THOMSON CB1000 User manual

CB1000
EN DVD / VIDEO CASSETTE RECORDER
Downloaded From Disc-Player.com Thomson Manuals

2EN
.
Precautions
Laser Safety
This unit employs a laser. Only qualified service personnel
should remove the cover or attempt to service this unit, due to
the possibility of eye injury.
Power Supply
The power supply is connected and the unit is live when the
mains cable is plugged into a 220 - 240 V~, 50 Hz AC outlet.
To operate the unit, press [STANDBY-ON Q].
Caution
1. Do not attempt to open the cabinet. There are no user
serviceable parts inside. Refer all servicing to qualified
service personnel.
2. Slots and openings in the cabinet at the sides and
underneath are provided for ventilation. To ensure reliable
operation and to protect the unit from overheating, these
openings must not be blocked or covered.
Avoid installation in enclosed spaces such as bookcases
unless suitable ventilation is provided.
3. Keep the unit away from radiators and other heat sources.
4. Avoid use near strong magnetic fields.
5. Do not push objects of any kind into the unit through the
cabinet slots or openings as they could touch electrically
live parts or short circuit parts resulting in a fire or electric
shock.
6. To prevent fire or shock hazard, do not expose this
apparatus to dripping or splashing, no objects filled with
liquids, such as vases, should be placed on the
apparatus.
7. Do not stand the unit vertically. Use the unit in a horizontal
(flat) position only.
8. Before attempting to operate the unit, make sure that the
timer recording mode is off.
9. This product is in Stand-by mode when turned off while
the mains cable is connected.
The front panel display will not light up. This is a
Power Saving Mode (ECO) for standby.
10. Do not place any combustible objects on the device
(candles, etc.).
11. Before moving the unit, be sure to remove any discs and
unplug the mains cable from the AC outlet.
12. Disconnect the mains plug to switch off when the unit
becomes faulty or not in use.
13. The mains plug shall remain readily operable.
14. Read the manual instructions to ensure correct and safe
installation and interconnection of the unit in multimedia
systems.
15. Keep the distances 20 cm around apparatus of ventilation
openings.
Introduction
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The important note is located on the rear of the cabinet.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
The symbol for CLASS II (Double Insulation)
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK DEFEATED.
DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
WARNING: LIVE PARTS INSIDE.
DO NOT REMOVE ANY SCREWS.
E9TF0ED_EN.book Page 2 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

3
EN
Introduction ConnectionsBasic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
Make your contribution to the environment!!!
•Exhausted batteries do not belong in the
dustbin.
•You can dispose of them at a collection point for
exhausted batteries or special waste.
•Contact your council for details.
Installation Location
For safety and optimum performance of this unit:
•Install the unit in a horizontal and stable position.
•Keep the unit away from electronic equipment such as an
amplifier, TV, etc. to prevent warping,damage, fire and
malfunction.
•Do not place anything directly on top of the unit.
•Shield the unit from direct sunlight and keep away from
sources of intense heat. Avoid dusty or humid locations.
Avoid locations with insufficient ventilation for suitable heat
dissipation. Do not block the ventilation holes on the sides of
the unit. Avoid locations subject to strong vibration or strong
magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
•Do not handle the mains cable with wet hands.
•Do not pull on the mains cable to disconnect it from the AC
outlet. Grasp it by the plug.
•If, by accident, water is spilled on the unit, unplug the mains
cable immediately and take the unit to an authorised service
centre for servicing.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is
moved from a cold place to a warm place, after heating a cold
room, or under conditions of high humidity. Do not use the unit
for at least 2 hours to allow the inside to dry.
About Copyright
Unauthorised copying, broadcasting, public performance and
lending of discs are prohibited. This product incorporates
copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this
copyright protection technology must be authorised by
Macrovision, and is intended for home and other limited
viewing uses only unless otherwise authorised by
Macrovision. Reverse engineering or disassembly is
prohibited.
Notice for the Progressive Scan Outputs
Consumers should note that not all high definition television
sets are fully compatible with this product and may cause
artifacts to be displayed in the picture. In case of picture
problems with 480 or 576 progressive scan output, it is
recommended that the user switch the connection to the
‘standard definition’ output. If there are questions regarding
your TV set compatibility with this 480p or 576p product,
please contact our customer service centre.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can
be reused. Please dispose of any materials in accordance
with your local recycling regulations.
This product consists of materials which can be recycled
and reused if disassembled by a specialised company.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not
be treated as household waste. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this
product. For more detailed information
about recycling of this product, please
contact your local city office, your
household waste disposal service or the
shop where you purchased the product.
Following information is only valid EU-member States:
Disposal of batteries and/or accumulators
The crossed out wheeled dust bin symbol indicates that
batteries and/or accumulators must be collected and
disposed of separately from household waste.
If the battery
or accumulator contains more than the specified values of
lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in
the Battery Directive (2006/66/EC), then the chemical
symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd)
will appear below the crossed out wheeled dust bin
symbol. By participating in separate collection of batteries,
you will help to assure the proper disposal of products and
batteries and thus help to prevent potential negative
consequences for the environment and
human health. For more detailed
information about the collection and
recycling programmes available in your
country, please contact your local city office
or the shop where you purchased the
product.
Do not place the unit on the furniture that is capable of
being tilted by a child and an adult leaning, pulling,
standing or climbing on it. A falling unit can cause serious
injury or even death.
Pb, Hg, Cd
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
“Dolby®Digital Recording enables consumers to record
high-quality video with stereo sound on recordable DVD
discs. The technology, when utilised instead of PCM
recording, also saves recordable disc space, allowing for
higher video resolution or extended recording time on
each DVD. DVDs created using Dolby Digital Recording
will play back on all DVD-Video players.”
Note: This is true when the players are compatible with
actual recordable DVD discs.
E9TF0ED_EN.book Page 3 Wednesday, March 17, 2010 1:32 PM
This appliance complies with the standards in force for
this type of product.
Downloaded From Disc-Player.com Thomson Manuals

