TMA Rivers Edge LD200 User manual

Get parts online at
www.HuntRiversEdge.com
PARTICIPATING MEMBER
PRODUCT MEETS
INDUSTRY STANDARDS
RECOGNIZED BY
P/N: 35640
C/N: 35483
REV3: 06/05/2020
© 2020 RETI
All Rights Reserved
Operator's Manual
MODEL LD200
LOCKDOWN
21-FT WIDE
Ladder Stand
Maximum Height
20’6” to shooting rail
Wear Your
Harness!
Maximum Field Rating
300 lbs
Tree Diameter Range
12” to 30”
PAT. WWW.ARDISAM.COM/PATENTS

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
2
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
INTRODUCTION
Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world class
treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free pleasure. Instructions
should be kept in a safe place and reviewed at least annually.
If for any reason you have a problem with your product or are missing any parts, DO NOT return to the retailer, contact Rivers
Edge® Customer Service Department at 800-345-6007 for assistance.
CONTENTS
Introduction/Warranty ..................................................................................................................................................................................................................2
Warnings.........................................................................................................................................................................................................................................3-4
Inspection and Maintenance ......................................................................................................................................................................................................4
Hardware Identication Chart................................................................................................................................................................................................5-7
Assembly Instructions ............................................................................................................................................................................................................ 8-16
Warnings.......................................................................................................................................................................................................................................... 17
Setup and Use Instructions.................................................................................................................................................................................................18-23
The Ultimate Shooting Rail Use Instructions...................................................................................................................................................................... 24
Finished Ladder............................................................................................................................................................................................................................. 25
Illustrated Parts Breakdown................................................................................................................................................................................................26-27
WARRANTY
RETI oers a one-year warranty for all components of the treestand. These warranties apply to the original owner with a proof of purchase. These warranties
begin on the date of purchase by the rst retail consumer and continue for the period specied above. These warranties apply to products that are not modied,
abused or used in a manner that deviates from the product’s intended usage. Minor fading in color is normal and is not covered by warranty. Any corrosion
of painted surfaces that occurs as a result of paint being removed or damaged is also not covered by warranty. RETI oers no other warranty expressed or
implied. Products for which warranty work has been approved must be sent directly to RETI and performed by RETI. To obtain warranty service and/or
replacement instructions, you must obtain prior approval from RETI before shipping your package to us by calling our customer service department
at 800-345-6007 or by writing to: Ardisam, Inc., P.O. Box 755, 1160 Eighth Avenue, Cumberland,WI 54829 for a return material authorization number
(RMA#). All items must be shipped prepaid. RETI will, at no charge, repair or replace, in RETI’s sole discretion, any product that satises the conditions stated
above. RETI retains the right to change models, specications and price without notice.
This equipment has been manufactured under strict quality and safety guidelines. As with any equipment of this type, full understanding of the instructions and
its use is mandatory and imperative for the safety of its user. RETI is not responsible for any damages or injuries sustained due to improper use or modication
of any of its products, or resulting from any use which deviates from the product’s intended usage. RETI is not responsible for any injuries sustained due to
failure to read and adhere to the instructions for use. Any misunderstanding or questions regarding the products of their use should be directed to RETI prior to
any use. All RETI treestands are sold with a full body harness (“Fall Arrest System”) that meets standards recognized by theTreestand Manufacturer’s
Association (“TMA”). It is the owner's sole responsibility to inspect the product regularly for damage, improper installation, or conditions that could jeopardize
the ultimate safety of the product. Failure to use or improper use of the provided Fall Arrest System may result in serious injury or death. ALWAYS wear the
provided Fall Arrest System while using this product. Owner is responsible to understand and follow product eld weight rating and must never
exceed maximum weight rating. RETI is not responsible for any malfunction or injury resulting from normal wear and tear, damage caused by improper use,
improper maintenance, negligence or accidents. This product, if used safely as intended, will provide trouble free service for the useful life of the product. We
hope you will enjoy the quality of our products for years to come, and have a safe hunt.

