Technogym Leg Curl User manual

1
S E L E C T I O N
T H E S T R E N G T H E V O L U T I O N
Leg Curl
User manual
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

2
A
E
C
BD
Contents
Leg Curl
Identification of the manufacturer and equipment
The identification plate of the equipment and manufacturer, affixed behind the seat, gives the
following details:
AName and address of the manufacturer
BCE Mark
CSerial number
DWarning
EEquipment classification
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

3
G
03006011
H
B
C
D
E
A I LF
Contents
Leg Curl
Description of the equipment
A Seat: where the user sits to perform the exercise. Its position can be adjusted using the
lever (I).
B Lever: operated by the user by means of the roller (C); before starting to exercise, or
between one set and the next, the starting position can be adjusted so as to modify the
range of motion by using the ROM device.
D ROM device: system for adjusting the Range of Motion and the starting position.
Adjustments are made by means of the ROM lever (E) after having released it by operating
the button positioned on it.
F Weight stack: the lever (B), operated by the user, moves the weights along two guides
by means of a cable. A pin (G) is used for selecting the load, to adjust the exercise effort
level. The cursor (H) is used to vary the selected workload by 2,5 kg.
L Side handgrips: the user can enhance the comfort by holding them during the exercise.
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

4
Contents
Leg Curl
Technical data
1410 mm
(58")
+
284 kg (632 lb)
+
125 kg (250 lb)
1130 mm
(44.5")
1070 mm
(42")
254 kg (565 lb)
95 kg (190 lb)
1485 mm
(58")
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

5
A
B
C
99834109
Contents
Leg Curl
Accessories
The equipment’s standard outfit comprises:
- User manual
- Warranty certificate
Optional accessories are the wheels (A)
for moving the equipment (A0000015), the
Basic Box service kit (B) (A0000010) and
the number holder (C) (H0000369) to be
assembled between the top and the weight
stack guides.
Warning
There may be only one or two castor
wheels, depending on the type of
equipment.
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

6
B
A
Contents
Leg Curl
Assembling the number holder
The number holder must be assembled
immediately underneath the top: Standing
facing the equipment, affix the number holder
on the left tube supporting the guide, so that
it is flush with the rubber stop of the guide.
The number holder is divided into two pieces:
the larger section (A) goes on the front, while
the crescent closure (B) goes on the back of
the equipment.
Insert the two screws (M5x6 Z) from the front
of the equipment, mating them with the two
M5 cap nuts at the rear; then lock down using
the appropriate spanners.
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

7
Contents
Leg Curl
Safety devices and notices
The equipment does not have any sharp corners.
All the parts which come into contact with the body are adequately protected with rubber
coverings or padding.
The weight stack is enclosed in protective panels.
Warning
It is important to pay attention to the labels affixed to the equipment, as they
provide information about possible risks and hazards.
Pay particular attention to the parts of the
equipment with labels indicating “DANGER
OF SQUASHING”.
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

8
Contents
Leg Curl
Packing
The equipment is supplied fully assembled in a carton and protected by cellophane wrapping,
and secured to a pallet.
The equipment can be lifted and handled using normal lifting machine.
In order to ensure the safety of persons and property, carefully determine the lifting and
handling machine used as a function of the place of installation.
OK
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

9
Contents
Leg Curl
Place of installation
To guarantee safe, comfortable and effective use of the equipment, the place of installation
must comply with certain specific requirements; in particular, before choosing where to install
the equipment it is recommended to check the following:
- the temperature is between +10°C and +25°C;
- enough air is circulating to keep humidity during exercise to between 20% and 90%;
- the lighting is good enough to make the area safe and relaxing place to exercise in;
- sufficient clearance on all sides of the equipment, taking into account its maximum
dimensions during the movements, necessary for safety reasons;
- a flat, stable and vibration-free floor surface, with adequate carrying capacity for the
equipment’s weight.
If the equipment is to be installed in a public recreation area, the place of installation must
comply with all binding regulations.
Warning
The equipment must be installed and used in a place whose access and supervision
are specifically controlled by the owner.
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment

10
01083013AA
Contents
Leg Curl
Unpacking
The equipment is supplied on a pallet, to which it is secured by means of straps.
To remove the equipment from the packing:
- cut the carton along the bottom and pull it away from the top;
- remove the cellophane by pulling it away from the top;
- until the straps securing the equipment to the pallet;
- lift the equipment from the weight stack side and place it on the ground.
cont.
Identification of the manufacturer
and equipment
Description of the equipment
Technical data
Accessories
Assembling the number holder
Safety devices and notices
Packing
Place of installation
Unpacking
Lifting and handling the
equipment
Adjusting the equipment
Routine maintenance
Replacing the padded
components
Replacing the cable
Adjusting cable tension
Disassembling the front protective
weight stack panel
Technical Service
Codes for original spare parts
Storage
Disposing of the equipment
Using the equipment