4EN
Maintenance
CLEANING THE UNIT
Use a soft cloth slightly moistened with a mild detergent
solution. Do not use solutions containing alcohol, spirits,
ammonia or abrasives.
CLEANING DISCS
If a disc becomes dirty, clean it with a cleaning cloth. Wipe the
disc from the centre out. Do not wipe in a circular motion.
Do not use solvents such as benzine, thinners, commercially
available cleaners, detergent, abrasive cleaning agents or
antistatic spray intended for analogue records.
DISC HANDLING
Handle the discs so that fingerprints and dust do not adhere
to the disc surfaces.
Always store the disc in its protective case when it is not in
use.
SERVICING
If the unit becomes inoperative, do not try to correct the
problem by yourself. There are no user serviceable parts
inside. Turn the unit off, unplug the mains cable, and consult
your dealer or an authorised service centre.
CLEANING THE DISC LENS
If the unit does not perform correctly even though you have
referred to “Troubleshooting” and the relevant sections in the
Owner’s Manual, the laser optical pickup unit may be dirty.
Consult your dealer or an authorised service centre for
inspection and cleaning of the laser optical pickup unit.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while
the TV programme reception is clear. Dirt accumulated on
the video heads after a long period of use, or the usage of
rental or worn tapes can cause this problem. If a streaky or
snowy picture appears during playback, the video heads in
the unit may need to be cleaned.
1Please visit your local Audio / Video store and purchase a
good quality VHS Video Head Cleaner.
2If a Video Head Cleaner does not solve the problem,
please consult your dealer or an authorised service centre.
Note
• Remember to read the instructions along with the video
head cleaner before use.
• Clean video heads only when problems occur.
Manufactured under license under U.S.
Patent #: 5,451,942 & other U.S. and
worldwide patents issued & pending. DTS
and the Symbol are registered trademarks
and DTS Digital Out and the DTS logos
are trademarks of DTS, Inc. Product
includes software.
© DTS, Inc. All Rights Reserved.
HDMI, the HDMI Logo, and
High-Definition Multimedia
Interface are trademarks or
registered trademarks of HDMI
Licensing LLC in the United
States and other countries.
DivX®, DivX Certified®and associated
logos are registered trademarks of
DivX, Inc. and are used under license.
is trademark of Eastman Kodak Company.
DVB is a registered trademark of the DVB
Project
‘MP3 SURROUND’ and its logo are trademarks of
Thomson S.A.
Note: Supply of this product does not convey a license nor
imply any right to distribute content with this product in
revenue-generating broadcast systems (terrestrial,
satellite, cable and/or other distribution channels),
streaming applications (via Internet, intranets and/or other
networks), other content distribution systems (pay-audio or
audio-on-demand applications and the like) or on physical
media (compact discs, digital versatile discs,
semiconductor chips, hard drives, memory cards and the
like). An independent license for such use is required.
For details, please visit
http://mp3licensing.com.
E9TF0ED_EN.book Page 4 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

5
EN
Introduction Connections Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
• Remote control with 2 R6 (1.5 V) batteries
•RFcable
• Owner’s Manual
•CD-ROM
• Warranty Card
Features
The following features are available with this unit.
• Recording up to 12 programmes
• One-touch timer recording:
• VPS /PDC: [EPage 34]
• Automatic chapter mark setting: [EPage 30]
• Automatic Playlist making
(VR mode DVD-RW discs only)
• Automatic finalising
(video mode DVD-RW/-R discs only): [EPage 41]
• Automatic title menu making
(video mode DVD-RW/-R discs only): [EPage 41]
• DV dubbing:
• Dubbing mode: [EPage 40]
• Theatre surround sound: [EPage 19]
• Quick search: [EPage 50]
•CMskip:[EPage 47]
• Playback from Original or a Playlist
(VR mode DVD-RW discs only): [EPage 42]
• Virtual Surround System: [EPage 53]
• Playing back data files recorded in a USB device:
[EPage 43]
• Chasing playback during recording and simultaneous
playback and recording: [EPage 49]
• Playing back MP3 / JPEG / DivX®/ Kodak Picture CD
files: [EPages 42-46]
• Quick search: [EPages 71-72]
• Adding or deleting chapter marks manually:
[EPages 56-57]
• Creating titles to a Playlist
(VR mode DVD-RW discs only): [EPage 58]
• Deleting titles: [EPage 55]
• Deleting a scene of a title
(VR mode DVD-RW discs only): [EPage 59]
• Editing title name: [EPage 56]
• Combining titles
(VR mode DVD-RW discs only): [EPage 58]
• Dividing titles
(VR mode DVD-RW discs only): [EPages 57-58]
• Protecting titles
(VR mode DVD-RW discs only): [EPage 57]
• Adding or deleting chapter marks at once
(video mode DVD-RW discs only): [EPage 57]
• Playing back discs recorded in video mode in any
regular DVD player: [EPage 41]
• Progressive scan system: [EPages 17, 67]
• HDMI (High-Definition Multimedia Interface):
[EPages 18, 68]
Accessories Supplied
Recording
DVD VCR
(DVD) [EPage 32]
(VCR) [EPage 70]
DVD
Dubbing
DVD VCR
(DVD) [EPages 38-39]
(VCR) [EPage 71]
Playback
DVD
VCR
Editing
DVD
Compatibility
DVD
Others
DVD
E9TF0ED_EN.book Page 5 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

