Terratek TPDC18134K User manual

User Manual – Please read and retain for future reference.
Cordless Drill
TPDC18134K

Exploded Assembly Diagram
1 2 3 45 6 7 8 9 10 11 12 13
14 15 16 17-2
17-1 17-3 18 19-1 19-2

1
2
3
4
5
6
Chuck
Torque control ring
For. /Rev./Lockout
On/Off/Var.speed switch
Battery
Battery clip
3
6
5
1
2
4
Fig.1

1
Contents
Parts List
Technical Information
Safety Instructions
Using your drill
Maintenance
Warranty Parts List
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
17-1
17-2
17-3
18
19-1
19-2
Anti-screw
Chuck
Gear unit
Torque
Inner torque
Motor gear
Screw
Motor
Shell of machine
Battery
Switch
Handspike
Level bubble
Screw
Clip
Double end bit
LED
Light
Light circuitry board
Resistance
Decorative cover
Adapter
Charger Base

Technical Information
Copyright© 2011 by ACL Group (Intl) Ltd. All rights reserved. This manual or any artwork
contained herein must not be reproduced in any shape or form without the express
written consent of Terratek Intl. Ltd. Diagrams within this manual may not be drawn
proportionally. Due to continuing improvements, actual product may differ slightly
from the product described herein.
Read this entire manual before using this
product. Failure to do so can result in serious injury. Save
this manual for future reference.
2
Voltage: 18V DC
Battery: Ni-Cd 0.8Ah
No load speed: 0-550RPM
Torque control: 16 positions
Chuck: 0.8-10mm
Charger: 3-5 hours
Weight NW/GW: 4.3 /7.27 lbs

Read and Keep This Manual
Please read carefully all instructions within this manual. Failure to follow all safety warnings can result
in serious personal injury. The term “Power Tool” in all of the following warnings refers to your mains
operated (corded) or battery operated (cordless) power tool.
Important SAFETY Information
General Safety Rules
WARNING! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term “power tool” in
all of the warnings listed refers to corded or cordless power tools.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
Before use, ensure that the power outlet you are using matches the plug on your power tool and that
the voltage of the outlet matches that of your power tool.
This symbol is to warn you of potential personal
injury hazards. Please read carefully the notes along side this
warning to avoid possible injury or death.

Only use grounded extension cords with power tools fitted with proper plugs and if using outdoors
ensure any extension cord is suitable for outdoor use.
Always try to avoid body contact with grounded surfaces, such as radiators, cooking ranges and any
other fixed appliance with metal surfaces.
Do not expose your power tool to wet or damp conditions and NEVER use in rain.
Check regularly the power cord of your machine and any extension cord that you are using for damage.
Do not carry or pull the machine with the power cord.
Ensure the cord is clear from hot surfaces, oil or sharp objects.
Personal safety
Never use your power tool whilst under the influence of alcohol, drugs or medication.
Tiredness can often cause accidents, stay alert.
Never use your power tool without the correct guards in place.
Always use ANSI approved eye protection and dust mask. Non slip safety shoes and hearing protectors
should be worn at all times when using your power tool.
Ensure any dust collecting device supplied with your power tool is connected correctly before use.
Ensure all loose clothing, long hair or jewelry is kept clear of the power tool.
Before plugging your power tool into the power outlet ensure the power tool is in the OFF position.
Check that wrenches or adjusting keys have been removed. Any wrench or key left attached to a moving
part can result in injury.
Power tool use and care.
Keep your power tool clean and well serviced at all times.
Never adjust or service any power tool before disconnecting from the mains electricity supply.
Always use the correct tool for the job.
Never force the tool to work harder than it is designed to do.
Never use your power tool with broken parts such as switches, guide fences or leg stands.
ALWAYS keep your power tools away from children.
Keep cutting tools sharp to ensure less stress on the motor.
Only have your power tool serviced by a qualified repair agent using manufacturers recommended parts.
WARNING: For your own safety read Instruction Manual before operating your tool.
A) Wear eye protection.
B) Keep hands away from drill bit.
C) Do not operate without guards in place.
D) Do not perform any operation freehand.
E) Never grab chuck while it is turning.
F) Turn off tool and wait for tool to stop before moving workpiece or changing settings.
G) Remove battery before changing drill bit or servicing.
Safety Instructions
Read this owner's manual completely and make sure you understand all of its safety
guidelines.