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 3
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE ASSEMBLY
STOP
MODEL LD200
MAXIMUM USE HEIGHT  20’6”TO SHOOTING RAIL
MAXIMUM OCCUPANCY  ONE 1
TOTAL WEIGHT LIMIT  300 LB
TREE DIAMETER RANGE  12”TO 30”
WARNING
This product carries strict height and weight restrictions.
Do Not use this product if you exceed the total weight
limit. Please note that the total weight limit includes the
user(s) and their equipment.
WARNING
When hunting from a treestand falls can occur any
time after leaving the ground causing injury or death.
Always wear a Fall Arrest System (FAS) comprising a full
body harness at all times after leaving the ground. You
must stay connected at all times after leaving the ground
while using climbing and hang-on treestands. Single
safety belts and chest harnesses are no longer allowed
and shall never be used. If you are not wearing a full body
harness properly attached to the tree that is protecting
you from a fall, do not leave the ground.
Read and understand all of the manufacturer’s Warnings
and Instructions and use all safety devices provided by
the manufacturer. Contact the manufacturer for any
questions. Failure to do so could result in injury or death.
Never exceed the total weight limit of the treestand.
Never use a treestand during inclement weather such as
rain, lightning, windstorms or icy conditions and end your
hunt and return to the ground if inclement conditions arise.
Never use a treestand while using drugs (even
prescription drugs) or alcohol.
Never use a treestand while feeling ill, nauseous or dizzy,
or if you have a prior medical condition that could cause
a problem, that is, heart condition, joints that lock-up,
spinal fusions, etc., or if you are not well rested. Never
sleep in stand.
Never use a treestand on a dead, leaning, diseased or
loose barked tree, or a utility pole. Always avoid electrical
power lines.
Never rely on a tree branch for support.
WARNING
Never jump or bounce on a treestand to seat it to the tree.
Pull up a bow, backpack, or rearm or other equipment
only after being secure in the treestand and a rearm
must be pulled up with it unloaded, chamber open, and
muzzle down.
Always inform someone of the hunting location, where
the treestand will be located and the expected duration
of the hunt.
A signal device such as a mobile phone, radio, whistle,
signal are or personal locator device (PLD) must be on
your person and readily available at all times.
Inspect the treestand and all safety devices each time
before use and Do Not store a treestand outdoors when
not in use.
Never modify your treestand in any way by making
repairs, replacing parts, or altering it except if explicitly
authorized in writing by the manufacturer.
Practice installing, adjusting and using your treestand at
ground level prior to using it at elevated positions. Study
your new stand to become familiar with all of its features
and design. Doing so will conrm that the product is
manufactured, assembled and installed correctly.
Instructions (written and video) shall be kept in a safe place
and reviewed at least annually. It is the responsibility of
the treestand owner to furnish the complete instructions
to any person who borrows or purchases the treestand.
Use at least three (3) people to install or take down a
ladder treestand.
The criss-cross straps/ropes and stabilization devices
must be attached before climbing to the platform.
When installing a ladder stand, always bounce on the
rst rung to set the ladder into the ground according to
manufacturer’s instructions before proceeding to climb
any higher.
Check every ladder section connection every time you
use the stand before you leave the ground. If ladder
sections are separating, do not use the stand.
Check the ground under the stand to make sure it is rm
and level. Sloping ground or uneven surface (one side on
a rock) can cause your ladder to tilt or shift o the tree as
you climb.
Always maintain three (3) points of contact when
climbing a ladder treestand. Proper three-point contact
means having either two feet with one hand or one foot
with two hands on the step portion of the ladder or
climbing aid at all times.

