THERMORY BARRELS 62 User manual

Installation guide Barrel Nº62
BARRELS
© THERMORY 2021
Installation
Guide
These are assembly instructions for
standalone Thermory Barrel Sauna no 62,
which is meant for 6 people and
has a window.

Barrel Nº62
These installation guidelines are purely informative and
based on the best knowledge currently available, and they
should be used accordingly. We advise you to follow the
regulations of your country where they conflict with the
general recommendations found in this guide.

Installation guide Installation guideBarrel Nº62 Barrel Nº62
BARRELS BARRELS
PARTS 1
x3 x2
x2
x1
x1
x2 x4
x1
x6
x2
x1
x10
x2
x1
*if needed for
heater installation.
AH
J
B
D
F1
J1 V
C
O
J2
I
F
W
L
R
CRADLES 
TOP STAVE
INTERIOR
BENCHES
FRONT
PANEL
RIGHT
PANEL
SECTION
BENCH
SUPPORTING
LEGS
WIRE

ASPEN
ROOF
BOARD
BACKREST
STAVES
METAL
BANDS
LEFT PANEL
SECTION
DECORATIVE
ROOF NISHING
BOARDS
FLOORING
DUCKBOARD
ADHESIVE
ROOF TAPE
x1
CENTER
STAVE x80 (+1
reserve)
RIGHT

STAVES
PARTS 2
TOOLS

3 People
Recommended
+ +
x8 x70
x2
x2 x2x2
x2
x2 x2
x26´
24mm
Rubber
x4
x3 x3
x24
x120 x24
MP
UP1
NN1
SCREW
5.0X120
SCREW
4.0X50
Ø BOLT
16X140
HEX NUT

FLAT
WASHER
STAINLESS
STEEL SCREW
4.0X50
SCREW
4.2X70
STAINLESS
STEEL SCREW
4.2X70
STEP ZERO
Before you begin, be sure the

location.
Approximately 8’ x 8’ is ideal.
Overall dimensions are shown here.
Be sure the site is level and free of

Concrete, pavers or crushed stone
is preferred.
7´´6´
7´´4´
x1 x1
E E1
REAR
PANEL
REAR PANEL
WITH
WINDOW
x1 x2
ZZ1
WATERPROOF
ROOF COVER
WOODEN SLAT
FOR ROOF
COVER

Installation guide Installation guideBarrel Nº62 Barrel Nº62
BARRELS BARRELS
STEP ONE


will have no dowel. Carefully level for

Place the center stave (B)
on wooden dowels embedded

Fix the center stave (B)
with screw 4.2x70 (N).
STEP THREE
Place 6 sauna body staves (C, C1)
to each side of the center stave (B)

Body staves (C)

Be sure to align the panel

STEP TWO

from corner to corner.
Measurements “a” and “b” should be
equal to ensure the cradles are square.
Be sure cradles remain level.
STEP FOUR
Place door panel (D) in front slot.
Be sure panel is centered, leveled,

panels (F, F1) using 4 5.0 x 120
(M) screws and 2 4.2 x 70 (N1)
stainless steel screws.
Place rear panel (E) with bench



panel section (M), front panel (D)
and right panel section (M). These
panels must be completely seated
into the floor panel.
STEP FIVE
Place body staves (C) until the

with window (E1) on rear panel (E),

A
B
A=B
N
A
B
Centered
Back
Vent
Front
C
ME1
E
C
B
C1
N
x6 pcs x6 pcs
D
M
M
M
F
F1
N1
N1
E
M
M

Installation guide Installation guideBarrel Nº62 Barrel Nº62
BARRELS BARRELS
STEP SEVEN
Measure steel bands (I) to ensure
correct length of 276,” +/- 1/2” is
acceptable.
Install steel bands (I) by wrapping
bands around barrel prior to

Place steel bands evenly around
barrel, covering screw heads.
Measure from steel band to barrel
edge to ensure the steel band is
even.
Cover roof with roof tape.
Rub and smooth with pressure to
ensure adhesion.
Install interior aspen roof trim (O)
with 4.0 x 50 (P1) stainless steel
screws.
STEP EIGHT


on wall mounts using stainless steel
screws 4.2 x 70 (N1).
Hold the seat and leg assembly tight

sure the bench seat is level from
front to back. This will ensure proper
placement.

height using stainless steel screw
4.0 x 50 (P1).
STEP NINE
Install porch benches (K),
using screws 4.2 x 70 (N)
and 5.0 x 100 (X).
Hold the seat and leg
assembly tight to the sauna

sure the bench seat is level
from front to back. This will
ensure proper placement.
STEP SIX
Continue placing body staves (C)
tightly on both sides of the sauna

body staves on the front panel with
4.2 x 70 screws and rear window
panel with 4.0 x 50 screws to
prevent glass breakage.

the roof top joint, use top stave


WARNING!



P
N
H
R
I
O
P1


I

P1
N1

L


N1


N1
N1
C
.4” .6” .8” 1” 1.2”
Roof tape
Aspen
roof board
3-15/16´´
C

Installation guide Barrel Nº62
BARRELS
WATCH THE VIDEO

537 W. Highlands Ranch Pkwy, Ste. 114
Highlands Ranch, CO 80129
720.759.7268


56 Harvester Ave, Ste. 1-201
Batavia, NY 14020
585.591.6590


STEP TEN
Place waterproof roof cover (Z)

and screws 4.0 x 50 (P).
Install front and rear decorative



WILL LOOK HERE.
W
P
P
Z1
W
P
Z