Vertex Standard EVX-534 User manual
EVX-534
Operating Manual
prOgraMMable FunctiOns/Features
IP57Submersible(1m/30min.)
9ProgrammableFunctionKeys
2-ToneEncode/Decodeø1
5-ToneEncode/Decodeø1
MDC-1200®Encode/Decodeø1
Scan
GroupScan
DualWatch
FM-Scan(Follow-MeScan)
TAScan
Encryptionø1
Privacyø2
VOX
TalkAround
Emergency
LoneWorker
TXSaveDisable
DirectChannelEntry
CodeUp/Downø1
CodeSetø1
SpeedDialø1
DTMFCodeSetø1
IDCheckø1
ARTSTMø1/ARTS
II
TM
(AutoRangeTranspondSystem)
ø1:Analogmodeonly
ø2:Digitalmodeonly
EVX-534
AB C D
FCC ID: AXI11153020
IC: 10239A-11153020
BatteryPackInstallationandRemoval...............4
BatteryCharging..................................................4
LowBatteryIndication........................................5
BeltClipInstallationandRemoval.....................6
MIC/SPCapInstallation......................................6
PreliminarySteps.................................................9
OperationQuickStart..........................................9
AutomaticTime-OutTimer...............................12
ProgrammableKeyFunctions..........................13
DescriptionofOperatingFunctions.................16
cOntents
Younowhaveatyourngertipsavaluablecommunicationstool,aVertexStandardtwo-wayradio!Rugged,reliable
andeasytouse,yourVertexStandardradiowillkeepyouinconstanttouchwithyourcolleaguesforyearstocome,
withnegligiblemaintenancedown-time.Pleasetakeafewminutestoreadthismanualcarefully.Theinformation
presentedherewillallowyoutoderivemaximumperformancefromyourradio,incasequestionsariselateron.
r Therearenoowner-serviceablepartsinsidetheradio.Allservicejobsmustbereferredtoanauthorized
VertexStandardServiceRepresentative.
r Inordertomaintainthespeciedwaterintegrityperformance,periodicmaintenanceisrecommended.
r Shouldtheradiosustainasevereshock(e.g.ifitisdropped),thewaterintegritymaybecompromised,
requiringservice.Shouldthisoccur,contactyourAuthorizedVertexStandardDealer.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual 1
Important Notice for North American Users Regarding 406 MHz Guard Band
The U.S. Coast Guard and National Oceanographic and Atmospheric Administration have requested the
cooperation of the U.S. Federal Communications Commission in preserving the integrity of the protected
frequency range 406.0 to 406.1 MHz, which is reserved for use by distress beacons. Do not attempt to pro-
gram this apparatus, under any circumstances, for operation in the frequency range 406.0 - 406.1 MHz if
the apparatus is to be used in or near North America.
Warning - Frequency band 406 - 406.1 MHz is reserved for use ONLY as a distress beacon by the US Coast
Guard and NOAA. Under no circumstance should this frequency band be part of the pre programmed oper-
ating frequencies of this radio.
IntroductIon
The EVX-534 is full-featured Hand-Held Digital/Analog Transceiver designed for business communications in the
VHF/UHF Land Mobile bands. This transceiver is designed for reliable business communications in a wide variety
of applications with a wide range of operating capability provided by their leading-edge design.
The EVX-534 allows to 512-channel capacity and 32 groups which can each be programmed with an 8-character
Alpha-Numeric Tag.
Important channel frequency data is stored in the ash memory on the CPU, and is easily programmable by a Ver-
tex Standard licensed dealers using a personal computer with Vertex Standard Programming equipment: FIF-12
USB Programming Interface, and CT-106 Connection cable with CE142 Software. Or, once a single radio is pro-
grammed, cloning cable CT-27 can be used to program additional radios directly.
The pages which follow will detail the many advanced features provided in the EVX-534 transceiver. After reading
this manual, you may wish to consult with your Network Administrator regarding precise details of the congura-
tion of this equipment for use in your application.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
2
WarnIng! Fcc rF ExposurE rEquIrEmEnts
This Radio has been tested and complies with the Federal Communications Commission (FCC) RF exposure limits
for Occupational Use/Controlled exposure environment. In addition, it complies with the following Standards and
Guidelines:
FCC 96-326, Guidelines for Evaluating the Environmental Effects of Radio-Frequency Radiation.
FCC OET Bulletin 65 Edition 97-01 (2001) Supplement C, Evaluating Compliance with FCC Guidelines for
Human Exposure to Radio Frequency Electromagnetic Fields.
ANSI/IEEE C95.1-1992, IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequen-
cy Electromagnetic Fields, 3 kHz to 300 GHz.
