THUNDER TIGER TOMAHAWK VX User manual

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20
Tire/Wheels輪胎及輪轂
STEP21
Body Shell車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8
Steering Bellcrank轉向曲柄組
STEP6
Rear Suspension後擺臂懸吊組
STEP6
Rear Suspension後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7
Shock Absorber避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays actual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧依序放入離合器本體，將固定螺絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7
Shock Absorber避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
Marked "S-ST"
標示"S-ST"
Marked "S-ST"
標示"S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTEDXANAVI GT-R R34
CLEARXANAVI GT-R R34W/DECAL
XANAVI GT-R R34DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20),M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20),M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4),5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART#DESCRIPTIONNOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂,26mm(電鍍紅)
10爪輪轂,26mm(黑)
8爪輪轂,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲, M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲(20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20),M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4),5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板
PD9144 CFRP FRONT SHOCK TOWER
碳纖維前避震器支架
PD9145 CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板
PD9148 CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3)
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃(適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160SHOCK SPRING,RED
避震器彈簧,紅(中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑(特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白(特軟)
TOMAHAWK VX OPTION PART LIST
33
PART#DESCRIPTIONNOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示"S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm
2mm
4mm
6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE雙色電鍍藍, 26mm
PD6601-P C/PURPLE雙色電鍍紫, 26mm
PD6601-Y C/YELLOW雙色電鍍黃, 26mm
SPRINT DRIFT TIRE疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART#DESCRIPTIONNOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mmHARD 2.5x1.9mmEXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME電鍍銀, 26mm
PD6682 WHITE白色 , 26mm
PD6682-B BLACK黑色 , 26mm
RACING DISH WHEEL蝶式輪轂
PD7649 WHITE白色, 26mm
PD7650 WHITE白色, 30mm
10爪輪轂
PD7699 WHITE白色, 26mm
PD7770 WHITE白色, 30mm
(2)
WHEEL & TIRE OPTIONPART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803
AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2)(2)(2)(2)
Insert Foam Included.
PD7714OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8
Steering Bellcrank轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7
Shock Absorber避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays actual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧依序放入離合器本體，將固定螺絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7
Shock Absorber避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間距，減少共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
Marked "S-ST"
標示"S-ST"
Marked "S-ST"
標示"S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板
PD9144 CFRP FRONT SHOCK TOWER
碳纖維前避震器支架
PD9145 CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板
PD9148 CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3)
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃(適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160SHOCK SPRING,RED
避震器彈簧,紅(中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑(特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白(特軟)
TOMAHAWK VX OPTION PART LIST
33
PART#DESCRIPTIONNOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm
2mm
4mm
6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE雙色電鍍藍, 26mm
PD6601-P C/PURPLE雙色電鍍紫, 26mm
PD6601-Y C/YELLOW雙色電鍍黃, 26mm
SPRINT DRIFT TIRE疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART#DESCRIPTIONNOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mmHARD 2.5x1.9mmEXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME電鍍銀, 26mm
PD6682 WHITE白色 , 26mm
PD6682-B BLACK黑色 , 26mm
RACING DISH WHEEL蝶式輪轂
PD7649 WHITE白色, 26mm
PD7650 WHITE白色, 30mm
10爪輪轂
PD7699 WHITE白色, 26mm
PD7770 WHITE白色, 30mm
(2)
WHEEL & TIRE OPTIONPART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803
AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2)(2)(2)(2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
STEP4 Front Suspension 前擺臂懸吊組
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
4
3
2
1
1
4
3
2
4
1
3
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8
Steering Bellcrank轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
oil
C.A
x2
LR
12
3
Hint
組裝提示
12
x
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays actual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
A
B
CC
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧依序放入離合器本體，將固定螺絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
Marked "S-ST"
標示"S-ST"
Marked "S-ST"
標示"S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART#DESCRIPTIONNOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE雙色電鍍藍, 26mm
PD6601-P C/PURPLE雙色電鍍紫, 26mm
PD6601-Y C/YELLOW雙色電鍍黃, 26mm
SPRINT DRIFT TIRE疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART#DESCRIPTIONNOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME電鍍銀, 26mm
PD6682 WHITE白色 , 26mm
PD6682-B BLACK黑色 , 26mm
RACING DISH WHEEL蝶式輪轂
PD7649 WHITE白色, 26mm
PD7650 WHITE白色, 30mm
10爪輪轂
PD7699 WHITE白色, 26mm
PD7770 WHITE白色, 30mm
(2)
WHEEL & TIRE OPTIONPART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2)(2)(2)(2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧依序放入離合器本體，將固定螺絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
12
3
12
3
6
5
4
3
2
1
1
1
1
1
2
2
33
4
4
55
6
x2
x2
x
x
3
2
1
5 5
4
3
2
1
3
2
1
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
3
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示"S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME電鍍銀, 26mm
PD6682 WHITE白色 , 26mm
PD6682-B BLACK黑色 , 26mm
RACING DISH WHEEL蝶式輪轂
PD7649 WHITE白色, 26mm
PD7650 WHITE白色, 30mm
10爪輪轂
PD7699 WHITE白色, 26mm
PD7770 WHITE白色, 30mm
(2)
WHEEL & TIRE OPTIONPART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2)(2)(2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧 依序放入離合器 本體，將固定螺 絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
12
3
3
2
1
5
4
12
3
1
1
2
2
3
3
4
4
4
5
3
2
1
4
3
2
1
11
11
2
3
4
3
4
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示 "S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE 脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME 電鍍銀, 26mm
PD6682 WHITE 白色 , 26mm
PD6682-B BLACK 黑色 , 26mm
RACING DISH WHEEL 蝶式輪轂
PD7649 WHITE 白色 , 26mm
PD7650 WHITE 白色 , 30mm
10爪輪轂
PD7699 WHITE 白色, 26mm
PD7770 WHITE 白色, 30mm
(2)
WHEEL & TIRE OPTION PART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2) (2) (2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧 依序放入離合器 本體，將固定螺 絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
x2
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
6
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
3
2
1
5
4
3
2
1
1
2
4
5
54
5
5
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
x2
3
2
1
3
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
6
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示 "S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
1
1
2
2
3
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
6
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE 脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME 電鍍銀, 26mm
PD6682 WHITE 白色 , 26mm
PD6682-B BLACK 黑色 , 26mm
RACING DISH WHEEL 蝶式輪轂
PD7649 WHITE 白色 , 26mm
PD7650 WHITE 白色 , 30mm
10爪輪轂
PD7699 WHITE 白色, 26mm
PD7770 WHITE 白色, 30mm
(2)
WHEEL & TIRE OPTION PART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2) (2) (2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧 依序放入離合器 本體，將固定螺 絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉 LR
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
4
3
2
1
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
2
1
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
LR
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
1
2
11
1
2
1
4
3
2
4
1
3
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示 "S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE 脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME 電鍍銀, 26mm
PD6682 WHITE 白色 , 26mm
PD6682-B BLACK 黑色 , 26mm
RACING DISH WHEEL 蝶式輪轂
PD7649 WHITE 白色 , 26mm
PD7650 WHITE 白色 , 30mm
10爪輪轂
PD7699 WHITE 白色, 26mm
PD7770 WHITE 白色, 30mm
(2)
WHEEL & TIRE OPTION PART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2) (2) (2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧 依序放入離合器 本體，將固定螺 絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
LR
〈For Right〉
〈右側組件〉
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
3
2
1
Marked "S-CM"
標示 "S-CM"
2
1
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
LR
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
3
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
1
2
3
3
2
1
1
2
2
2
3
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示 "S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE 脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assemble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME 電鍍銀, 26mm
PD6682 WHITE 白色 , 26mm
PD6682-B BLACK 黑色 , 26mm
RACING DISH WHEEL 蝶式輪轂
PD7649 WHITE 白色 , 26mm
PD7650 WHITE 白色 , 30mm
10爪輪轂
PD7699 WHITE 白色, 26mm
PD7770 WHITE 白色, 30mm
(2)
WHEEL & TIRE OPTION PART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2) (2) (2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction 前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧 依序放入離合器 本體，將固定螺 絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞 入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
LR
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
3
2
1
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
LR
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
4
2
2
1
Hint
組裝提示
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
1
2
1
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示 "S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
2
2
2
1
13
3
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
2
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE 脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assem ble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME 電鍍銀, 26mm
PD6682 WHITE 白色 , 26mm
PD6682-B BLACK 黑色 , 26mm
RACING DISH WHEEL 蝶式輪轂
PD7649 WHITE 白色 , 26mm
PD7650 WHITE 白色 , 30mm
10爪輪轂
PD7699 WHITE 白色, 26mm
PD7770 WHITE 白色, 30mm
(2)
WHEEL & TIRE OPTION PART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
〈Rear Body Post〉
〈後車殼之註〉
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2) (2) (2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST

How to read the instruction manual?