6EN
Table of Contents
Introduction ...................................................... 2
Precautions ........................................................................ 2
Features ............................................................................. 5
Guide to the Owner’s Manual............................................. 7
Functional Overview......................................................... 10
Installing Batteries in the Remote Control ........................ 12
Switching DVD / VCR mode ............................................. 12
Guide to On-Screen Displays........................................... 13
Front Panel Display Guide................................................ 16
Connections ................................................... 17
Connecting to a TV........................................................... 17
Connecting to External Equipment................................... 19
Digital Audio for Better Sound Quality .............................. 19
Basic Setup / TV View Operation .................. 20
Initial Setting..................................................................... 20
Channel Setting................................................................ 21
TV View Operation ........................................................... 23
Recording........................................................ 28
Information on DVD Recording......................................... 28
Formatting a Disc ............................................................. 30
Selecting the Audio Mode ................................................ 31
Basic Recording and One-touch
Timer Recording (OTR) ................................................. 32
Timer Recording............................................................... 33
Timer Recording (EPG).................................................... 36
Satellite Link ..................................................................... 36
Settings for External Equipment....................................... 37
Information on DV Dubbing .............................................. 38
DVC to DVD Dubbing ....................................................... 39
Dubbing Mode .................................................................. 40
Setting a Disc to Protect................................................... 41
Finalising Discs ................................................................ 41
Playback.......................................................... 42
Basic Playback ................................................................. 42
Special Playback .............................................................. 47
Search .............................................................................. 50
Repeat / Random / Programme Playback / Slide Show ... 51
Selecting the Format of Audio and Video......................... 52
Editing ............................................................. 54
Guide to a Title List .......................................................... 54
Editing Discs .................................................................... 55
Function Setup ............................................... 60
General Setting ................................................................ 63
VCR Functions................................................ 70
Playback........................................................................... 70
Basic Recording and One-touch
Timer Recording (OTR) ................................................. 70
Search.............................................................................. 71
Other Operations.............................................................. 72
Changing the Video Colour System................................. 72
Hi-Fi Stereo Sound System ............................................. 72
Others .............................................................. 73
Troubleshooting................................................................ 73
Troubleshooting for Error Messages ................................ 76
Language Code ............................................................... 78
Specifications................................................................... 79
Declaration of Conformity................................... Back Cover
E9TF0ED_EN.book Page 6 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

7
EN
Introduction Connections Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
Guide to the Owner’s Manual
To show what recording mode or media type applies to each
function, the following symbols appear at the beginning of
each operating item.
The following is the description for the symbols for tuner
setting used in this manual.
Symbols Used in the Owner’s Manual
Symbol Description
Available to DVD-videos
Available to DVD-RW discs in video mode
Available to DVD-RW discs in VR mode
Available to DVD-R discs in video mode
Available to audio CDs
Available to CD-RW/-R discs and USB device with
MP3 files
Available to CD-RW/-R discs and USB device with
JPEG files
Available to DVD-RW/-R, CD-RW/-R discs and USB
device with DivX®files
(DivX®files in USB device are not guaranteed.)
Available to VHS tapes
Use only cassettes marked VHS ( )
Symbols for Tuner Setting and
Recording
ANALOG : Settings only for the analogue mode
DVB : Settings only for the DVB mode
“DVB” means “Télévision Numérique
Terrestre” (TNT).
DVD-V
DVD-V
DVD-V
DVD-RW
DVD-RW
DVD-RW
Video
DVD-RW
DVD-RW
DVD-RW
VR
DVD-R
DVD-R
DVD-R
CD
CD
CD
MP3
MP3
MP3
JPEG
JPEG
JPEG
DivX
DivX
®
DivX®
VCR
VCR SECAMPAL
E9TF0ED_EN.book Page 7 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

8EN
DVD players with are capable of playing DVD-RW recorded in VR mode.
Media for Recording / Playing
Media Type DVD-RW DVD-R
Logo
Format Can be formatted in VR or video mode Automatically formatted
in video mode
Video Mode VR Mode
Icon
Maximum Record Time
480 min
(12 cm)
144 min
(8 cm)
480 min
(12 cm)
144 min
(8 cm)
480 min
(12 cm)
144 min
(8 cm)
Recordable/Playable
Versions
1×-6×
Ver. 1.1/1.2
Ver. 1.1/1.2 CPRM compatible
1×-16×
Ver. 2.0/2.1
Compatibility
Playable on most DVD
players.
Finalisation necessary.
(Title menu will be
created)
Playable only on VR
mode compatible unit.
Finalisation
recommended.
Playable on most DVD
players.
Finalisation necessary.
(Title menu will be
created)
Available Features
Recording Features
Record TV
Programmes ✔✔✔
Reuse by Deleting
the Current
Contents
✔✔
Record 16:9 Size
Pictures ✔✔✔
Record Copy-once
Programmes ✔*
Create Chapters at
Fixed Intervals
(auto chapter)
✔✔✔
Editing Features Playlist Original
Scene Delete ✔✔
Edit Title Name ✔✔✔✔
Create Chapters
Wherever You Like
(chapter mark)
✔✔
Divide a Title ✔
Combine Titles ✔
Delete a Title ✔✔✔✔
Create a Playlist ✔
Protect a Title ✔
✔: Available Grey: Not available
* CPRM compatible disc only.
DVD-RW
DVD-RW
DVD-RW
Video
DVD-RW
DVD-RW
DVD-RW
VR
DVD-R
DVD-R
DVD-R
E9TF0ED_EN.book Page 8 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