ANSI/IEEE C95.3-1992, IEEE Recommended Practice for the Measurement of Potentially Hazardous Electro-
magnetic Fields - RF and Microwave.
WARNING:
This radio generates RF electromagnetic energy during transmit mode. This radio is designed for and clas-
sied as Occupational Use Only, meaning it must be used only during the course of employment by indi-
viduals aware of the hazards, and the ways to minimize such hazards. This radio is not intended for use by
the General Population in an uncontrolled environment.
CAUTION:
To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupa-
tional use, always adhere to the following guidelines:
This radio is NOT approved for use by the general population in an uncontrolled exposure environment.
This radio is restricted to occupational use, work related operations only where the radio operator must
have the knowledge to control his or her RF exposure conditions.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
3
WarnIng! Fcc rF ExposurE rEquIrEmEnts
When transmitting, hold the radio in a vertical position with its microphone 2 inches (5 cm) away from
your mouth and keep the antenna at least 2 inches (5 cm) away from your head and body.
The radio must be used with a maximum operating duty cycle not exceeding 50%, in typical Push-to-
Talk congurations.
DO NOT transmit for more than 50% of total radio use time (50% duty cycle). Transmitting more than
50% of the time can cause FCC RF exposure compliance requirements to be exceeded. To keep the Body
Worn conguration with the Vertex Standard CLIP-20 belt-clip, reduce the maximum operating duty
cycle still more.
The radio is transmitting when the red LED on the top of the radio is illuminated. You can cause the ra-
dio to transmit by pressing the P-T-T button.
SAR compliance for body-worn use was only demonstrated for the specic belt-clip (CLIP-20). Other
body-worn accessories or congurations may NOT comply with the FCC RF exposure requirements and
should be avoided.
When operate the radio with the Vertex Standard CLIP-20 belt-clip, make the transmission time as short
as possible, to keep the Body Worn conguration.
Always use Vertex Standard authorized accessories.
The information listed above provides the user with the information needed to make him or her aware of
RF exposure, and what to do to assure that this radio operates with the FCC RF exposure limits of this
radio.
Electromagnetic Interference/Compatibility
During transmissions, this radio generates RF energy that can possibly cause interference with other de-
vices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so.
Do not operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals,
health care facilities, aircraft, and blasting sites.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
4
BEForE You BEgIn
To remove the battery, turn the radio off and re-
move any protective cases. Slide the Battery Pack
Latch on the bottom of the radio toward the front
panel while sliding the battery down about 1/2
inch (1.5 cm). Then lift the battery out from the
radio.
Do not attempt to open any of the re-
chargeable Lithium-Ion packs, as they
could explode if accidentally short-circuited.
Battery Pack Installation and Removal
To install the battery pack, align the battery pack
to the radio with an offset about 1/2 inch (1.5 cm)
from the top edge of battery compartment, then
slide the battery pack upward until it locks in
place with a “Click.”
Battery Charging
Remove the Spacer Plate from the nest of the
optional CD-58 Desktop Charger, if the Battery
Spacer is installed.
Insert the DC plug from the optional PA-55 AC
Adapter into the DC jack on the rear panel of the
optional CD-58 Desktop Charger, and then con-
nect the PA-55 AC Adapter to the AC line outlet.
Insert the battery pack into the CD-58 Desktop
Charger while aligning the slots of the battery
pack with the guides in the nest of the CD-58;
refer to the following illustration for details on
PA-55
CD-58
Spacer Plate AC Line Outlet
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
5
BEForE You BEgIn
proper positioning of the battery pack. If charging
with the transceiver attached, turn the transceiver
off. The antenna jack should be at the left side
when viewing the charger from the front.
If the battery pack is inserted correctly, the LED
indicator will glow red. A fully-discharged battery
pack will charge completely in 1.5 - 3.0 hours
(depending on the battery pack being charged).
When charging is completed, the LED indicator
will change to green.
Disconnect the battery pack from the CD-58
Desktop Charger and unplug the PA-55 AC
Adapter from the AC line outlet.
1) Always use the Vertex Standard FNB-
V133LI-UNI or FNB-V134LI-UNI Lithi-
um-Ion Battery Pack.
2) Use only the Vertex Standard CD-58 Desktop
Charger and the Vertex Standard PA-55 AC Adapter.
3) To reduce the risk of explosion, recharge the bat-
teries outside of hazardous locations.
4) Perform the battery charging where the ambient
temperature range +41 °F to +104 °F (+5 °C to +40
°C). Charge out of this range could cause damage
to the battery pack.
5) Battery Pack shall not be exposed to excessive
heat such as sunshine, re, or the like.
