TRIBU SENJA User manual

SENJA SOFA
ASSEMBLY INSTRUCTIONS
SESO01 - 22-11-2018

COMPONENTS
FRAME
Regular / Deep
Components for back- and armrest:
LEG
alu / teak
CONNECTION
ARMREST / BACKREST
High / Low
Regular / Deep
CLAMP
CONSOLE TABLE
lava stone / teak
SUPPORT HIGH LEGS
Components for the console table:

COMPONENTS
SIDE TABLE
lava stone / teak
TABLE LEG
TABLE SUPPORT
Components for the side table:
Components for the table:
Hardware:
LARGE SCREW
countersunk
BUTTON SCREW
buttonhead
WOOD SCREW
SMALL SCREW
countersunk
FLAT SCREW
flathead
TABLE
lava stone / teak
WASHER

ASSEMBLY INSTRUCTIONS
Put the FRAME upside down on a protective cover. Attach the LEGS to the
frame by turning them clockwise. Repeat this step for each FRAME.
Use 2 LARGE SCREW to mount 2 CLAMPS to each ARM/BACKREST
provided. To secure the CLAMPS to the ARM/BACKRESTturn the LARGE
SCREWS clockwise and tighten for 90%.
1
2

If you only have 1 FRAME proceed to step 4. If you have multiple FRAMES
put them in the desired position. Once they are in the correct position
attach them to each other with the connector. To secure the CONNECTION
put 2 SMALL SCREWS in the designated holes and turn them clockwise.
Remove the headless plastic screws that cover the holes.
3
4

Put the CLAMPS on the frame in a way the hole of the CLAMP and the
frame align. Once aligned, secure the CLAMP by inserting a SMALL
SCREW and turning it clockwise. Repeat for the other CLAMP.
5
Tighten the BIG SCREWS 100%
6

Repeat steps 5 + 6 for each individual arm/backrest.
7
If your Senja sofa has the following components, continue to the corresponding
step.
Side table: step
Table: step
Console table: step
If you don’t have any of these components, proceed to step
14
8
9
12
19

Mount the SIDE TABLE on top of the TABLE LEG by using 4 BUTTON
SCREWS. Turn clockwise to tighten.
9
To mount the assembled SIDE TABLE to the FRAME remove the headless
plastic screws in the FRAME there where you want your SIDE TABLE.
10

To secure the assembled SIDE TABLE to the frame, allign the hole in the
CLAMP and the hole in the FRAME. Use a SMALL SCREW and tighten it by
turning it clockwise.
11
To install a TABLE, you need to install 2 SUPPORTS first. Remove headless
screws first. To attach the TABLE SUPPORTS to the FRAME use 2 SMALL
SCREWS per TABLE SUPPORT. Tighten them by turning them clockwise.
12

Place the TABLE on top of the TABLE SUPPORT. If it is a TEAK table use 4
WOOD SCREWS, if it is a LAVE STONE table use 4 BUTTON SCREWS. To
secure the table turn the screws clockwise.
13

To install a CONSOLE TABLE, you need to install the HIGH LEGS + SUP
PORT first.To attach the HIGH LEGS to the FRAME make sure there are only
2 LEGS attached to the FRAME. Slide the HIGH LEGS under the frame.
Make sure the hole in the HIGH LEGS which is the farthest from the post
aligns with the holes in the center of the FRAME.
14
15

To secure the HIGH LEGS to the FRAME use 2 LONG SCREWS and 2
WASHERS per HIGH LEG. Slide the FLAT SCREWS through the WASHERS
and into the designated holes. Turn them clockwise to tighten.
Place the SUPPORT on top of the HIGH LEGS, make sure the hole in the
SUPPORT aligns with the hole in the HIGH LEGS. Use a LARGE SCREW to
secure the SUPPORT to the HIGH LEGS.
16
17

Carefully place the CONSOLE TABLE on top of the SUPPORT, align the
holes in the CONSOLE TABLE with the holes in the SUPPORT. Use 4 BUT-
TON SCREWS to secure them together.
18

Place the seat cushion in position by alligning the edge of the seat cushion
with the edge of the frame.
19
To fix the cushion into place, attach the velcro strips to each other. Make
sure that the velcro straps are on the front side of the sofa.
20

Slide the cushions over the ARM/BACKREST. Make sure the letter on the
label (inside of the pillow) matches the letter on the arm/backrest. The label
must always be on the outside of the sofa.
21

Tribù nv
Oude Heidestraat 72
3740 Bilzen
BELGIUM
www.tribu.com
[email protected]