9
EN
Introduction Connections Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
is a trademark of DVD Format/Logo Licensing Corporation.
• ABOUT DIVX VIDEO: DivX®is a digital video format created
by DivX,Inc. This is an official DivX Certified device that
plays DivX video. Visit www.divx.com for more information
and software tools to convert your files into DivX video.
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play DivX Video-on-
Demand (VOD) content. To generate the registration code,
locate the DivX VOD section in the device setup menu. Go
to vod.divx.com with this code to complete the registration
process and learn more about DivX VOD.
• DivX Certified®to play DivX®video, including premium
content.
• Media containing the DivX®files with the DivX®GMC (Global
Motion Compensation) playback feature, which is DivX®
supplemental function, cannot be played back on this unit.
The following discs will not play back on this unit.
On the following disc, the sound may not be heard.
• Super audio CD - Only the sound on the CD layer can be
heard. The sound on the high-density super audio CD layer
cannot be heard.
This unit uses the PAL system. However, it is also possible to
play back DVDs using other colour systems, such as NTSC.
This unit has been designed to play DVD with
region 2. If these region symbols do not appear on
your DVD, you cannot play back the DVD in this unit.
The number inside the globe refers to region of the
world.
Following discs are recommended for good recording quality
and are proven to be compatible with this unit.
However, depending on the media condition the unit may not
read the disc properly.
Discs for Playing
Disc Type DVD-VIDEO CD-DA CD-RW CD-R
Logo
Icon
Files for Playing
Type of title MP3 JPEG DivX®
Icon
Media CD-RW/-R
USB device
CD-RW/-R
USB device
CD-RW/-R
DVD-RW/-R
USB device (not guaranteed)
DVD-V
DVD-V
DVD-V CD
CD
CD CD
CD
CD CD
CD
CD
MP3
MP3
MP3 JPEG
JPEG
JPEG DivX
DivX
®
DivX®
Unplayable Discs
• CD-ROM • Compact Disc-Interactive
(CD-I)
• Video Single Disc (VSD) • DVD-ROM
• DVD-audio • Unfinalised disc
• DVD or CD contains Windows Media™ Audio files
• DVD-RW/-R recorded in non compatible recording format
•Blu-rayDisc •HDDVD
Colour Systems
Region Codes
Verbatim DVD-R 8x, DVD-RW 2x
JVC DVD-RW 4x
Maxell DVD-R 8x/16x
2
E9TF0ED_EN.book Page 9 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

10 EN
Functional Overview
You can also turn on the unit by pressing these buttons.
You can turn on the unit by pressing these buttons only when a videotape is in this unit.
Press to turn on the unit, or to turn the unit into the standby mode. (To completely shut down the unit, you must unplug the
AC power cord.)
1 STANDBY-ON indicator
2 Cassette compartment
3 OPEN\CLOSE Abutton*1(DVD)
4 VCR/DVD indicators
5 Disc tray
6 DV-IN jack (AV3)
7 USB input jack
8RECORDIbutton (DVD)
9PLAYBbutton*1(DVD)
10 STOP Cbutton (DVD)
11 SELECT button
12 DUBBING button
13 PROG. K\Lbuttons
14 Display (“Off” in standby)
15 Infrared sensor window
16 RECORD Ibutton (VCR)
17 PLAY Bbutton*2(VCR)
18 F.FWD Dbutton*2(VCR)
19 REW Ebutton*2(VCR)
20 STOP\EJECT CAbutton (VCR)
21 STANDBY-ON Qbutton*3
1 Mains cable
2 HDMI OUT jack
3 DIGITAL AUDIO OUT (COAXIAL) jack
4 AUDIO OUT (L\R) jacks
5 COMPONENT VIDEO OUT jacks
6 AV2 (DECODER) socket
7 AV1 (TV) socket
8 ANTENNA IN
9 ANTENNA OUT
Note
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.
• After turning off the unit, leave the mains cable plugged for about one minute. Otherwise it may cause data loss or the unit may
not work properly.
• This unit does not have an RF modulator.
Front Panel
Button names described in the Owner’s Manual
The instructions in this manual are described mainly with the operations using the remote control. Some operations can be
carried out using the buttons on the front panel.
Rear Panel
1 3 456 87 92
E9TF0ED_EN.book Page 10 Wednesday, March 17, 2010 1:32 PM
1
20
19
*2 21 *3
18 *2
16
11 9
*1
2 3*1 54
17 *2
13 12 10 8 7 6
1415
Downloaded From Disc-Player.com Thomson Manuals

11
EN
Introduction ConnectionsBasic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
1 STANDBY-ON Qbutton
2 INPUT SELECT button
3 Number buttons
4 SAT.LINK button
5 TEXT button
6 AUDIO button
7 TOP MENU button (DVD)
8 Direction K/L/0/1buttons
9 DISPLAY button
10 RED/GREEN/YELLOW/BLUE button
SYSTEM (YELLOW) button (VCR)
SEARCH (BLUE) button (VCR)
11 REVEbutton
12 PLAY Bbutton
13 SKIP Hbutton (DVD)
14 VCR button
15 PAUSE Fbutton
16 DUBBING button
17 SETUP button
18 TIMER SET button
19 HDMI button
20 OPEN\CLOSE EJECT Abutton
21 PROG.G \ H buttons
22 TIME SHIFT button (DVD)
23 Cbutton
24 CLEAR button
25 GUIDE button
26 SUBTITLE button
27 MENU/LIST button (DVD)
28 ENTER/OK button
29 RETURN/BACK button
30 FWD Dbutton
31 STOP Cbutton
32 SKIP Gbutton (DVD)
33 DVD button
34 CM SKIP button (DVD)
35 REC SPEED button
36 REC button
37 1.3x/0.8x PLAY button (DVD)
38 TIMER PROG. button
Note
•If you turn off this unit,
•
[OPEN\CLOSE EJECTA]on the
remote control is not available. Be sure to use
[OPEN\CLOSE A] or [STOP\EJECT C A]on the unit.
Remote Control
1
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
37
36
38
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
12
Button names described in the Owner’s Manual :
The instructions in this manual are described mainly with the
operations using the remote control. Some operations can
be carried out using the buttons on the front panel.
E9TF0ED_EN.book Page 11 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