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
4
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
BEFORE EACH USE PERFORM THE FOLLOWING:
• Inspect all webbing, rope, cord, and strap assemblies for
wear or damage.
• Inspect cables and/or cable ends for damage or kinking.
• Inspect all hardware and chain components for damage or
wear.
• Inspect for any structural damage to product. (If any exists
stop use immediately and call RETI Customer Service.)
• Inspect all nut and bolt assemblies to be certain none are
loose.
• Inspect for any missing parts.
• Lubricate all pivot and slide together points with powder
graphite, petroleum jelly or silicone spray to prevent noise,
wear and rust.
• Inspect entire product for any rust, corrosion, cracks,
freezing, excessive heat or rotting damage that may eect
the safety of your product. Discard any questionable
product.
• Inspect entire product for any structural damage - pay
close attention to all weld locations. (Discard product if any
damage is found.)
• Using correct wrenches inspect all nut & bolt assembly
locations and snug up any that may be loose. Be careful not
to crush tubing when tightening!
• Inspect and check operation of all cables, cable ends, cord,
rope, webbing, and strap or chain assemblies. Replace
with RETI original replacement parts any item or assembly
that shows signs of wear, damage, kinking, or functions
incorrectly.
• Inspect seat for damage or wear. Replace any seat with
factory new that shows signs of structural damage or wear.
• Never modify your stand in any way by making repairs,
replacing parts, or altering by adding or attaching anything
to it except if explicitly authorized in writing by the
manufacturer.
INSPECTION AND MAINTENANCE
WARNING
Always lean forward as you climb and attach your harness
to the tree before securing the platform to the tree and
stepping onto the platform.
Never exceed the stated maximum use height.
Do Not use this product until you have watched the
online safety video, understand it, and practiced the
techniques for safe hunting discussed in this video. Video
can be found with the QR code and/or URL shown on
front cover of this manual.
Read and perform all inspection and maintenance tasks
before each and every use. Replace any questionable
components immediately with RETI original replacement
parts.
Do Not crush tubing when tightening bolt assemblies!
Identify and familiarize yourself with all parts before you
start. Bolt identication chart can be found in the back.
Double check assembly steps to be certain you have
correctly assembled this product.
Never use any product that has not been maintained or
inspected properly - Your life depends on it!
Replace any and all treestand straps every two years or
when any signs of damage or wear exist before.
Always wear the appropriate footwear when using a
ladder treestand. A good non-slip safety boot is important
to your personal safety. Be especially careful that boot
laces do not get hooked on the stand or any of its
components (tuck shoelaces into boots before climbing).
WARNING
Only use approved RETI parts. Failure to do so may result
in serious injury or death!

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 5
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
- - 7/16”WRENCHES 2
- # 27477
4 MM ALLEN
WRENCH
INCLUDED
1
TOOLS REQUIRED
HARDWARE LIST
Item Part No. Description Image Qty
29 # 23572 YELLOW PLASTIC
WASHER 2 MM 8
30 # 35130 YELLOW CURVED
SPACER 4
31 # 35225 YELLOW CURVED
WASHER 4
32 # 36703 YELLOW PLASTIC
SPACER 12 MM 6
33 # 48042B WING NUT 2
34 # 48057B SCREW WING 2

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
6
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
Item Part No. Description Image Qty
35 # 23603 KNOB SILENT
LADDER 4
36 # 28839 KNOB
M6 X 29 MM 2
37 # 36719 KNOB SILENT
LADDER W/STUD 8
38 # 29712 SQ PLUG 22 MM 1

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 7
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
Item Part No. Description Image Qty
41 # 48679 RUBBER BUMPER
STOP 2
42 # 26813 BOLT M6 X 20 MM 2
43 # 26959 BOLT M6 X 70 MM 1
44 # 48240B BOLT
1/4 X 11/2 IN 7
45 # 48250B BOLT
1/4 X 13/4 IN 4
46 # 48271B BOLT
1/4 X 21/4 IN 2
47 # 48270B BOLT
1/4 X 21/2 IN
14
48 # 48280B BOLT
1/4 X 3 IN 14
49 # 36704 BOLT
1/4 X 31/2 IN 6
50 # 36705 BOLT
1/4 X 4 IN 2
51 # 48752B NUT 1/4 IN 49

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
8
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
ASSEMBLY INSTRUCTIONS
IMPORTANT ASSEMBLY TIP:
Do not tighten any nut and bolt combinations completely
until all parts are assembled together! Finger tighten plus
one turn of a wrench only! This will temporarily hold the
lock- nut on the bolt while helping alignment of all parts!
After all parts are assembled together, all nut and bolt
combinations must be completely tightened.
All assembly must be done in this order at ground
level before uprighting.
Do not remove labels/warnings from product, they are
there for your safety.
Recommended for adult use only.
STEP 1
STEP 2
5
mesh hidden for clarity
6
20
4
51
48
48
6
45
44
23
15
51
1. Attach front, middle, and rear platform sections
(4, 20 and 5) to J-tubes (6) using ten 1/4-20 x 3
IN bolts (48) and nuts (51).
2. Insert bottom tree blade (15) into ends of J-tubes
(6). Slide a strap guide (23) onto each J-tube (6)
and align with rear hole on each side. Secure
parts together using two 1/4-20 x 1-1/2 IN bolts
(44), two 1/4-20 x 1-3/4 IN bolts (45) and nuts
(51).