Temporarily tighten
暫時鎖附暫時鎖附
True-to-scale diagram
實際尺寸對照
Must be purchased separately
改裝品需另購
Apply C.A Glue
使用快乾膠黏合
Apply silicon oil
使用模型專用矽油
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble in right order
依標示順序組裝
Drill holes with the specified diameter
依標示尺寸鑽孔
Cut off shaded portion
依標示部分裁切
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Apply threadlocker
使用螺絲防鬆膠
Assemble in right order
標示依順序組裝
Assemble as many times as specified
依指示組裝所需數量
Must be purchased separately
改裝品需另購
silicon oil
矽油
Assemble in right order
標示依順序組裝
Pay close attention here
注意組裝步驟
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Assemble left and right side the same way
左右側組件相同
Pay close attention here
注意組裝步驟
Ensure smooth, non-binding movement when assembling
確認組件靈活度
Apply threadlocker
使用螺絲防鬆膠
Assemble left and right side the same way
左右側組件相同
Assemble as many times as specified
依指示組裝所需數量
Apply silicon oil
使用模型專用矽油
Apply threadlocker
使用螺絲防鬆膠
Pay close attention here
注意組裝步驟
Apply C.A Glue
使用快乾膠黏合
Assemble as many times as specified
依指示組裝所需數量
Drill holes with the specified diameter
依標示尺寸鑽孔
Pay close attention here
注意組裝步驟
Pay close attention here
注意組裝步驟
Cut off excess
裁剪多餘部分
Pay close attention here
注意組裝步驟
Must be purchased separately
改裝品需另購
Pay close attention here
注意組裝步驟
6mm
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
In the chassis set, these dog bones have been assembled in one-piece unit.
原廠已組配完成
Marked "L"
標示 "L"
4
2
4
4
Apply grease
使用潤滑油膏(黃油)
STEP20 Tire/Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20
STEP16 Engine Set 引擎與離合器罩
STEP16 Installation of Engine Set引擎安裝
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP12 Installation of Rear Brace 結合後補強版
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box結合電池盒
STEP10 Radio Box 電池盒
STEP10 Radio Box 電池盒
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP8 Steering Bellcrank 轉向曲柄組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP6 Rear Suspension 後擺臂懸吊組
STEP5 Rear Differential Unit後差速箱
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
STEP2 2-Speed Transmission Unit 2段變速組
1
24 25 26 27 29
PART# DESCRIPTION NOTE
TOMAHAWK VX PARTS LIST
PD7712
PD8088-1
PD8093
PD8098
PD9051
PD9052
PD9053
PD9054
PD9055
PD9057
PD9058
PD9059
PD9060
PD9061
PD9062
PD9063
PD9064
PD9065
PD9066
PD9067
PD9068
PD9069
PD9070
PD9071
PD9072
PD9073
PD9074
PD9075
PD9076
PD9077
PD9078
PD9079
PD9080
PD9081
PD9082
PD9083
PD9084
PD9085
PD9086
PD9087
PD9088
PD9089
PD9090
PD9091
PD9092
PD9093
PD9094
PD9095
PD9096
PD9097
PD9098
PD9099
PD9100
PD9101
PD9102
PD9103
PD9104
PD9105
PD9106
PD9107
TOMAHAWK VX PART LIST
JD7045 V3
TOMAHAWK VX PART LIST TOMAHAWK VX PART LIST
TOMAHAWK VX PART LIST
2 3
4 5
6 7 8
9
22
2120
19
1817
16151413
23
ANTENNA BAG,BLACK
SHOCK CAP
SHOCK BLADDER
SHOCK PISTON SET
DIFFERENTIAL CASE
FRONT BULK SET
REAR BULK SET
OUTDRIVE CUP SET
DIFFERENTIAL GEAR SET
DRIVE PINION SET 13T
DIFF SPUR GEAR 34T
ONE WAY BEARING SET
1ST/2ND SPUR GEAR,43/38
2 SPD. CLUTCH HUB
2 SPD. CLUTCH SET
2 SPD. DRIVE SHAFT
CTR DIFF. COVER
CTR DIFF. MOUNT
DISC BRAKE SET
2 SPD. CLUTCH BELL
FLY WHEEL
1ST/2ND PINION ,17/22 GEAR
CLUTCH SHOE SET
ENGINE MOUNT
BUMPER SET
URETHANE BUMPER
SHOCK TOWER SET
FRONT SUSP. ARMS
REAR SUSP. ARMS
STEERING BLOCK SET
CASTER BLOCK SET
FRONT UNIVERSAL SHAFT
OUTER HINGE PIN SET
UPPER LINK SET
SUSP. ARM MOUNT BUSHING
INNER HINGE PIN SET
FRONT TOE PLATE,0
REAR TOE PLATE,2.5
SWING RACK SET
SWING POST SCREW
CTR. DRIVE SHAFT SET
CHASSIS BRACE SET
HUB CARRIER SET
SWITCH PLATE & SPACERS
RADIO TRAY
CHASSIS
REAR UNIVERSAL SHAFT
FUEL TANK
MUFFLER
SILICONE TUBING
MANIFOLD
SHOCK SET
SHOCK SPRING,(2.5x1.8mm),BLUE
SHOCK SHAFT
SHOCK CAP & SPRING COLLAR
SHOCK EYELET
BALL STUD,L
BALL STUD,S
TH/BK LINKAGE SET
STEERING SERVO HORN SET
Maintenance Manual & Parts Catalogue
The contents are subject to change without prior notice due to product improvements and specificatrion changes.
Introduction
前言
Thank you for purchasing this Thunder Tiger product. This manual contains the steps and instructions required to assemble
your car. Please read this manual completely before attempting to start maintenance. Follow the directions in this manual closely
to reduce problems during operation. We offer online help on our www.acehobby.com or www.thundertiger.com and forums
and our product specialists are ready to take your call if you have any technical questions. Have fun and enjoy the exciting world
of R/C.