12 EN
Installing Batteries in the Remote
Control
Install 2 R6 (1.5 V) batteries (supplied) into the remote
control, carefully match with the polarity indicated inside the
battery compartment.
Caution
• Incorrect use of batteries can result in hazards such as
leakage and bursting.
• Do not mix new and old batteries together.
• Do not use different kinds of batteries together.
• Make sure that the plus (+) and minus (–) ends of each
battery match the indications inside the battery
compartment.
• Remove batteries if the equipment will not be used for a
month or more.
• When disposing used batteries, please comply with
governmental regulations or the public instructions for
environmental protection that apply in your country or area.
• Do not recharge, short-circuit, heat, burn or disassemble
batteries.
• Make sure there is no obstacle between the remote control
and the remote control sensor on the unit.
• Use within the operating range and angle as shown.
• The maximum operable range as follows:
• Remote control operation may become unreliable if the
remote control sensor of the unit is being exposed by the
strong sunlight or fluorescent light.
• Remote controls for different devices can interfere with each
other. Be careful when using remote controls for other
equipment located close to the unit.
• Replace the batteries when the operating range of the
remote control reduces.
Switching DVD / VCR mode
You must select which component you want to operate first.
Press [DVD] or [VCR] on the remote control or [SELECT] on
the front panel.
Press [DVD] on the remote control or [SELECT] on the front
panel.
(Verify that the DVD indicator is lit in green.)
Press [VCR] on the remote control or [SELECT] on the front
panel.
(Verify that the VCR indicator is lit in orange.)
About the Remote Control
Line of sight: approximately 7 m
Either side of centre: approximately 5 m within 30 degrees
21 3
Within
about 5 m
5 m (30°)7 m
5 m (30°)
DVD
VCR
DVD button
VCR button
button
indicators
E9TF0ED_EN.book Page 12 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

13
EN
Introduction Connections Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
Guide to On-Screen Displays
Press [DVD] first.
With a disc inserted into the unit, press [DISPLAY] to display
the on-screen display. The on-screen display shows
information about what is recorded on the disc.
This is an example screen for explanation. Displayed items
vary depending on the actual mode.
1 Indicates a disc type and format mode.
2 Indicates a type of titles for VR mode DVD-RW
disc.
3 Indicates a channel number, station name
(analogue channel only) or selected external
input mode.
4 Indicates a media, recording speed and
possible recording time left.
5 Indicates the current title number/total number
of titles, the current chapter number/total
number of chapters, and time lapse of the
current title playback/total duration of the title.
6 Each icon means:
7 Indicates an operation status.
8 Indicates the component in use.
: DVD
: USB device
Note
• For some descriptions on this manual, only one disc type is
indicated as an example.
Press [DISPLAY] repeatedly while the display menu is
displayed to display the following information.
1 Indicates the resolution of the HDMI output
image.
2 Indicates the HDMI video format.
3 Indicates the HDMI audio format.
• “- - -” will be displayed, when it does not have any
information.
DISPLAY Menu
DVD
: Search
: Audio
: Subtitle
: Angle
: Repeat
: Marker
: Noise Reduction
: Zoom
: Surround
1/ 5 1/ 5
- RW VR ORG
0:01:00 / 1:23:45
2
2
2
8
8
8
5
5
5
6
6
6 1
1
1
3
7
1 TF1
T C
DVD 2H 1:53
4
<Title / File Name Information>
Title name information
(only when VR mode DVD-RW, unfinalised
video mode DVD-RW/-R disc is in playback)
File name information
(only when MP3/JPEG/DivX®files is in
playback)
<MP3 Tag Information>
(only when MP3 file is in playback)
Title name information
Artist name information
Album name information
<HDMI Information>
(only for the images output through the HDMI
output)
Title Name
My Title
File Name
My File
Title Name
Artist Name
Album Name
480p / YCbCr
1
1
1 2
2
2
3
3
3
Video Info. :
Audio Info. : Bitstream
E9TF0ED_EN.book Page 13 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

14 EN
While in the VCR mode, the on screen display of the VCR
mode is displayed.
Press [VCR] first.
Press [DISPLAY] to display the on screen display.
.
1 Current time
2Positionnumber
3 Audio status of the receiving broadcast or
external equipment
4 Audio status of the currently playing back
videotape
5 Tape counter
6 Recording or playing back speed
7 Status of the current tape
Press [C]while viewing a DVB programme to display the
programme information.
1 Audio language
2 Channel number
3 Channel name
4 Current time and day
5 Next programme information
6 Current programme information
The window will automatically exit after 4 seconds, or press
[RETURN\BACK] to exit.
While the window appears, press [C]again to display more
information. Press [RETURN\BACK] to exit.
VCR
0:00:00 STEREO
AV2
STEREO
12:00
SP
7
11
22
33
44
55
7
66
This is an example screen for explanation.
Displayed items are depending on the actual mode.
INFO Menu
DVB
11:23 – 12:20
11:53 Mon
Stereo AD Sub Entertainment 27 min left
12:20 – 12:25
NOW:
13 Channel 4+1
English
NEXT:
Castle
Burning Questions
2
1
6
5
34
E9TF0ED_EN.book Page 14 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