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 9
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
STEP 3
STEP 4
mesh hidden for clarity
51 17
12
47
3. Attach left and right armrests (10 and 11) to rear
platform section (5) using four 1/4-20 x 3 IN bolts
(48) and nuts (51).
Attach seat support (12) to left and right
armrests (10 and 11) using four 1/4-20 x 3-1/2
IN bolts (49), four 12 MM thick yellow spacers
(32) and nuts (51). The spacers must be placed
between the seat support and armrests. Be sure
to position the seat support with the holes for
the rubber seat bumpers (41) facing up.
Insert the rubber seat bumpers (41) into the
holes in the seat support (12).
4. Attach the top tree blade (17) to the seat support
(12) using two 1/4-20 x 2-1/2 IN bolts (47) and
nuts (51).
12
10
32
5
48
49
51
41
11

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
10
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
STEP 5
STEP 6
51
9
10
11
47
25
44
9
51
7
5. Attach the backrest tubes (9) to the left and right
armrests (10 and 11) using four 1/4-20 x 2-1/2 IN
bolts (47) and nuts (51).
6. Slide the backrest (25) onto the backrest tubes
(9). Attach the backrest spreader (7) to the top of
the backrest tubes (9) using two 1/4-20 x 1-1/2 IN
bolts (44) and nuts (51).

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 11
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
STEP 8
STEP 7
Open tube
mount
VIEW A VIEW B
Turn Counter
Clockwise to
Tension Seat
13
38
51
44
43
14
51
29
32
29
49
7. Thread the M6 x 70 MM bolt (43) all the way into
the seat tensioner (14).
To assemble the seat (13), slide the seat
tensioner (14) through the right seat tube and
into the left seat tube so that the head of the M6
x 70 MM bolt (43) bottoms out on the inside of
the capped seat tube.
Secure the seat tensioner (14) to the seat (13)
using one 1/4-20 x 1-1/2 IN bolt (44) and nut (51).
Insert the 22 MM plug (38) into the end of the
right seat tube.
Using the provided allen wrench, tension the
seat slightly by inserting the wrench through
the hole in the capped seat tube and into the
M6 x 70 MM bolt (43). Turn counter clockwise to
tension the seat. Final desired seat tension can
be done once the seat is assembled onto the rest
of the treestand.
8. Attach the seat assembly to the rest of treestand
using two 1/4-20 x 3-1/2 IN bolts (49), four
yellow washers (29), two 12 MM thick yellow
spacers (32) and nuts (51).

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
12
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
STEP 10
STEP 9
16
44 26
51
42
36
10
11
50 29 30
30
51
9. Assemble the shooting rail (16 and 26) by
inserting the small diameter tube of adjustable
shooting rail parts (26) into the shooting rail (16).
Align the holes and secure together using two
1/4-20 x 1-1/2 IN bolts (44) and nuts (51).
10. Attach the shooting rail assembly to the rest of
the treestand using two 1/4-20 x 4 IN bolts (50),
two yellow washers (29), four curved yellow
spacers (30) and nuts (51).
Attach the shooting rail adjustment knobs (36)
to the adjustment plates on the left and right
armrests (10 and 11) using two M6 x 20 MM bolts
(42).

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 13
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
STEP 11
mesh hidden for clarity
4
8
51
29
31
31
47
11. Attach the footrest (8) to the front platform
section (4) using two 1/4-20 x 2-1/2 IN bolts (47),
two yellow washers (29), four curved yellow
washers (31) and nuts (51).