感謝您購買雷虎科技TOMAHAWK VX引擎四驅房車。雷虎科技一向以提供最高品質的產品及服務作為持續努力的目標，並藉由參與競賽及重覆測
試產品，不斷累積經驗，進而提昇設計及製造品質，期望能呈現給您最頂級之工藝產品。本使用說明書包含了組裝及維修本產品前所需注意的重
要事項，建議您在開始組裝及維修本產品之前，能詳閱此說明書，並熟悉本產品之組裝步驟及維修程序。若是您在產品的使用上有任何的疑問，
歡迎多加利用我們所提供的24小時諮詢留言版或洽詢雷虎科技授權經銷商。雷虎科技的全球英文網址為www.thundertiger.com中文網址為www.
tiger.com.tw，我們將竭誠為您服務！
Under Safety Precautions 安全注意事項
Please read all of the instructions and familiarize yourself with the product and its controls before operation.
1. This product is not a toy. It is a high performance model car therefore it is important to familiarize yourself with the model,
its manual, and its construction before assembly or operation. Adult supervision is necessary for children operating this
model.
2. Always keep this instruction manual on hand during assembly and for operating reference.
3. Do not use a power screwdriver to install screws into plastic parts. A power screwdriver’s high rotation speed can heat
up the screw being installed which can result in some melting of the plastic parts or stripped threads.
4. For best performance, it is important to make sure all the moving parts can move freely without binding.
5. This product, its parts, and its assembly tools can be harmful to your health. Always exercise extreme caution when
assembling and operating this product. Keep away from any high speed rotating parts during operation.
感謝您購買雷虎科技產品，在您開始操作本產品前，請詳閱本產品說明書。
1.
本產品為高性能模型產品非一般玩具，組裝與操作過程皆須由成人陪同。請詳讀此本使用說明書，避免因組裝錯誤與操作不當造成損壞。
2.
請妥善保管此說明書，對於後續維修、操控說明將可提供您協助。
3. 請勿使用電動工具旋緊自攻螺絲於塑膠零件上，可能導致塑膠零件融化或滑牙。
4.
請檢視所有活動部位零件是否不受干涉，可靈活作動，以達到車輛最佳性能。
5.
此項產品具有相當之危險性，於組裝、調整、操控上的不熟悉都可能造成自身或他人的傷害，當發生這些傷害事件時製造商是可以免除責
任的，建議您於初次使用本產品前，先行請教具有相當程度經驗同好或是專業雷虎經銷商與模型專賣店。
Index 索引
Manual Format
Tools Included 內附工具
Hex Wrenches
1.5 / 2.0 / 2.5 / 3.0mm
六角板手組
4-Way Cross Wrench
十字套筒
Tools Required For Assembly組裝維修工具
Philips Screwdrivers
(L/M/S)
十字起子
Needle Nose Pliers
尖嘴鉗 Hobby Knife
模型用切割刀
Wire Cutter
斜口剪
Lexan Body Curved Scissor
車殼專用剪
Ruler
尺
Super Glue
(CA Glue)
快乾膠
Grease
潤滑油膏（黃油）
Thread Locking Adhesive
(Threadlocker)
螺絲防鬆膠
Example 說明範例
Symbols Used Throughout The Manual
Hint
組裝提示
12
28
30 31
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
3x25mm
BT Philip Machine Screw
圓頭十字螺絲
Brake Cam
煞車凸輪
Brake Pad
煞車夾片
Brake Screw
煞車夾片固定螺絲
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
2.5mm
E-Clip2
E型扣環
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
2.9x1.8mm
O-Ring
O型環
5x11x4mm
Ball Bearing
軸承
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
STEP4 Front Suspension 前擺臂懸吊組
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
10x15x4mm
Ball Bearing
軸承
3x12mm
BT Machine Screw
圓頭十字螺絲
Caster Block Bushing
C型輪座
STEP4 Front Suspension 前擺臂懸吊組
6mm(L)
Ball Stud
球頭座
2x4mm
BT Self-Tapping Screw
圓頭十字墊圈螺絲
2.5x20mm
Outer Hinge Pin (Front)
輪座固定軸
Shock Shaft
避震器軸
Shock Eyelet
避震軸球頭
2.5mm
E-Clips
E字扣
3x12mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud
球頭座
6mm(S)
Ball Stud
球頭座
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Inner Hinge Pin
擺臂軸
3x10mm
BT Philip Machine Screw
圓頭十字螺絲
6mm(L)
Ball Stud (PD9104)
球頭座
2.5x22mm
Outer Hinge Pin (Rear)
擺臂軸
2x4mm
BT Self-Tapping Screw w/washer
圓頭十字墊圈螺絲
Body Clip
車殼R型插銷
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
Swing Post Screw
轉向曲柄固定螺絲
5x8x2.5mm
Ball Bearing
軸承
6mm(L)
Ball Stud
球頭座
2.6x12mm
F/H Self-Tapping Screw
平頭十字螺絲
2.6x8mm
F/H Self-Tapping Screw
平頭十字螺絲
2x12mm
BT Philip Machine Screw
圓頭十字螺絲
2.5x5mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
R型插銷
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
M3 Lock Nut
止鬆螺帽
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP7 Shock Absorber 避震器組
10
維修說明書及零件包型錄
1/10 SCALE NITRO POWERED 4WD TOURING CAR SERIES
1:10 引擎動力四驅房車系列
本套件所附之零件可能跟圖示有所差異。因產品後續之設計研發或功能不斷改善之原因，我們將保留產品規格變更權力，不再另行通知使用者。
This radio control model car is not a toy! Before beginning assembly, please read this manual thoroughly.
本產品為高性能模型非一般玩具，組裝與操作前請詳閱本產品說明書。
Indicates the assembly step number and the
parts that are to be assembled.
Displays ac tual size drawings, and part
quantities used.
All parts, except screws, are identified by its
order numbers. When purchasing spare parts,
identify the part required and cross reference
this to the spare parts list in the end of this
maunal, which shows the purchasable spare
parts and the corresponding order numbers.
This instruction manual uses several symbols.
Pay careful attention to them dur ing
construction. Details are given at the bottom
of each page.
顯示組立步驟及需組立之零件部位
零件實際對照尺寸及使用數量
請比對零件形狀以及後附零件料號對照圖示找
出需求零件料號
操作說明符號可更有效協助組裝者使用此說明
書，請依說明書符號指示進行組裝步驟
A:
B:
C:
D:
A:
B:
C:
D:
說明書使用方式
符號說明
You may also use silicone oil to replace grease for the differentials. Fill up to 80%. We
recommend using #7000 silicone oil for the front differential and # 10000 silicone oil for
the rear differential. Change the viscosity of the silicone oil according to track conditions
and your driving style.
玩家可依需求選購不同番號之差速矽油來取代原廠組裝使用之黃油。裝填時液面請勿超過
差速本體上緣(約八分滿即可)。進階玩家建議于前差速組使用#7000號之差速矽油，後差
速組使用#10000號之差速矽油。差速矽油需另外採購。玩家可依操作習慣及操作路面情況
選擇適合濃度之矽油來調整差速反應。
Put the clutch steel ball into the hole on the 2-Speed clutch.
Next, tighten the set screw to the 2-Speed spring until the spring
bottoms out, then unscrew 1 1/2-1 3/4 turns. This is the factory
setting of the 2-Speed. Adjust accordingly to track conditions.
將離合甩片鋼珠及彈簧 依序放入離合器 本體，將固定螺 絲鎖到
底後再鬆開1 1/2-1 3/4圈(注意!請勿將固定螺絲鎖死，如此將造
成彈簧失效)，進階玩家可依場地需求調整換檔時間。
Thetiresandwheelsinyourkitmayvaryfrom
thoseshowninthepictures.ThunderTigeris
constantlyworkingtoupgradeourkitsandwe
reservetherighttochangespecificatioins
withoutpriornotice.
