" 2
541 40 36-14 (C383) Jumper, Switch 1
Drill Stand Parts List
2812 Carriage
11
541 40 10-35 (225) 20A,

DS 800 Drill Stand - Parts List
Part No. Description Qty.
ANGLE BRACKET ASSEMBLY
541 40 00-62 (105) Angle Bracket Assembly
541 40 05-40 (106) Upper Backstay Bracket 1
541 40 16-94 (752051) Lower Backstay Bracket 1
541 40 16-88 (752052) Lower Backstay 1
541 40 16-83 (752053) Upper Backstay 1
541 40 16-77 (752054) Backstay Jam Nut 1
541 40 16-66 (752056) Adapter - Upper Backstay Rod 1
541 40 37-98 (C10) SAE Washer, 1/2" 2
541 40 37-88 (C20) Lock Nut, 3/8-16 1
541 40 37-35 (C70) SAE Washer, 5/8" 2
541 40 37-34 (C71) Lock Nut, 5/8-11 2
541 40 37-32 (C79) Bolt, Hex Head, 3/8-16 x 1-1/4" 1
541 40 37-77 (C273) Bolt, Hex Head, 1/2-13 x 1-1/4" 2
541 40 35-91 (C442) Bolt, Hex Head, 5/8-11 x 2-1/4" 1
541 40 35-92 (C497) Bolt, Hex Head, 1-1/4-7 x 1-1/2" 1
541 40 35-93 (C498) SAE Washer, 1-1/4" 1
541 40 35-94 (C499) Bolt, Hex Head, 5/8-11 x 4-1/4" 1
OPTIONAL ROLLER CARRIAGE
541 40 15-07 HU (250A) Roller Carriage Assembly 1
541 40 38-91 D (250A) Roller Carriage Assembly 1
541 40 15-35 HU (258) Carriage Body 1
541 40 38-42 D (258) Carriage Body 1
541 40 04-98 (113) Key 1
541 40 37-76 (114) Machine Screw 1
541 40 15-23 (254A) Bearing, Carriage Body Roller 4
541 40 15-25 (255) Carriage Roller Assembly with Bearing 2
541 40 15-22 (256 ) Roller Shaft, Carriage Body 2
541 40 22-75 (C219) Setscrew 10-24 x 3/8" 2
541 40 37-32 (C79) Bolt, 5/8-16 x 1-1/4" 4
541 40 15-51 (268) Side Roller Housing 4
541 40 15-44 (262) Shaft, Side Roller 4
541 40 15-41 (264A) Bearing, Side Roller 8
541 40 15-38 (265) Side Roller Assembly with Bearing 4
541 40 15-57 (269) Rubber Spacer - Side Roller 4
541 40 37-60 (C385) Setscrew 1/4-20 x 1/2" 4
541 40 36-25 (C422) Capscrew 10-24 x 3/4" 16
Drill Stand Parts List
12