15
EN
Introduction Connections Basic Setup /
TV View Operation
Playback Editing OthersFunction SetupRecording VCR Functions
Press [SETUP] to display the main menu. Then use [K\L]to
select a menu and press [ENTER\OK] to display the sub
menu.
Press [RETURN\BACK] to return to previous screen.
•Eis displayed when a disc with CD-DA/MP3/JPEG/
Kodak Picture CD is inserted.
•Fis displayed when a USB flash memory with MP3/JPEG
is plugged.
1 Playback: [EPage 64]
2Display:[EPage 66]
3Video:[EPage 66]
4 Recording: [EPages 30-31, 37, 41]
5Clock:[EPage 67]
6Channel:[EPages 21-26]
7DivX:[EPages 45, 68]
8 HDMI: [EPage 68]
9 DVB Setting: [EPage 69]
10 Reset All: [EPage 69]
1 Adult Lock: [EPage 69]
2 Maturity Lock: [EPage 69]
3Language:[EPage 69]
4 About: [EPage 69]
To programme a timer recording. [EPage 33]
To call up the title list. [EPage 54]
1 Format (DVD-RW only): [EPages 30-31]
2 Finalise: [EPage 41]
3 Disc Protect (VR mode DVD-RW disc only):
[EPage 41]
4 Delete All Playlists (VR mode DVD-RW disc
only): [EPage 58]
Audio CD
1RandomPlay:[EPage 51]
2 Programme Play: [EPage 51]
CD-RW/-R with MP3 / JPEG / Kodak Picture CD files
3 Music (MP3 files): [EPage 51]
4 Photo (JPEG files): [EPages 51, 52]
5 Slide Show (JPEG/Kodak Picture CD files):
[EPage 52]
1 Music (MP3 files): [EPage 51]
2 Photo (JPEG files): [EPages 51, 52]
Main Menu
AGeneral Setting
DVB Setting
1
1
2
2
3
3
4
4
5
5
A
B
C
D
E
6
6
F
Setup
Timer Programming
Title List
DVD Menu
General Setting
DISC Playback Mode
USB Playback Mode
1
2
3
4
5
6
7
8
9
10
HDMI
DVB Setting
General Setting
Playback
Display
Video
Recording
Clock
Channel
DivX
Parental Lock
Audio Out
Disc Menu Language
Audio Language
Subtitle Language
Angle Icon
Still Mode
TV System
Reset All
Playback
Display
Video
Recording
Clock
Channel
DivX
HDMI
DVB Setting
Adult Lock
Maturity Lock
Language
General Setting
About
Reset All
1
2
3
4
BTimer Programming
CTitle List
DDVD Menu
EDISC Playback Mode
FUSB Playback Mode
1
2
3
4
Format
Finalise
Disc Protect OFF ON
Delete All Playlists
DVD Menu
1
2
DISC Playback Mode
Random Play
Programme Play
DISC Playback Mode
Music
Photo Random Play
Slide Show
3
4
1
5
USB Playback Mode
Music
Photo Random Play
Slide Show
2
1
E9TF0ED_EN.book Page 15 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

16 EN
Front Panel Display Guide
1 DTV indicator
2 Title / Track and Chapter number
3 Current status of the unit
4 Displays the following
• Playing back time
• Current title / chapter / track / file number
• Recording time / remaining time
•Clock
• Channel number
• One-touch Timer Recording (OTR) remaining time
• Selected HDMI video resolution
Note
• Except when satellite recording is in standby, front panel
display stays off while the power is off/timer-standby mode.
This is a new Power Save (ECO) feature.
The disc tray is opening.
The disc tray is closing.
A disc is loading.
Data is being recorded on a
disc.
Appears when the satellite
link recording is in standby.
Appears when HDMI video
resolution (480p) is
selected.
Appears when HDMI video
resolution (576p) is
selected.
Appears when HDMI video
resolution (720p) is
selected.
Appears when HDMI video
resolution (1080i) is
selected.
Appears when HDMI video
resolution (1080p) is
selected.
DB
DTV
DVD
VCR
4
3
2
1
:Appears when the channel is in digital mode.
:Title / track number
:Chapter number
F:Appears when playback is paused.
Appears during step by step playback.
B:Appears when playing back a disc.
FB:Appears during slow forward / reverse playback.
:Appears when the timer programming or One-
touch Timer Recording (OTR) is set and operating.
Appears when the unit goes into the satellite link
standby or recording mode.
Flashes when timer programming and satellite
recording was not executed because of some
error.
I:Appears during recording.
Flashes when recording being paused.
:Appears when a videotape is in this unit.
:Appears when a disc is in this unit.
:Appears during dubbing.
:Appears when this unit is in DVD output mode, or
the timer-standby mode for DVD recording.
:Appears when this unit is in VCR output mode, or
the timer-standby mode for VCR recording.
DB
DVD
V
CR
Display Messages
DVD
DVD
DVD
DVD
DVD
DVD
DVD
DVD
DVD
DVD
E9TF0ED_EN.book Page 16 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