本套件所附之輪胎與輪轂可能跟圖示有所差異。
因產品後續之設計研發或功能不斷改善之原因，
我們將保留產品規格變更權利，不再另行通知使
用者。
Leave one unit of drive axle for
later step.
將剩餘組件留待接下步驟組裝
8x14x4mm
Ball Bearing
軸承
2 Speed Spring
2段變速彈簧
6x9mm
Washer
墊圈
Top View
上視圖
Firmly tighten the set screw onto the flat spot.
將固定螺絲鎖附於變速軸平面上
5x8mm
Washer
墊圈
3x19mm
Pin
銷
3x5mm
Washer
墊圈
4.4x0.8mm
O-Ring
O型環
2.5x14mm
F/H Philip Machine Screw
平頭十字螺絲
8
4
4
4
4
2
2
1
3mm
Clutch Steel Ball
離合甩片鋼珠
1
3x6mm
Cap Screw
彈簧固定螺絲
14x10.5x0.1mm
Diff Shim
差速箱墊片
1
2
5x14x5mm
Ball Bearing
軸承
2
2.9x1.8mm
O-Ring
O型環
2
4x6mm
Set Screw
無頭內六角固定螺絲
2.5 x 5 mm
F/H Philip Machine Screw
平頭十字螺絲
1
6
4
2
2
1
2
1
2
2
4
STEP9 Steering Servo轉向伺服機 / Throttle/Brake Control Servo油門/煞車伺服機
STEP10 Radio Box 電池盒
STEP7 Shock Absorber 避震器組
11
〈Front Shock Tower〉
〈前避震器支架〉
In the chassis set, these dog bones have
been assembled in one-piece unit.
原廠已組配完成
In the chassis set, these dog bones have been
assembled in one-piece unit.
原廠已組配完成
Note direction
注意組裝方向
Note: !!!The use of the servo spacer may very
depending on the manufacturer's stock servo
you purchased. Check the servo to see if a
spacer is needed.
注意!!!由於市售伺服機規格不一，伺服機的
安裝調整請依各家廠牌伺服機實際安裝情況為
準來使用調整墊片。
3x10mm
BT Philip Tap Screw W / Washer
圓頭十字墊圈螺絲
6mm(S)
Ball Stud
球頭座
Marked "T" for Thunder Tiger stock servo. Find the appropriate servo horn mount for your
servo from the chart below. Install the servo horn arm with the stock mounting screw.
See the graphic for the correct neutral angle.
標示"T"搭配原廠伺服幾使用。請參考列表找尋適合各家廠牌伺服機所使用之拉桿座，然後
配合拉桿鎖附於伺服機上。
拉桿角度請依圖示調整於中立位置(約90度)。
Thread servo cord through.
將伺服機連接線/插頭依圖示穿進電池盒。
〈Rear Suspension〉
〈將後擺臂懸吊組結合於底板上〉
Connect as per instruction manual
依說明書指示將伺服機及電源開關連結於接收機
〈Rear Chassis Brace〉
〈將後補強版結合於後懸吊組與電池盒上〉
Thread antenna cord through the tubing.
將天線穿過套管並套上黑色護套 〈Radio & Servo Tray Unit〉
〈將電池盒結合於底板上〉
〈Front Suspension〉
〈將前擺臂懸吊組結合於底板上〉
Cut the silicone tube to 265mm length
for the fuel tube.
將油管裁切成265mm之長度做為輸油管
Cut the silicone tube to 195mm length
for the pressure tube.
將油管裁切成195mm之長度做為回壓管
Pass tube through tube clip. Squeeze
the end of pressure tube into the hole in
the tuned pipe about 10mm.
將油管固定於油管夾上並將回壓管塞 入
排氣管回壓接孔內約10mm後固定
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x12 mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
5x10x4mm
Ball Bearing
軸承
5x8x2.5mm
Ball Bearing
軸承
3x6mm
Socket Hex Machine Screw
內六角固定螺絲
3x28mm
Socket Hex Machine Screw
內六角固定螺絲
3x10mm
Socket Hex Machine Screw
內六角固定螺絲
3mm
Washer
墊圈
3mm
Spring Washer
彈簧墊圈
5x8mm
Washer
鋼迫緊板
3x8mm
BT Machine Screw
圓頭十字螺絲
Tighten the screws with one sheet of paper inserted
between both gears.
使用紙片調整主齒與驅動齒之間的間隙至適中位置。
Fuel Tube & Tuned Pipe
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
M3 Lock Nut
止鬆螺帽
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
3x8mm
F/H Philip Machine Screw
平頭十字螺絲
3x10mm
F/H Philip Machine Screw
平頭十字螺絲
Body Clip
車殼R型插銷
Install the tire onto the wheel. Glue the tire to the wheel with instant glue in four spots around the tire on both sides.
將輪胎(含內襯)與輪轂結合並在胎緣內側點上快乾膠黏合。
Warning: Follow the adhesive instructions for proper use and safety. Wear eye and hand protection.
注意!!!使用快乾膠時請注意安全，最好戴上手套及護目鏡以避免危險。
4mm
Washer
墊圈
4x12mm
Socket Hex Machine Screw
內六角固定螺絲
Cover the shaft with cloth before
griping it with pliers.
組裝避震球頭時，可以用布料包覆
芯軸，以避免芯軸被尖嘴鉗刮傷。
Ensure the piston move
smoothly.
最後再確認避震器活塞
是否移動順暢無阻
Note Direction
This side face forward.
此面朝前
Marked "L"
標示 "L"
〈For Right〉
〈右側組件〉
〈For Right〉
〈右側組件〉
LR
2
4
2
4
2
4
2
4
4
2
2
2
2
4
4
2
2
2
4
2
2
2
2
3
2
4
Rear
此面朝後
Engine Assembly
引擎組立圖
1
1
2
8
Pull down the piston and
slowly fill in the silicon oil.
The factory set-up of the
shock is #500 of silicon oil
for the front and rear shock
absorbers.
重新裝填矽油時，請先將活
塞及避震軸下拉，然後緩注
入避震器矽油于套筒內。
原廠避震器設定為前後避震
器皆使用#500號矽油。
Then gently move the shaft/piston
up and down to get rid of the
bubbles.
緩慢的將活塞及避震軸上下移動
使得套筒之氣泡能快點消失。
Add silicon oil one more
time up to the brim.
等所有氣泡都消失後再將液
面補滿
Put the shock bladder onto
the shock body, wipe off
excess oil and tighten the
shock cap.
將避震器封套置於套筒上
端並下壓結合，擦拭多餘
之矽油並鎖上避震器上蓋
Silicon oil
矽油
Piston 活塞
2
2
2
3
3
Tire/Wheels 輪胎及輪轂
6
2
2
2
1
2
1
2
3
1
1
1
1
4
6
1
2
4
1
1
3
2
5
4
4
4
8
4
D
說明書導讀
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Apply grease
使用潤滑油膏(黃油)
A d j u s t t h e
backlash with the
shims.