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
14
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
STEP 12
mesh hidden for clarity
DETAIL A
DETAIL B
51
47
23
47
19
18
51
6
51
2
23
51
47
12. Slide the top ladder section (2) into the pockets
on the J-tubes (6) and secure using two 1/4-20 x
1-3/4 IN bolts (45) and nuts (51).
Pre-assemble the platform braces (19) with the
ladder hand rails (18) by inserting one end of
each platform brace (19) into the lower end of
each ladder hand rail (18) and aligning the holes.
Then, attach the pre-assembled platform braces
(19) and ladder hand rails (18) and four strap
guides (23) to the rest of the treestand using six
1/4-20 x 2-1/2 IN bolts (47) and nuts (51). Pay
close attention to DETAIL A and DETAIL B for
proper positioning of strap guides (23).
45

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 15
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
14. Ladder sections are assembled on the ground in
the following order: bottom ladder section (3),
ladder section with stabilizer bar mount (21), two
middle ladders sections (1) and the top ladder
section (2) with the treestand top assembly.
The ladder sections are secured together with
two dierent types of knobs, Silent LadderLock
(35) and Silent LadderLock with stud (37). The
four Silent LadderLocks (35) are used for the
center pocket on each section. The eight Silent
LadderLocks with stud (37) are used for the two
outside pockets on each section.
STEP 13
51
28
21
46
13. Attach the ladder ratchets (28) to the ladder
section with the stabilizer bar mount (21) using
two 1/4-20 x 2-1/4 IN bolts (46) and nuts (51). Set
aside for now.
STEP 14
2
37
35
1
1
21
3

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
16
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
FIGURE 1
15. Before uprighting the stand to the tree, you must
attach the two long straps (55) to the assembled
treestand. Begin by feeding one end of each
strap through the three strap guides (23) under
the platform and at the top of the ladder on both
sides. SEE FIGURE 1 and DETAIL A.
Attach the looped ends of the straps together
near the center of the ladder with the carabiner
on the end of the tether rope (56). SEE FIGURE 1
and DETAIL B.
Run the opposite end of each strap down to the
ladder ratchet (28) on either side of the ladder.
Run the strap down through the center slot in
the ratchet and“ratchet” just enough to loosely
hold the strap in place. They do not need to be
tight. This is only temporary to keep them out of
the way while you upright the stand to the tree.
SEE FIGURE 1 and DETAIL C.
Lastly, run the tether rope (56) down the
length of the ladder, wrap around the Silent
LadderLocks (35 and 37) that are near the ladder
ratchets (28) and loosely tie in place. SEE FIGURE
1 and DETAIL C. You are now ready to upright
the ladder. Follow setup and use instructions on
following pages.
DETAIL B
DETAIL C
55
23
23
23
56
28
37
35
Carabiner
DETAIL A

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 17
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
READ AND UNDERSTAND THE FOLLOWING WARNINGS BEFORE SETUP AND USE
STOP
WARNING
Bring ratchet strap(s) up with you in a pocket - Do Not
carry in your hands!
WARNING
Double check assembly steps to be certain you have
correctly assembled this product.
Study your new stand to become familiar with all of its
features and design. At ground level, following provided
use instructions, practice attaching stand to tree and
removing stand from tree. Practice sitting, standing, and
using this product before attaching overhead. Save these
instructions for future reference. You must always use the
provided Fall Arrest System (FAS) while using this product.
Always use at least three (3) people to install or take down
a ladder treestand. Always have two people stabilize the
ladder before climbing to the platform the rst time after
every set-up.
Be absolutely sure the tree blade(s) on stand and the
stabilizer bar are contacting tree before climbing ladder.
Stabilizer bar must always be correctly and securely
attached to ladder and tree before climbing ladder.
Make sure ladder bottom is rmly seated on dry, level
ground. Attach your harness tether to the tree before
securing the platform to the tree and stepping onto
platform. Refer to the Full Body Harness instructions.
Never ascend or descend ladder without straps/ropes
securely holding ladder to tree and stabilizer bar securely
attached. Failure to correctly perform these steps can
cause the ladder to collapse/buckle-over backwards
during the initial ascent to attach ratchet strap resulting
in serious injury or death.
Always lean forward as you climb and attach your harness
to the tree before securing the platform to the tree with
the provided ratchet straps.
WARNING
Always maintain three (3) points of contact when
climbing a ladder treestand. Proper three-point contact
means having either two feet with one hand or one foot
with two hands on the step portion of the ladder or
climbing aid at all times.
Always wear the appropriate footwear when using a
ladder treestand. A good non-slip safety boot is important
to your personal safety. Be especially careful that boot laces
do not get hooked on the stand or any of its components
(tuck shoelaces into boots before climbing).
Never stand on seat, it is designed for sitting only.
Do Not allow excessive strap buildup in ratchet as this
will prevent the ratchet teeth from engaging causing
slippage.
Always attach ratchet straps securely while using this
product!
If seat is removable, be certain it is securely attached
when in use.
Some models include a shooting rail. Never lean against,
lean over, or sit on shooting rail. It is designed as a
shooting rest only. Always be aware that the shooting rail
can swing to one side or pivot up and down.
Some models include a footrest, which is designed as a
footrest only. Never stand on footrest! Always be fully
aware of foot placement.
Some models include a multi-piece stabilizer bar system.
Be sure attachment hardware goes through all extension
tubes of the stabilizer bar.