1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS & WRENCHES. Before turning on the power tool, make sure the keys
and adjusting wrenches have been removed.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. ALWAYS REMAIN ALERT WHEN THE SAW IS IN USE. Inattention on the part of the operator may
lead to serious injury.
5. DON’T USE IN A DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations or
expose them to rain. Keep work area well lit.
6. KEEP CHILDREN AWAY. All visitors should remain at a safe distance from work area.
7. MAKE WORKSHOP CHILD-PROOF with padlocks, master switches or by removing starter keys.
8. USE THE RIGHT TOOL. Don’t force a tool or attachment to do a job for which it was not designed.
9. USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
10. DON’T FORCE THE TOOL. It has been designed to operate at maximum safety and performance
levels.
11. DO NOT FORCE THE MATERIAL BEING CUT. Always let the blade cut at its own speed.
12. WEAR PROPER APPAREL. Do not wear loose clothing, neckties, rings, bracelets or other jewelry
which may get caught in moving parts. Non-slip foot wear is recommended. Wear protective hair
covering if you have long hair.
13. ALWAYS USE SAFETY GLASSES. Also use face or dust mask for commercial cutting operations.
Everyday eyeglasses only have impact-resistant lenses, they are NOT safety glasses.
14. SECURE WORK. Use clamps or a vise instead of your hand to hold work when practical. This safety
precaution allows for proper tool operation using both hands.
15. DON’T OVERREACH. Keep proper footing and balance at all times.
16. MAINTAIN TOOLS WITH CARE. Keep tools clean and in good working condition for maximum
safety performance. Follow instructions for lubricating and changing accessories.
17. DISCONNECT TOOLS BEFORE SERVICING – when changing accessories, such as blades, bits,
cutters, etc.
18. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in OFF position before
plugging in.
19. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories.
The use of improper accessories may increase risk of injury.
20. MAKE SURE YOU USE THE CORRECT TOOL for the job you are doing.
21. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
22. CHECK DAMAGED PARTS. Before further use of the tool, damaged part(s), (i.e., guard) should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other
condition that may affect the saw’s operation. A guard or other part that is damaged should be properly
repaired or replaced.
23. Replace damaged bits immediately. DO NOT USE DAMAGED BITS. They may cause bodily injury.
24. DIRECTION OF FEED. Feed work into the blade against the direction of rotation of the blade only.
25. DO NOT ALTER THE PLUG.
26. NEVER LEAVE TOOL RUNNING UNATTENDED. Turn power off. Don’t leave tool until it comes to a
complete stop.
This power tool is supplied with all the relevant safety guards and features, it should be checked
before every operation, and this manual should be read and kept in a safe place. Whilst we warn
of all the possible risks attached to using power tools any operator must have read and
understood the manual and apply their own caution and common sense when using this power
tool.
Following this guide will greatly reduce your risk of electric shock or injury.

Only use qualified repair agents to service this power tool.
Only use qualified electrician to repair any damaged wiring.
NEVER remove the grounding prong from the power toll or extension cord.
Power Extension Cords
When using any extension cord the machine will suffer a power reduction due to the drop in voltage
caused by the length of the cord. This can be partially offset by selecting extension cords with lower
gauge wire.
Check all extension cords for damage before use.
Avoid sharp objects.
Do not position the cord where it could be subject to traffic passing over it.
Symbols
IMPORTANT: Some of the following symbols may be used on your tool.
V…………………………volts
A…………………………amperes
Hz……………………….hertz
~…………………….….alternating current
…/m……………….....revolutions per minute
回 .....................class II construction (double insulated)
Kg………………………..kilograms
n0………………………..No load speed
CE ………………….……Conforms to European Harmonised New Approach Directives
DC ………………..…….Direct Current
Unpacking
Carefully remove the product and any accessories from the box. Make sure that all items listed in the
packing list are included.
Packing List
A) Drill
B) Battery
C) Charger
Battery use and care
A battery operated tool with integral batteries or a separate battery pack must be recharged
only with the specified charger for the battery.
A charger that may be suitable for one type of battery may create a risk of fire when used with another
battery.
Use battery operated tool only with specifically designed battery pack.
Use of any other batteries may create a risk of fire.
NEVER place hands or other body parts near the drill bit or chuck during operation.
Hold the drill by its handle only. Because the cordless driver drill operates by battery power, be aware of
the fact that it can begin to operate at any time.