用來調整差速器
本體與齒輪箱之
間 距 ， 減 少 共
振。
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Marked "S-CM"
標示 "S-CM"
Apply grease
使用潤滑油膏(黃油)
Hint
組裝提示
Hint
組裝提示
4
3
2
1
〈For Right〉
〈右側組件〉
〈Rear Shock Tower〉
〈後避震器支架〉
2
1
LRx2
2
14x10.5x0.1mm
Diff Shim
差速箱墊片
STEP8
3x8mm
BT Philip Machine Screw
圓頭十字螺絲
3x18mm
BT Philip Machine Screw
圓頭十字螺絲
Steering Bellcrank 轉向曲柄組
Front Chassis Brace
前補強板
2
2
No.6194-F
1
1
Marked "S-ST"
標示 "S-ST"
Marked "S-ST"
標示 "S-ST"
Marked "T"
標示 "T"
Marked "T"
標示 "T"
Hint
組裝提示
Battery
電池盒
2.9x1.8mm
O-Ring
O型環
3
x2
Hint
組裝提示
Hint
組裝提示
〈Throttle Linkage〉
〈伺服機油門拉桿〉
Hint
組裝提示
Tube clip 油管夾
Hint
組裝提示
Attach the shock eyelet onto
the shock shaft until it reaches
the mark line on the shaft
將避震球器頭鎖附於芯軸直到
球頭上緣到達刻線。
TOMAHAWK VX PARTS LIST
PD9108
PD9109
PD9110
PD6601-R
PD9112
PD9113
9262
PD9114
PD9115
PD9116
PD9117
PD9118
PD9119
PD9120
PD9121
PD9122
PD0668
PD0669
PD0880
PD0874
PD0973
PD0978
PD0980
PD0982
PD1002
PD1191
PD1192
PD1244
PD1338
PD1532
PD1533
PD1534
PD1569
PD1572
PD1598
PD1683
PD2488
PD6307
PD7081
PD7193
PD7419
PD7441
PD7466
PD7469
PD7475
PD8178
PD8205
PD9123
PD9124
PD9125
PD9126
PD9129
PD9130
PD9131
PD9132
PD9133
PD9134
TH/BK SERVO HORN SET
BODY POST SET
HEX ADAPTER SET
5-SPK WHEEL ,26mm(CHROME/RED)
10-SPK WHL ,26mm(BLACK)
8-SPK WHL,26mm(BLACK)
1/10 AIR CLEANER, DUAL FOAM
PAINTED Z-TUNE
CLEAR Z-TUNE W/DECAL
Z-TUNE DECAL SET
PAINTED 350Z
CLEAR 350Z W/DECAL
350Z DECAL SET
PAINTED XANAVI GT-R R34
CLEAR XANAVI GT-R R34 W/DECAL
XANAVI GT-R R34 DECAL SET
BT M. SCREW(20),M3x10
BT M. SCREW(20),M3x12
BT P.M. SCREW(20),M3x25
BALL BEARING SET(4), d5xD10xW4
WASHER(20), 4mm
E-CLIP(20), 4mm
SPRING WASHER(20)
NYLON STRAP(20), SMALL
BALL BEARING SET(4), d5xD8xW2.5
CTP.M.SCREW(20), M3x8
CTP.M.SCREW(20), M3x10
LOCK NUT(10), M3
SKH.M SCREW(20),M3x12
BT P.M. SCREW(20),M3x8
BT P.M. SCREW(20),M3x10
BT P.M. SCREW(20),M3x12
E-CLIP(20),2.5mm
BALL BEARING(2), d6xD12xW4
SET SCREWS(20), M4x4
BT P. TAP SCREW , M3x10
BT P.M. SCREW(20), M3x18
SK H.M SCREW (20), M3x6
CTP.M.SCREW(20), M3x12
BODY CLIPS(20), HNLR5
BALL BEARING SET(4), d5xD14xW5
BALL BEARING SET(4), d8xD14xW4
BALL BEARING SET(10), d5xD11xW4
SKH.M SCREW(10),M4x12
SKH.M SCREW(10),M3x10
O-RING(20)
BHP SCRDW(20), M3x6
SKH.M SCREW(20), M3x28
CT P.M.SCREW(20), M25x12
CT P.M.SCREW(20), M25x5
SET SCREW(20), M4x10
BALL BEARING(4), 10x15x4
BALL BEARING(4), 5x8x2.5mm
CTP. TAP SCREW(20) ,M26x10
CTP. TAP SCREW(20) ,M26x12
BT P. TAP SCREW ,M2x4
1/10 SLICK TIRE W/FOAM,26mm
32
天線零件包、黑
避震器上蓋
避震器空氣活門
活塞
差速器本體
前差速箱上下蓋組
後差速箱上下蓋組
傳動軸套
差速組齒輪
差速小傘齒(13T)
差速大傘齒(34T)
單向軸承座組
主齒輪組(43/38T)
兩段變速本體
甩片座組
兩段變速軸
中差座上蓋
中差座
剎車組
離合器罩
飛輪組
離合器齒輪
離合器甩塊組
引擎固定座
前防撞板
防撞泡綿
避震器支架
前擺臂組
後擺臂組
轉向臂
C型座組
前傳動軸
軸承針組
拉桿組
擺臂軸套
擺臂軸
前投影板（0度）
後投影板（2.5度）
轉向曲柄組
轉向軸
中央傳動軸
補強板組
後輪座
開關盒蓋&墊片組
接收機盒
車底盤
後傳動軸
油箱組
消音器
彎管接頭
排氣彎管
避震器組
避震器彈簧（2.5x1.8mm）藍
避震器軸
避震器配件
避震器球頭拉桿
球頭座，長
球頭座，短
油門煞車拉桿組
轉向拉桿緩衝組
中文名稱 PART# DESCRIPTION NOTE
油門拉桿緩衝組
車殼支柱
六角輪鼓轉換座組
5爪輪轂 ,26mm(電鍍紅)
10爪輪轂 ,26mm(黑)
8爪輪轂 ,26mm(黑)
空氣濾清器
完成車殼，Z-TUNE
透明車殼及貼紙，Z-TUNE
貼紙，Z-TUNE
完成車殼車殼，350Z
透明車殼及貼紙，350Z
貼紙，350Z
完成車殼車殼，XANAVI GT-R R34
透明車殼及貼紙，XANAVI GT-R R34
貼紙，XANAVI GT-R R34
半圓頭內六角螺絲(20), M3x10
半圓頭內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x25
滾珠軸承(4), d5xD10xW4
華司(20), 4mm
E型扣環(20), 4mm
彈簧墊圈(20)
固定束帶(20)
滾珠軸承(4), d5xD8xW2.5
平頭十字螺絲(20), M3x8
平頭十字螺絲(20), M3x10
止鬆螺帽(10), M3
內六角螺絲(20), M3x12
圓頭十字螺絲(20), M3x8
圓頭十字螺絲(20), M3x10
圓頭十字螺絲(20), M3x12
E型扣環(20), 2.5mm
滾珠軸承(2), d6xD12xW4
無頭內六角螺絲(20), M4x4
圓頭十字墊圈螺絲 , M3x10