17
EN
Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions
Basic Setup /
TV View Operation
Connecting to a TV
Connect the unit to a TV after considering the capabilities of
your existing equipment.
Connect the antenna or cable to the ANTENNA
IN jack of this unit.
Connect the ANTENNA OUT jack of this unit to
the Aerial jack of your TV.
Connect AV1 (TV) Scart socket of this unit to
the Scart socket of your TV.
Note
• If your TV does not have a Scart socket, use a Scart/RCA
cable to connect.
• Connect this unit directly to the TV. If the AV cables are
connected to a VCR, pictures may be distorted due to the
copy protection system.
• Analogue teletext can only be output in VCR mode through
AV1 (TV) out. Use TV remote control to decode the
analogue teletext.
• When changing the “Video Out” setting (“SCART (RGB)”,
“Component (Interlace)” or “Component (Progressive)”),
connect to the corresponding jack on the TV. If the setting is
changed, for example, to “Component (Interlace)” or
“Component (Progressive)” while the scart cable is
connected to the TV, a distorted video signal may be output.
If your TV has component video input jacks, use a component
video cable (to connect the COMPONENT VIDEO OUT jacks)
and an audio cable (to connect the AUDIO OUT (L/R) jacks).
When using this type of connection, “Video Out” setting
should be set to “Component (Progressive)” or “Component
(Interlace)”. Refer to “BVideo Out (Default: SCART (RGB))”
on page 67.
• Component connection provides the better quality picture.
Connect the COMPONENT VIDEO OUT jacks of
this unit to the component video input jacks of
your TV.
Connect the AUDIO OUT (L\R) jacks of this unit
to the analogue audio input jacks of your TV.
• After you have made the connections, set the “Video Out”
setting. (See page 67.)
Selecting Progressive Scan (576p/480p or
Interlaced 576i/480i) Playback
• If your TV is compatible with progressive scanning (576p/
480p), connect the TV to the COMPONENT VIDEO OUT
jacks of this unit and set “Video Out” setting to “Component
(Progressive)” in “Setup” menu. (See page 67.) Next, set
your TV to the progressive scan mode.
• If your TV is not compatible with progressive scan, set
“Video Out” setting to “Component (Interlace)”.
• Use a commercially available adaptor if the video input jacks
of your TVs or monitors are the BNC type.
• Only component and HDMI connections are compatible with
the Progressive Scan.
Connections
Before installation, unplug your TV and
this unit
Using the Scart socket
1
2
RF cable
(not supplied)
RF cable
(supplied)
Cable
Signal
or
To A e r i a l j a c k
Antenna
1
2
Scart cable
(not supplied)
Scart/RCA cable (not supplied)
Audio/video cable
(not supplied)
Scart adaptor
(not supplied)
Using the COMPONENT VIDEO OUT
Jacks and the AUDIO OUT (L\R) Jacks
YPB/CBPR/CR
1
2
Audio IN Component
video IN
Audio cable
(not supplied)
Component
video cable
(not supplied)
1
2
E9TF0ED_EN.book Page 17 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

18 EN
[HDMI CONNECTION]
• HDMI outputs the video / audio signals without converting to
analogue signals.
• No audio connections is required.
• Use the HDMI cable (commercially available) for connection.
• Connect the HDMI output jack of this unit to the HDMI input
jack of TV.
Selecting HDMI video resolution
Press [HDMI] to select the HDMI video resolution. The video
resolution changes as follows every time [HDMI] is pressed.
576p (PAL) / 480p (NTSC) J720p J1080i J1080p
(An HDMI video resolution that is not supported by the display
device will be skipped.)
For audio CD and MP3 files, 2 channel PCM will be output
regardless of the “Dolby Digital” setting.
If the connected device is not compatible with HDMI
BITSTREAM, audio will be output as PCM even if you select
“Stream” in “Dolby Digital” setting. (See page 65.)
Copyright protection system
To play back the digital video images of a DVD via an HDMI
connection, it is necessary that both the player and the display
device (or an AV amplifier) support a copyright protection
system called HDCP (high-bandwidth digital content
protection system). HDCP is copy protection technology that
comprises data encryption and authentication of the
connected AV device. This unit supports HDCP. Please read
the operating instructions of your display device (or AV
amplifier) for more information.
* HDMI: High Definition Multimedia Interface
Note
• Because HDMI is an evolving technology, it is possible that
some devices with an HDMI input may not operate properly
with this unit.
• When using an HDCP-incompatible display device, the
image will not be viewed properly.
• Among the devices that support HDMI, some devices can
control other devices via the HDMI connector; however, this
unit cannot be controlled by another device via the HDMI
connector.
• The audio signals from the HDMI connector (including the
sampling frequency, the number of channels and bit length)
may be limited by the device that is connected.
• Among the monitors that support HDMI, some do not
support audio output (for example, projectors). In
connections with device such as this unit, audio signals are
not output from the HDMI output connector.
• When this unit’s HDMI connector is connected to a DVI-D
compatible monitor (HDCP compatible) with an HDMI-DVI
conversion cable, the signals are output in digital RGB.
• If the connected equipment is not compatible with HDMI
BITSTREAM, DTS sound will not be output.
• When the power failure occurs, or when you unplug the unit,
some problems in the HDMI setting might occur.
Please check and set the HDMI setting again.
Using an HDMI Compatible Port
Actual Output Modes by Media
Audio recording format of
the disc
Dolby Digital / DTS /
MPEG setting of this
unit
Actual output
DVD-video
Dolby
Digital
PCM 2 channel PCM
Stream Dolby Digital
LPCM PCM 2 channel PCM
Stream
DTS®ON DTS®
OFF -
MPEG PCM 2 channel PCM
Stream MPEG
DivX®
Dolby
Digital
PCM 2 channel PCM
Stream Dolby Digital
MP3 PCM 2 channel PCM
Stream
MP2 PCM 2 channel PCM
Stream MPEG
HDMI IN
TV
To HDMI
input jack
this unit
HDMI cable (not supplied)
E9TF0ED_EN.book Page 18 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