When battery pack is not in use, keep it away from other metal objects like paper clips, coins,
keys, nails, screws, or other small metal objects that can make a connection from one
terminal to another. Shorting the battery terminals together may cause burns or a fire.
Charging the battery pack
Charge battery for 3-5 hours only, when you plug battery into the charger the “GREEN” light will come
on, there is no light to indicate the battery is fully charged, charge only for 3 to 5 hours,
unplug charger and remove battery from charger.
Battery charger LED function
Charger plugged in: Red light “ON”
Battery charging: Green light “ON”
WARNING: Improper use of the battery or battery charger can lead to serious injury.
To avoid these injuries:
A) NEVER disassemble the battery.
B) NEVER incinerate the battery, even if it is damaged or is completely worn out.
The battery will explode in a fire.
C) NEVER short-circuit the battery.
D) NEVER insert any objects into the battery charger’s air vents. Electric shock or damage to the
battery charger may result.
E) NEVER charge outdoors. Keep the battery away from direct sunlight and use only where there is low
humidity and good ventilation.
F) NEVER charge when the temperature is below 0°C (32°F) or above 40°C (104°F).
G) NEVER connect two battery chargers together.
H) NEVER insert foreign objects into the hole for the battery or the battery charger.
I) NEVER use a booster transformer when charging.
J) NEVER use an engine generator or DC power to charge.
K) NEVER store the battery or battery charger in places where the temperature may reach or exceed
40°C (104°F).
L) ALWAYS operate charger on standard household electrical power (230 volts).
Using the charger on any other voltage may overheat and damage the charger.
M) ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.
N) ALWAYS disconnect the power cord from its receptacle when the charger is not in use.
EXCHANGING THE BATTERY PACK
Removing battery pack: Press the two buttons (Fig.1) and slide the battery pack down to remove.
Inserting battery pack: Slide the battery pack into the holder on the underside of the handle until it
latches into place.
Using your drill
VARIABLE SPEED CONTROLLED TRIGGER SWITCH
Your tool is equipped with a variable speed trigger switch (Fig.1). The tool speed can be controlled from
the minimum to the maximum nameplate RPM by the pressure you apply to the trigger. Apply more
pressure to increase the speed and release pressure to decrease speed.
FORWARD/REVERSING LEVER & TRIGGER LOCK
Your tool is equipped with a forward/ reversing lever and trigger lock (Fig.1) located above
the trigger. This lever was designed for changing rotation of the chuck, and for locking the trigger in an
“OFF” position to help prevent accidental starts and accidental battery discharge. For forward rotation,

(with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever
to the far right. To activate trigger lock move lever to the center “off” position.
MOUNTING AND DISMOUNTING THE BIT
Mounting the bit
Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the
front) to open the clip on the keyless chuck. After inserting a driver bit, etc., into the keyless drill chuck,
tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front).
NOTE: If the sleeve becomes loose during operation, tighten it further.
The tightening force becomes stronger when the sleeve is tightened.
DISMOUNTING THE BIT
Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the
front), and then take out the bit.
DRILLING
Place the bit on the work surface and apply firm pressure before starting. Too much pressure will slow
the bit and reduce drilling efficiency. Too little pressure will cause the bit to slide over the work area and
dull the point of the bit. If the tool begins to stall, reduce pressure slightly to allow the bit to regain
speed. If the bit binds, reverse the motor to free the bit from the workpiece.
TORQUE ADJUSTMENT
By turning the adjustment ring (Fig.1) the required torque can be adjusted. The arrow aligns with the
adjusted state.
Maintenance
WARNING: To reduce the risk of injury, always unplug the charger and remove the battery
pack from the charger or tool before performing any maintenance. Never disassemble the tool,
battery pack or charger.
Disposal of the exhausted battery
WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated.
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the
end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into
the municipal waste stream. Check with your local solid waste officials for details in your area for
recycling options or proper disposal.
Disposal
Power tools, accessories and packaging should be sorted for environmentally-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical and electronic equipment and its
incorporation into national right, products that are no longer suitable for use must be separately
collected and sent for recovery in an environmentally-friendly manner.

Battery packs/batteries:
Ni-Cad:
Do not dispose of battery packs/batteries into household waste, water or fire. Battery packs/batteries
must be collected, recycled or disposed of in an environmentally-friendly way.
Only for EC countries:
Defective or dead batteries must be recycled according to the directive 2006/66/EC.
Declaration of Conformity
We ACL Group (Intl.) Ltd, England DN6 8LZ declare that the Cordless Drill has been manufactured
according to our full quality assurance procedures.
The declaration is to certify that it conforms to CE, EMC, MD and RoHS directives:
EN55014-1:2006
EN55014-2:1997 /+A1:2001 /+A2:2008
All provisions of Annex 1 of Council Directive 2004/108/EC – EMC directive
EN60335-1:2010
EN60335-2-2:2010
EN60745-2-1:2010
All provisions of Annex 1 of Council Directive 2006/42/EC – Machunery Directive
RoHs 2011/65/EU
Mr. Alan Garnett, UK QA Manager
Environmental Protection
RECYCLING: WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED OF WITH HOUSEHOLD WASTE.
PLEASE RECYCLE WHERE FACILITIES EXIST. CHECK WITH YOUR LOCAL AUTHORITY OR RETAILER FOR
RECYCLING ADVICE.
Ni-cd

Please read the following carefully
ACL Group (Intl) Ltd. and/or it’s distributor has provided the parts list and assembly diagram as a
reference tool only. Neither ACL Group (Intl). Ltd. or its distributor makes any representation or
warranty of any kind to the buyer that he or she is qualified to do any repairs or replace any parts of this
product. ACL Group (Intl) Ltd. and its distributor expressly state that all repairs or parts replacement
should be done by certified or licensed technicians. The buyer assumes all risk and liability arising out of
his or her repairs or parts replacement to the original product.
12 Months Limited Warranty
If within 12 months from the date of purchase you experience any problems with your product, please
return the product to its distributor/dealer for repair or replacement. This warranty DOES NOT COVER
normal wear, or any damage as a result of accidents, misuse, abuse or negligence.

ACL Group (Intl) Ltd
Doncaster, England
Email: [e-mail]
www.terratekintl.com