圓頭十字螺絲(20), M3x18
內六角螺絲 (20), M3x6
平頭十字螺絲(20), M3x12
R型插銷(20)
滾珠軸承(4), d5xD14xW5
滾珠軸承(4), d8xD14xW4
滾珠軸承(10), d5xD11xW4
內六角螺絲(10), M4x12
內六角螺絲(10), M3x10
O型環(20)
圓頭十字螺絲(20), M3x6
內六角螺絲(20), M3x28
平頭十字螺絲(20), M25x12
平頭十字螺絲(20), M25x5
無頭內六角螺絲(20), M4x10
滾珠軸承(4), 10x15x4
滾珠軸承(4), 5x8x2.5mm
平頭墊圈十字螺絲(20), M26x10
平頭墊圈十字螺絲(20), M26x12
圓頭十字螺絲, M2x4
光頭胎, 26mm
中文名稱
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
1
PD9140 FLAME DECAL, BLUE
火焰貼紙,藍
PD9141 FLAME DECAL, YELLOW
火焰貼紙,黃
PD9142 FLAME DECAL, RED
火焰貼紙,紅
PD9143 CFRP BUMPER TOP PLATE
碳纖維前防撞上板 PD9144
CFRP FRONT SHOCK TOWER
碳纖維前避震器支架 PD9145
CFRP REAR SHOCK TOWER
碳纖維後避震器支架
PD9147 CFRP FR CHASSIS BRACE
碳纖維前補強板 PD9148
CFRP RR CHASSIS BRACE
 碳纖維後補強板(配合PD9150)
PD9146 CFRP BULK LOWER COVER
碳纖維差速箱下蓋板
PD9149 ALUM. REAR TOE BLOCK
後投影板(2 /3 )
PD9150 LIGHTENED ENG. MOUNT
引擎固定座(非手拉引擎)
PD9151 FLYWHEEL( STR BOX)
飛輪組(適用起動台)
PD9159 SHOCK SPRING,YELLOW
避震器彈簧,黃 (適中)
PD9158 FIRE BLADE TIRE 26mm
高速火炎輪胎
PD9156 HEX WHL CAP SCREW
六角輪胎固定螺絲
PD9155 ALUMINUM SHOCK SET
避震器套筒組
PD9154 ALUMINUM UPPER ROD
上擺臂拉桿組
PD9153 ALUMINUM TURNBUCKLE SET
轉向調整拉桿組
PD9160 SHOCK SPRING,RED
避震器彈簧,紅 (中硬)
PD9161 SHOCK SPRING,BLACK
避震器彈簧,黑 (特硬)
PD9162 SHOCK SPRING,WHITE
避震器彈簧,白 (特軟)
TOMAHAWK VX OPTION PART LIST
33
PART# DESCRIPTION NOTE
PD7714
PD7722
PD7723
PD7724
PD7876
PD7968
PD7969
PD9140
PD9141
PD9142
PD9143
PD9144
PD9145
PD9146
PD9147
PD9148
PD9149
PD9150
PD9151
PD9153
PD9154
PD9155
PD9156
PD9159
PD9160
PD9161
PD9162
OP OUTDRIVE CUP
ALUM STEERING BLOCK SET
ALUM CASTER BLOCK SET
ALUM HUB CARRIER SET
ALUM HEX ADAPTER
ALUM STEERING BELLCRANK
ALUM STEERING SLIDER
FLAME DECAL, BLUE
FLAME DECAL, YELLOW
FLAME DECAL, RED
CFRP BUMPER TOP PLATE
CFRP FRONT SHOCK TOWER
CFRP REAR SHOCK TOWER
CFRP BULK LOWER COVER
CFRP FR CHASSIS BRACE
CFRP RR CHASSIS BRACE
ALUM REAR TOE PLATE,2 /3
LIGHTENED ENG. MOUNT(NON-PULL START)
FLYWHEEL( STR BOX)
ALUMINUM TURNBUCKLE SET
ALUMINUM UPPER ROD
ALUMINUM SHOCK SET
HEX WHL CAP SCREW
SHOCK SPRING(2.5x1.8mm),YELLOW
SHOCK SPRING(2.5x1.9mm),RED
SHOCK SPRING(2.5x2.0mm),BLACK
SHOCK SPRING(2.5x1.6mm),WHITE
34
鋼制傳動軸套
鋁合金改裝轉向臂
鋁合金改裝C型座組
鋁合金改裝後輪座
鋁合金改裝六角輪轂轉換器
鋁合金改裝轉向搖臂
鋁合金改裝轉向曲柄
火焰貼紙,藍
火焰貼紙,黃
火焰貼紙,紅
碳纖維前防撞上板
碳纖維前避震器支架
碳纖維後避震器支架
碳纖維差速箱下蓋板
碳纖維前補強板
碳纖維後補強板
碳纖維後投影板（2 /3 ）
引擎固定座（適用非手拉引擎）
飛輪組（適用起動台）
轉向調整拉桿組
上擺臂拉桿組
避震器套筒組
六角輪胎固定螺絲
避震器彈簧(2.5x1.8mm),黃
避震器彈簧(2.5x1.9mm),紅
避震器彈簧(2.5x2.0mm),黑
避震器彈簧(2.5x1.6mm),白
中文名稱
Marked "R"
標示 "R"
Antenna
天線
Hint
組裝提示
Use 6 mm preload spacer for front. Use 6 mm preload spacer for rear.
使用6mm避震器套筒調整夾片來調整避震器彈簧之鬆緊度
〈Front Shock Absorbers〉
〈將前避震器與前擺臂懸吊結合〉
〈Rear Shock Absorbers〉
〈將後避震器與後擺臂懸吊結合〉
Compress the spring
and install spring cup.
將下定位套固定于彈
簧下緣。
Marked "S-CM"
標示 "S-CM"
Steering Servo Type
轉向伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
TH/BK Servo Type
油門/煞車伺服機
Ace R/C S1903/ S2008MG
ACE R/C DS1015/DS0313
Airtronics / Sanwa
Futaba
Hitec
Servo Horn Mount
拉桿座
T
T
A
T
H
Body Clip
車殼R型插銷
4
Note direction
Cross with servo
注意安裝方向
與伺服機呈90°
RX
TH
ST
10mm
CA
Brake Disc
煞車片
Adjust the backlash
with the shims.
用來調整差速器本體
與齒輪箱之間距，減
少共振。
1mm 2mm
4mm 6mm
T
Back
背面
T
Back
背面
TH / BK
油門 /煞車伺服機
ACE R/C S1903/ S2008MG
ACE R/C DS1015/DS1313
Airtronics / Sanwa
Futaba
Hitec
Spacer
調整墊片
thin
thick + thin
See Note:
See Note:
See Note:
90°
Neutral
中立點
ON
OFF
BATT
CH2
CH1
Black to Black
Red to Red
黑對黑、紅對紅
1
3x6mm
BT Philip Machine Screw
圓頭十字螺絲
Tube Clip
油管夾
Pressure Tube 回壓管
Fuel Tube 輸油管
Pressure Tube 回壓管
Adjust height to suit body.