19
EN
Introduction Connections Playback Editing OthersFunction SetupRecording VCR Functions
Basic Setup /
TV View Operation
Connecting to External Equipment
This unit has three input terminals. Press [INPUT SELECT]
repeatedly to select the external input mode, then press
[PROG. G\H]repeatedly to select AV1, AV2 or DV(AV3).
Be sure that all the units are switched off before making
connections.
Note
• When you record a TV programme from a Satellite Box /
decoder, you must connect a Scart cable to AV2 (DECODER).
(See page 36.)
• The signal from the external device will be output
automatically when the TV is connected to AV1 and the
external device is connected to AV2 using a Scart cable with
its power on. (However, it will not be output when this unit’s
power is turned off.)
If you want to monitor this unit’s signal, press [DISPLAY]
or turn the external device off. (The signal from this unit can
only be monitored during playback.)
If you want to monitor the signal from other input, press
[DISPLAY], then press [INPUT SELECT] to select the
desired external input mode, then select the desired input
channel using [PROG. G\H].
When connecting a DV-camcorder, use DV-IN jack of DV(AV3)
(Front).
Digital Audio for Better Sound Quality
For clear digital sound quality, use the DIGITAL
AUDIO OUT (COAXIAL) jack to connect your digital
audio equipment.
If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
• Connecting multi-channel Dolby Digital decoder allows you
to enjoy the Multi-channel Dolby Digital surround system as
well as DTS decoder, Multi-channel surround system.
• After connecting to a Dolby Digital decoder, set “Dolby
Digital” to “Stream” in “Audio Out” menu. (See pages 64-65.)
• After connecting to a DTS decoder, set “DTS” to “ON” in
“Audio Out” menu. (See pages 64-65.)
• After connecting to a MPEG decoder, set “MPEG” to
“Stream” in “Audio Out” menu. (See pages 64-65.)
• The audio source recorded in Dolby Digital Multi-channel
surround format cannot be recorded using an MD or DAT
deck as a digital sound.
• If not connected to a Dolby Digital decoder, set “Dolby
Digital” to “PCM” in “Audio Out” menu. Playing back a DVD
using incorrect settings may generate noise distortion and
damage speakers.
• Set “Dolby Digital” and “MPEG” to “PCM” and set “DTS” to
“OFF” in “Audio Out” menu for connecting to an MD or DAT
deck.
• You can use AUDIO OUT (L\R) jacks for the connection of
your audio system.
Recording from a DVD player, Satellite
Box or other Audio-Video equipment
with a Scart output socket (AV2)
Recording from a DV-camcorder
(DV(AV3))
AV output jack
(Scart)
Scart cable (not supplied)
AV2 (DECODER)
DV(AV3) (Front)
DV cable
(4-pin)
(not supplied)
DV OUT
The connections illustrated above are
optional for better sound
Connecting a Dolby Digital™ decoder,
DTS decoder or MPEG decoder
Connecting to an MD deck or DAT deck
COAXIAL
COAXIAL
Dolby Digital decoder,
DTS decoder or
MPEG decoder, etc.
Digital audio
input jack
Coaxial cable
(not supplied)
E9TF0ED_EN.book Page 19 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals

20 EN
Initial Setting
When you turn on this unit for the first time, you need to follow
these steps.
1Press [STANDBY-ON Q].
2Turn the TV on. Select the input to which the
unit is connected.
“Initial Setting” will automatically appear.
3Select your desired language for the OSD using
[K\L]. Then press [ENTER\OK] to go to the
next step.
4Select your desired country for receiving your
local channels properly using [K\L]. Then
press [ENTER\OK] to go to the next step.
This setting is mainly for digital channels.
Digital channels cannot be received properly for the
countries not listed above.
In such case, select “Other”.
5Select your desired tuning type according to
your area using [K\L], then press
[ENTER\OK].
The unit will start getting channels available in your area.
Digital tuning:
Only the DVB channels receivable in your area are
automatically scanned and memorised.
Digital & Analog tuning:
Both analogue and DVB channels receivable in your area
are scanned and memorised automatically.
Analog tuning:
Only the analogue channels receivable in your area are
automatically scanned and memorised.
• If no channel has been memorised, the antenna
confirmation display will appear. Press [ENTER\OK] to start
auto scanning again or press [RETURN\BACK] to cancel
the initial settings.
6After finishing channel setting, “Clock Setting”
will appear.
• The current date and time will appear automatically.
•
If the current date and time are correct, press
[RETURN\BACK] to exit, if they are incorrect, press
[ENTER\OK] and follow to “ A Clock Setting” on
page 67
.
Note
• After “Initial Setting”, if you need to unplug the mains cable,
make sure to turn off the power first and leave it in standby
mode for at least 1 minute before attempting to unplug.
Otherwise, it may cause data loss.
If you want to set each item of “Initial Setting” again, you can
set them at “General Setting”.
• Refer to “AOSD Language (Default: English)” on page 66.
• Refer to “Country Setting” on page 23.
• Refer to “Auto Tuning (DVB & ANALOG)” on page 21.
• Refer to “Auto Tuning (ANALOG)” on page 21.
• Refer to “Auto Tuning (DVB)” on pages 22-23.
• Refer to “Clock” on page 67.
Also you can customize the memorised channel at “General
Setting”.
Refer to following pages for details.
• Refer to “Manual Tuning (ANALOG)” on pages 21-22.
• Refer to “Manual Tuning (DVB)” on page 23.
• Refer to “Skip a Preset Channel” on page 22.
• Refer to “Move” on page 22.
Use this feature to adjust the aspect ratio of the video source
which is different from your TV’s ratio to fit your TV monitor
without distorting the picture.
1In stop mode, press [SETUP]. Select “General
Setting” using [K\L], then press [ENTER\OK].
2Select “Video” using [K\L], then press
[ENTER\OK].
3Select “TV Aspect” using [K\L], then press
[ENTER\OK].
4Select the desired option using [K\L], then
press [ENTER\OK].
5Press [SETUP] to exit.
Basic Setup / TV View Operation
OSD Language
English
Áúëãàðñêè
Èesky
Français
Deutsch
Magyar
Country
France
Spain - Peninsula
Spain - Canary Islands
Germany
Italy
Switzerland
Czech Republic
Other
Auto Tuning
Make sure the antenna is
connected to “ANTENNA IN” jack.
Digital tuning
Digital & Analog tuning
Analog tuning
Selecting the TV Aspect Ratio
0 : 00
01 / 01 / 2010 (FRI)
Clock Setting
TV Aspect
Video Out
TV Aspect
4:3 Letter Box
4:3 Pan & Scan
16:9 Wide
E9TF0ED_EN.book Page 20 Wednesday, March 17, 2010 1:32 PM
Downloaded From Disc-Player.com Thomson Manuals