DS 800 Drill Stand - Parts List
Part No. Description Qty.
OPTIONAL ROLLER CARRIAGE - Cont'd.
541 40 15-64 HU (270) Upper Roller Housing Assembly 1
541 40 38-88 D (270) Upper Roller Housing Assembly 1
541 40 15-62 HU (271) Housing Only 1
541 40 38-79 D (271) Housing Only 1
541 40 15-46 (272) Eccentric Roller Adjuster 4
541 40 15-40 (274A) Bearing, Roller 4
541 40 15-37 (275) Adjustable Roller Assembly with Bearing 4
541 40 15-33 (276) Shaft, Eccentric Adjustment Roller 2
541 40 15-31 (277) Roller Spacer 2
541 40 15-27 HU (280) Lower Roller Housing Assembly 1
541 40 38-89 D (280) Lower Roller Housing Assembly 1
541 40 15-17 HU (281) Housing Only 1
541 40 38-40 D (281) Housing Only 1
541 40 15-15 (282) Lock, Carriage 1
541 40 37-53 (C421) Setscrew, 1/4-20 x 3/8 4
541 40 37-44 (C486) Capscrew, 5/16-18 x 1-1/4" 8
541 20 52-40 (C59) Lock Washer, 5/16 Internal Tooth 8
541 40 15-00 HU (290) Pinion Bracket Assembly 1
541 40 38-90 D (290) Pinion Bracket Assembly 1
541 40 14-81 HU (291) Bracket, Only 1
541 40 38-41 D (291) Bracket, Only 1
541 40 37-54 (C419) Setscrew, 1/4-20 x 5/16 1/2 Dog Point 1
541 40 14-76 (292A) Bearing, Pinion Gear, Small 1
541 40 14-74 (293A) Bearing, Pinion Gear, Large 1
541 40 04-59 (122B) Pinion Gear, w/Retaining Ring Groove 1
541 40 14-72 (295) Retaining Ring 1
541 40 04-11 (142) Handle 4
541 40 25-13 (144) Hub 1
541 40 37-82 (C253) Bolt, 1/2-13 x 2-1/4" 1
541 40 37-81 (C254) Locknut, 1/2-13 Thin 1
541 40 14-68 (297) Stud, 1/4-20 x 1/4-28 x 1 4
541 40 22-89 (C16) Washer, 1/4 SAE 4
541 40 37-52 (C424) Jam Nut, 1/4-28 4
Drill Stand Parts List
13

Item Number Part Number
1 541 40 11-37 (165)
2 541 40 04-13 (139)
(Includes key)
3 541 40 37-74 (C-294)
Milwaukee mount
541 40 37-71 (C-341)
DeWalt mount
541 40 02-77 (73234)
Cardi mount
4 541 40 12-40 (170)
(Includes key and
hardware)
541 40 12-83 (172)
(Adapter only)
5 541 40 12-77 (171)
6 541 40 37-76 (C275)
7 541 40 04-98 (113)
8 541 40 25-74 (158C) 42”
541 40 11-09 (190A) 60”
541 40 11-07 (195A) 72”
541 40 11-05 (197A) 80”
9HU 541 40 12-32 (180)
9D 541 40 38-95 (180)
10HU 541 40 05-62 (100A)
10D 541 40 38-92 (100A)
11 541 40 35-19 (C-490)
12HU 541 40 11-36 (184A)
12D 541 40 38-97 (184A)
13 541 40 11-26 (187A)
14 541 40 37-38 (C-10)
15 541 40 37-31 (C-8)
16 541 40 17-91 (752008)
17 541 40 11-23 (189A)
1
2
4 5 6
7
8
9HU/D
11
12HU/D
15 14 13
10HU/D
3
16 17
14

1
2
3
4
5
6
7
89HU/D
10
11
12
13
14
15
16HU/D
17
18
19
20
21
22
23
24
25
26
27
28 29HU/D
Item Number Part Number
1 541 40 04-58 (123)
2 541 40 22-57 (C-274)
3 541 40 37-54 (C-419)
4 541 40 37-91 (C175)
5 541 20 52-40 (C-59)
6 541 40 37-84 (C-228)
7 541 40 14-72 (295)
8 541 40 04-56 (128)
9HU 541 40 04-62 (121A)
9HU Assy 541 40 04-71 (120A)
9D 541 40 38-76 (121A)
9D Assy 541 40 38-86 (120A)
10 541 40 04-59 (122B)
11 541 40 04-57 (127)
12 541 40 37-81 (C-254)
13 541 40 25-13 (144)
14 541 40 04-11 (142)
15 541 40 37-82 (C-253)
16HU 541 40 05-06 (110A)
16D 541 40 38-78 (110A)
17 541 40 37-76 (C-275)
18 541 40 04-98 (113)
19 541 40 37-89 (C-2)
20 541 40 05-05 (111)
21 541 40 22-57 (C-274)
22 541 40 04-58 (123)
23 541 40 22-57 (C274)
24 541 20 52-40 (C-59)
25 541 40 37-91 (C-175)
26 541 40 04-40 (132)
27 541 40 36-43 (C-287)
28 541 40 37-84 (C-228)
29HU 541 40 04-41 (131A)
29HU Assy 541 40 04-47 (130A)
29D 541 40 38-77 (131A)
29D Assy 541 40 38-87 (130A)
Carriage Assembly
541 40 05-62 HU / 541 40 38-92 D
15
Lock Screw