調整車殼R型插銷來安裝車殼
Tire insert foam
輪胎海綿內襯 5.5mm
5.5mm
5.5mm
Antenna Hole
天線孔
Batteries not included in the kit
此套件不含電池
Check O-ring Inside
請先確認內部O型環已置入
PD9053 FRONT BULK SET
前差速箱上下蓋組
PD9052 REAR BULK SET
後差速箱上下蓋組
PD9054 OUTDRIVE CUP SET
傳動軸套
PD9051 DIFFERENTIAL CASE
差速器本體
PD9055 DIFFERENTIAL GEAR SET
差速組齒輪 PD9058 DIFF SPUR GEAR 34T 差速大傘齒(34T)
PD9057 DRIVE PINION SET 13T
差速小傘齒(13T)
PD8098 SHOCK PISTON SET
活塞
PD9059 ONE WAY BEARING SET
單向軸承座組
PD9060 1ST/2ND SPUR GEAR
主齒輪組
PD9061 2 SPD. CLUTCH HUB
兩段變速本體
PD9062 2 SPD. CLUTCH SET
甩片座組
PD9063 2 SPD. DRIVE SHAFT
兩段變速軸
PD9064 CTR DIFF. COVER
中差座上蓋
PD9065 CTR DIFF. MOUNT
中差座 PD9066 DISC BRAKE SET 剎車組 PD9067 2 SPD. CLUTCH BELL 離合器罩
PD9068 FLY WHEEL
飛輪組
PD9069 1ST/2ND PINION GEAR
離合器齒輪 PD9070 CLUTCH SHOE SET 離合器甩塊組 PD9071 ENGINE MOUNT 引擎固定座
PD9072 BUMPER SET
前防撞板 PD9073 URETHANE BUMPER
防撞泡綿
PD9074 SHOCK TOWER SET
避震器支架
PD9075 FRONT SUSP. ARMS
前擺臂組
PD9076 REAR SUSP. ARMS
後擺臂組
PD9077 STEERING BLOCK SET
轉向臂 PD9078 CASTER BLOCK SET C型座組 PD9079 FRONT UNINI SHAFT 前傳動軸
PD9080 OUTER HINGE PIN SET
軸承針組
PD9082 SUSP. ARM MOUNT BUSHING
擺臂軸套
PD9081 UPPER LINK SET
拉桿組
PD9083 INNER HINGE PIN SET
擺臂軸
PD9084 FRONT TOE PLATE
前投影板(0)
PD9085 REAR TOE PLATE
後投影板(2.5)
PD9086 SWING RACK SET
轉向曲柄組
PD9092 RADIO TRAY
接收機盒
PD9091 SWITCH PLATE & SPACERS
開關盒蓋&墊片組
PD9090 HUB CARRIER SET
後輪座
PD9089 CHASSIS BRACE SET
補強板組
PD9088 CTR. DRIVE SHAFT SET
中央傳動軸
PD9087 SWING POST SCREW
轉向軸
PD9093 CHASSIS
車底盤
PD9094 REAR UNINI SHAFT
後傳動軸
PD9095 FUEL TANK
油箱組
PD9096 MUFFLER
消音器
PD9097 SILICONE TUBING
彎管接頭
PD9098 MANIFOLD
排氣彎管
(2)
(2) (4)
(8) (8) (8)
PD9099 SHOCK SET
避震器組
PD9100 SHOCK SPRING BLUE
避震器彈簧，藍(中軟)
PD9101 SHOCK SHAFT
避震器軸
PD9103 SHOCK EYELET
避震器球頭拉桿
PD9104 BALL STUD (L)
球頭座（長） PD9105 BALL STUD (S)
球頭座（短） PD9106 TH/BK LINKAGE SET 油門煞車拉桿組 PD9107
STEERING SERVO HORN SET
轉向拉桿緩衝組
PD9108 TH/BK SERVO HORN SET
油門拉桿緩衝組
PD9109 BODY POST SET
車殼支柱
PD9110 HEX ADAPTER SET
六角輪鼓轉換座組
PD6601-R
5-SPK WHEEL ,26mm(C/R)
5爪輪轂,26mm(電鍍紅)
PD9114 PAINTED BODY SET
完成車殼，SKYLINE Z-TUNE
PD9113
8-SPK WHL,26mm(BLACK)
8爪輪轂,26mm(黑)
PD9112
10-SPK WHL ,26mm(BLACK)
10爪輪轂,26mm(黑)
PD9117 PAINTED BODY SET
完成車殼，NISSAN 350Z
PD9120 PAINTED BODY SET
完成車殼，XANAVI GT-R (R34)
PD9115 CLEAR BODY W/DECAL
透明車殼及貼紙，SKYLINE Z-TUNE
PD9116 DECAL SET
貼紙，SKYLINE Z-TUNE
PD9118 CLEAR BODY W/DECAL
透明車殼及貼紙，NISSAN 350Z
PD9119 DECAL SET
貼紙，NISSAN 350Z
PD9121 CLEAR BODY W/DECAL XANAVI GT-R (R34)
透明車殼及貼紙
PD9122 DECAL SET XANAVI GT-R (R34)
貼紙
PD0668 M3x10 (20)
PD0669 M3x12 (20)
PD7193 HNLR5 (20)
PD1569 2.5mm(20)
PD0978 4mm(20)
PD1572 d6xD12xW4(2)
PD9129 d10xD15xW4(4)
PD7441 d8xD14xW4(4)
PD7419 d5xD14xW5(4)
PD1002 d5xD8xW2.5(4)
PD9130 d5xD8xW2.5(4)
PD7466 d5xD11xW4(4)
PD0874 d5xD10xW4(4)
PD6307 M3x6B (20)
PD1338 M3x12B (20)
PD7475 M3x10B (20)
PD9123 M3x28B (10)
PD7469 M4x12B (10)
PD2488 M3x18B (20)
PD0880 M3x25B (20)
PD1534 M3x12B (20)
PD1533 M3x10B (20)
PD1532 M3x8B (20)
PD8205 M3x6B (20)
PD1191 M3x8B (20)
PD1192 M3x10B (20)
PD7081 M3x12B (20)
PD9124 M25x12B (20)
PD9125 M25x5B (20)
PD9131 M2.6x 10(20)
PD9132 M2.6x12(20)
PD0982 SMALL(20)
PD1683 M3x10B (20)
PD9133 M2x4B(20)
PD1598 M4x4B (20)
PD9126 M4x10B (20)
PD0973 4 (20)
PD1199 3B (20)
PD0980 3mm
PD9134
1/10 SLICK TIRE W/FOAM
光頭胎26mm
BALL BEARING
滾珠軸承
SKH.M SCREW
內六角螺絲
BHP SCREW
圓頭十字螺絲 CT P.M.SCREW
平頭十字螺絲
CTP. TAP SCREW
平頭墊圈十字螺絲
SET SCREW
無頭內六角螺絲
BT P. TAP SCREW
圓頭十字墊圈螺絲
PD1244 3mm
LOCK NUT
止鬆螺帽
PD8178 2.9xW1.78(20)
O-RING
O型環
BT M. SCREW
半圓頭內六角螺絲
E-CLIP
E型扣環
SPRING WASHER
彈簧墊圈
WASHER
華司
BODY CLIPS
R型插銷
NYLON STRAP SMALL
固定束帶
PD8088-1 SHOCK CAP
避震器上蓋
PD8093 SHOCK BLADDER
避震器空氣活門
(4)
(10)
2
Round Tap Screw
圓頭十字螺絲
5.5mm
5.5mm
(4)(4)(4)
(4)(4)(4)
PD9102 SHOCK ACCESSORIES
避震器配件
(4) (4) (4)
1.2 1.3 1.4
(4)
SOFT 2.5x1.8mm
SOFT軟
2°
3°
FOR NON-PULL START ENGINE
FOR STARTER BOX
MEDIUM適中
HARD硬
EXTRA HARD中硬
EXTRA SOFT中軟
5-SPOKE WHEEL 5爪輪轂組
PD6601-L C/BLUE 雙色電鍍藍 , 26mm
PD6601-P C/PURPLE 雙色電鍍紫, 26mm
PD6601-Y C/YELLOW 雙色電鍍黃, 26mm
SPRINT DRIFT TIRE 疾速甩尾胎
PD7643 , 26mm
PD7644 , 30mm
2.8x1.9mm
O-Ring
O型環
8
Apply grease
使用潤滑油膏(黃油)
Always adjust the front and rear bushings
at the same time. You car may not run
stable if front and rear bushings are
unbalanced.