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
18
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
SET UP AND USE INSTRUCTIONS
During installation and removal of ladder treestands,
you must always and properly use the included Full Body
Harness (Fall Arrest System). Refer to the Full Body Harness
instructions included with this product for proper use.
WARNING
Never use a treestand on a dead, leaning, diseased or
loose barked tree, or a utility pole. Always avoid electrical
power lines.
Bring ratchet strap(s) up with you in a pocket - Do not
carry in your hands!
WATCH THE SET-UP AND USE VIDEO ONLINE AT
WWW.HUNTRIVERSEDGE.COM
TO ASSIST WITH THE SET-UP OF YOUR TREESTAND
1. Select a straight, healthy tree. Do Not attempt to install on a tree
that is not healthy.
2. Place the assembled product lying on the ground in front of the
tree with the bottom ladder section approximately ve feet away
from the base of the tree.
3. Position one person at bottom end of ladder. This person has to
prevent the ladder end from tilting up and from skidding across
the ground when platform end is lifted.
4. Position two people at the platform end of the ladder, lift the
platform end and continue uprighting by walking toward bottom
end of ladder while moving hands along ladder rails. Stand ladder
up against chosen tree on dry, level ground. Use caution when
ladder comes over center against the tree, as shown by arrow “A”.
SEE FIGURE 2.
5. Once elevated completely, carefully slide the base so that the
sitting and standing platforms are parallel to the ground, as
shown by arrow“B”. SEE FIGURE 2.
6. Step back and look at the ladder top to see that both the lower
platform tree blade and upper tree blade are contacting the tree.
Adjust as needed so both of the tree blades are contacting the
tree.
7. Step down hard on bottom step to push ladder legs into the
ground, as shown by arrow “C”. SEE FIGURE 2.
8. While two people hold the stand in place, the third person should
complete the necessary steps on following pages to secure the
stand to the tree.
A
A
C
B
FIGURE 2

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5 19
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
9. Begin by removing the long straps (55) from the ground level
ratchets (28) and let them hang down on either side of the tree.
SEE FIGURE 3.
10. Hook the large carabiner (57) to one of the long straps (55) that
are hanging down near the tree. SEE FIGURE 3. If the tree has
branches between the ground and the top of the stand,
proceed to the next step. If the tree is free of branches
between the ground and the top of the stand, skip ahead to
STEP 12.
FIGURE 3
55
57
55

Check for parts online at www.HuntRiversEdge.com or call 800-345-6007 M-F 8-5
20
Operator's Manual
LOCKDOWN 21-FT WIDE Ladder Stand
11. If the tree has branches between the ground and the top of the
stand, before hooking the two long straps (55) together behind
the tree with the carabiner (57), you must rst get both straps
on the same side of all of the branches. To do so, simply use the
telescoping stabilizer bar (22) to lift up and drop the strap that
has the carabiner hooked to it over the branches.
a. Hook the carabiner onto the end of the stabilizer bar as shown
in FIGURE 4.
b. Then lift up and drop over each branch. The weight of the
carabiner will drop the strap back down to ground level after
each branch you drop it over.
c. Repeat dropping it over the branches until both straps are on
the same side of all of the branches. SEE FIGURE 5. Then there
will be a clear path for the straps and carabiner to rise up the back
of the tree, all the way to the top of the stand.
FIGURE 5
FIGURE 4
57
55
22
22
57
55