Item Number Part Number
1 541 40 37-48 (304)
2 541 40 15-92 (409)
3 541 40 18-99 (313)
4 541 40 19-32 (310)
(Includes gasket)
5 541 40 19-30
6 541 40 19-01
7 541 40 14-05
8 541 40 14-25
1
2
3
4
5
6
7
8
Single Pad Vacuum System
541 40 00-57
Dual Pad Vacuum System
541 40 00-55
16

1
2
3
4
5
6
7
8
9
10 11 12 13 14
15
16
17
18
19
20
21
22
26
27
28 29
30
Item Number Part Number
1 541 40 14-91 (447)
2 541 40 24-22 (A 42)
3 541 40 24-22 (A 42)
4 541 40 15-08 (441)
5 541 40 24-23 (A 41)
6 541 40 15-96 (408)
7 541 40 16-02 (407)
8 541 40 15-92 (409)
9 541 40 37-85 (C223)
10 541 40 15-08 (441)
11 541 40 14-93 (446)
12 541 40 23-58 (A602)
13 541 40 23-59 (A636)
14 541 40 24-22 (A42)
15 541 40 14-95 (445)
Item Number Part Number
16 541 40 14-91 (447)
17 541 40 24-22 (A42)
18 541 40 14-95 (445)
19 541 40 24-23 (A41)
20 541 40 24-22 (A42)
21 541 40 24-23 (A41)
22 541 40 15-96 (408)
23 541 40 16-35 (752227)
24HU 541 40 16-51 (752222)
24D 541 40 39-27 (752222)
25 541 40 16-46 (752223)
26 541 40 37-31 (C8)
27 541 40 37-98 (C10)
28 541 40 16-40 (752226A)
29 541 40 16-56 (752221)
30 541 40 22-34 (C494)
31 541 40 15-72 (412)
Vacuum Pump Assembly
Single & Dual Pad Vacuum System
541 40 16-07
Vacuum Assembly Combo Base
541 40 00-77HU
541 40 39-29D
23
24HU/D
25
17
31

Switch Box Assembly
541 40 40-16
Item Number Part Number Item Number Part Number
1 541 40 10-37 (223) 12 541 40 22-70 (C231)
2 541 20 19-07 (248) 13 541 40 14-44 (474)
3 541 40 16-08 (30622) 14 541 40 14-46 (473)
4 541 40 14-38 (473) 15 541 40 37-94 (C139)
5 541 40 10-35 (225) 16 541 40 36-15 (C255)
6 541 40 10-18 (229) 17 541 40 37-67 (C375)
7 541 40 36-77 (227) 18 541 40 37-64 (C378)
8 541 40 09-99 (238) 19 541 40 37-66 (C376)
9 541 40 10-03 (237) 20 541 40 36-14 (C383)
10 541 40 14-42 (475-1)
11 541 40 14-40 (475-2)
1
2
8
9
10
19
7
18
3 4 5
6
20
11
17
12 13 14 15 16
18

1
2
3
4
5
White
Green
Black
Switch Box Assembly
541 40 40-16
Item Number Description
1 Receptacle 20A Single
2 Ammeter 0-30 Amp
3 Switch
4 Panel Receptacle 15 Amp
5 Plug, 20 Amp 125 Volt
6 Switch
7 Strain Relief
6
7
Switch Box Wiring Schematic
19