調整時請同時更換前後擺臂軸套。不平
衡的設定將增加車輛行駛的不穩定性。
By replacing the suspension arm mount
bushings (setup of roll center), you can
acquire different handling and steering
responses according to the different track
conditions. The kit included various spare
bushings for your further replacement.
藉由更換擺臂軸套來改變車子的滾動中
心之高低有助於穩定方向與控制轉向以
適應不同路面及操控之需求。
Roll Center Adjustment:
調整滾動中心
Roll
Center
Position
Low Speed Track High Speed Track
多彎高速路面
中間
(原廠設定)
Low Mid. Low High
Medium
(Factory Set-up)
Mid. High
滾動中心位置 最低 偏低 最高偏高
Track
路況
Top View
上視圖
Side View
側視圖
Neutral
中立點
90°
Manual Format 說明書使用方式
Symbols Used Throughout The Manual 符號說明
STEP1 Front Differential 前差速組 / Rear Differential 後差速組
STEP2 2-Speed Transmission Unit 2 段變速組
STEP3 Front Differential Unit前差速箱
STEP4 Front Suspension 前擺臂懸吊組
STEP5 Rear Differential Unit 後差速箱
STEP6 Rear Suspension 後擺臂懸吊組
STEP7 Shock Absorber 避震器組
STEP8 Steering Bellcrank 轉向曲柄組
STEP9 Steering Servo 轉向伺服機 / Throttle/Brake Control Servo 油門 /煞車伺服機
STEP10 Radio Box 電池盒
STEP11 Installation of Rear End 結合後擺臂懸吊組
STEP12 Installation of Radio Box 結合電池盒
27
33
STEP13 Installation of Front End 結合前擺臂懸吊組
STEP14 Installation of 2-Speed Transmission Unit 結合2段變速組
STEP15 Installation of Fuel Tank 結合油箱
STEP16 Engine Set 引擎與離合器罩
STEP17 Muttler & Fuel Tube 消音器與油管
STEP18 Throttle/Brake Linkage 伺服機油門/煞車連桿
STEP19 Front Bumper 前防撞板 / Front Body Mounts 前車殼支柱
STEP20 Tire / Wheels 輪胎及輪轂
STEP21 Body Shell 車殼
TOMAHAWK EXPLODED VIEW 爆炸圖檢索
TOMAHAWK VX PART LIST 零件表及圖示
TOMAHAWK VX OPTION PART LIST 改裝零件表及圖示
WHEEL & TIRE OPTION PART LIST 輪轂和輪胎改裝零件表及圖示
P.2
P.2
P.3
P.3
P.5
P.5
P.7
P.8
P.10
P.12
P.13
P.14
P.16
P.16
P.17
P.18
P.18
P.19
P.20
P.20
P.21
P.21
P.22
P.23
P.27
P.33
P.34
28mm
STEP17 Muttler & Fuel Tube 消音器與油管
PART# DESCRIPTION NOTE
中文名稱
HIGH GRIP TIRE,高捉地力胎,26mm
PD1784,26mm
PULSE DRIFT TIRE 脈衝甩尾胎
PD7645 , 26mm
PD7646 , 30mm
Roll center adjustment refers to
Page 8
滾動中心的調整請參考第8頁之
說明
Factory Set-up
原廠設定
Assem ble Earlier
Refer to Page 5
參考第5頁
arm
mount
bushings
擺臂軸套
Rear
此面朝後
(2)
(2)
(2)
EXTRA SOFT 2.5x1.6mm
MEDIUM 2.5x1.8mm HARD 2.5x1.9mm EXTRA HARD 2.5x2.0mm
PD6601-L
PD6601-P
PD6601-Y
PD6681
PD6682
PD6682-B
PD7649
PD7650
PD7699
PD7700
PD1784
PD7643
PD7644
PD7645
PD7646
PD9158
5-SPOKE WHEEL(C/BLUE), 26mm (2)
5-SPOKE WHEEL(C/PURPLE), 26mm (2)
5-SPOKE WHEEL(C/YELLOW), 26mm (2)
5-SPOKE WHEEL(CHROME), 26mm (2)
5-SPOKE WHEEL(WHITE), 26mm (2)
5-SPOKE WHEEL(BLACK), 26mm (2)
RACING DISH WHEEL(WHITE), 26mm (2)
RACING DISH WHEEL(WHITE), 30mm (2)
10-SPK SPORT WHEEL(WHITE), 26mm (2)
10-SPK SPORT WHEEL(WHITE), 30mm (2)
HIGH GRIP TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 26mm
SPRINT DRIFT TIRE(2), 30mm
PULSE DRIFT TIRE(2), 26mm
PULSE DRIFT TIRE(2), 30mm
FIRE BLADE TIRE(2), 26mm
5爪輪轂組(2), 26mm(雙色電鍍藍)
5爪輪轂組(2), 26mm(雙色電鍍紫)
5爪輪轂組(2), 26mm(雙色電鍍黃)
5爪輪轂組(2), 26mm(電鍍銀)
5爪輪轂組(2), 26mm(白)
5爪輪轂組(2), 26mm(黑)
蝶式輪轂(2), 26mm(白)
蝶式輪轂(2), 30mm(白)
10爪輪轂(2), 26mm(白)
10爪輪轂(2), 30mm(白)
高捉地力胎(2), 26mm
疾速甩尾胎(2), 26mm
疾速甩尾胎(2), 30mm
脈衝甩尾胎(2), 26mm
脈衝甩尾胎(2), 30mm
高速火炎輪胎(2), 26mm
5-SPOKE WHEEL 5爪輪轂組
PD6681 CHROME 電鍍銀, 26mm
PD6682 WHITE 白色 , 26mm
PD6682-B BLACK 黑色 , 26mm
RACING DISH WHEEL 蝶式輪轂
PD7649 WHITE 白色 , 26mm
PD7650 WHITE 白色 , 30mm
10爪輪轂
PD7699 WHITE 白色, 26mm
PD7770 WHITE 白色, 30mm
(2)
WHEEL & TIRE OPTION PART LIST
NO.2705 LED LIGHTING KIT
LED改裝燈組
AQ0802
AQ0803 AQ0804
AQ0801
NO.1340 ROTATING CAR STAND
旋轉調車架
1
1
2
3
3
4
4
〈Rear Body Post〉
〈後車殼之註〉
2
2
Marked ". ."
Toe-in 2.5°
標示 ". ."內傾角2.5°
Marked "."
標示 "."
PD7712 SHOCK CAP
天線
9262 AIR CLEANER,DUAC FOAM
空氣濾清器
(2)
(2)(2)
(2) (2) (2) (2)
Insert Foam Included.
PD7714 OUTDRIVE CUP
鋼制傳動軸套
4x10mm
SET Screw
無頭內六角螺絲
4
FOR PD9150
Insert Foam Included.
TOMAHAWK VX PARTS LIST
PD7968 ALUM STEERING BELLCRANK
鋁合金改裝轉向搖臂
PD7969 ALUM STEERING SLIDER
鋁合金改裝轉向曲柄
PD7722 ALUM STEERING BLOCK SET
鋁合金改裝轉向臂
PD7723 ALUM CASTER BLOCK SET
鋁合金改裝C型座組
PD7724 ALUM HUB CARRIER SET
鋁合金改裝後輪座
PD7876 ALUM HEX ADAPTER
鋁合金改裝六角輪轂轉換器
TOMAHAWK VX OPTION PART LIST