6) Risk of explosion if battery is replaced by an in-
correct type. Dispose of used batteries according to
the instructions
7) For further details and cautions of the charging,
refer to the Operating Manual of the CD-58 Desk-
top Charger.
Low Battery Indication
As the battery discharges during use, the voltage
gradually becomes lower. When the battery voltage
becomes to low, substitute a freshly charged battery
and recharge the depleted pack. The LED indicator
on the top of the radio will blink red when the battery
voltage is low.
CAUTION
Danger of explosion if battery is replaced
with an incorrect battery. Replace only with
the same or equivalent type.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
6
Belt Clip Installation and Removal
BEForE You BEgIn
To install the Belt Clip: align
the Belt Clip to the groove of
the Battery pack, then press
the Belt Clip downward until it
locks in place with a “Click.”
Belt Clip Tab
To remove the Belt Clip: use a
at head screw driver to press
the Belt Clip Tab away from
the battery pack to unlock the
Belt Clip, then slide the Belt
Clip upward to remove it.
MIC/SP CAP Installation
Install the MIC/SP cap with the
supplied screws.
Use only the supplied screws
when install the MIC/SP cap.
This radio does not keep the
submersible Rating (IP57: 1
meter / 30 minutes) when the
MIC/SP cap is not installed
in the MIC/SP jack.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
7
notE
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
8
EVX-534
AB C D
PTT Switch
SIDE-1 Button
SIDE-2 Button
MIC/SP Jack
(External MIC/SP)
Speaker Microphone
Antenna Jack
TOP SEL (Top Select) Key
CH (Channel) Selector
VOL (Volume)/PWR (Power) Knob
Battery Pack Latch
controls & connEctors
LCD (Liquid Crystal Display) 4-Button Programmable Key
LED Indicator (Programmable)
Default settings are:
Steady Red: Transmitting in progress (Analog)
Steady Blue: Transmitting in progress (Digital)
Blinking Green: Busy Channel
Steady Green: Tone Squelch in defeated condition
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
9
lcd Icons & IndIcators
Group Number
RSSI Indicator (four steps)
“Privacy” or “Encryption”
is activated
Option SW (Key Function)
is activated
Low Transmit Power Mode “On”
“Audio Compander” is activated
“CALL” Indicator
Receiver Monitor
“Talk-Around” is enabled
Battery Indicator
“Group Scan” is enabled
Priority-2 Channel
“Dual Watch” is activated
: “Scan” is enabled
: “Priority Scan” is activated
8-character
Alpha-numeric Display
“VOX” is activated
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
10
opEratIon
Preliminary Steps
Install a charged battery pack onto the transceiver,
as described previously.
Screw the supplied antenna
onto the Antenna jack.
It is not recommended to op-
erate this transceiver without
an antenna connected.
If you have a Speaker/Mi-
crophone, we recommend
that it not be connected un-
til you are familiar with the basic operation of the
EVX-534. Refer to page 11 for more information
about Speaker/Microphone usage.
IMPORTANT NOTE
Water resistance of the transceiver (IP57: 1
meter / 30 minutes) is assured only when the
following conditions:
Battery pack is attached to the transceiver;
Antenna is connected to the antenna jack;
and MIC/SP cap is installed in the MIC/
SP jack.
Use of a speaker microphone in the acces-
sory connector negates the IP57 rating.
Operation Quick Start
Tu r n the t o p pa n e l ’s
VOL/PWR knob clock-
wise to turn the radio
on.
Turn the top panel’s CH
Selector knob to choose
the desired operating
channel. A channel name
will appear on the LCD.
The radio announces the
channel number, if the Channel Announcement
Feature is enabled via the clone editor software.
If you want to select the operating channel from a
different Channel Group, press (or press and hold)
the Programmable key (assigned to the “group
up/doWn” function) to change desired Channel
Group before selecting the operating channel.
Note: Some models are programmed so that the
operating channels are selected by the Program-
mable key and the Channel Group is selected by
the CH Selector knob.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
11
opEratIon
Rotate the VOL/PWR
knob to set the volume
le vel . I f no sign al is
present on the analog
channel, press and hold
in the SIDE-1 button
(under the PTT switch)
more than 2 seconds;
background noise will
now be heard, and you
may use this to set the
VOL/PWR knob for the
desired audio level. Press and hold the SIDE-1
button more than 2 seconds (or press the SIDE-1
button twice) to quiet the noise and resume nor-
mal (quiet) monitoring.
To transmit, monitor the
channel and make sure it
is clear.
Press and hold the PTT
switch. Speak into the
microphone area of the
front panel grille in a normal voice level. To re-
turn to the Receive mode, release the PTT switch.
Press the (Orange) TOP
SEL key, SIDE-2 but-
ton, or front panel’s pro-
grammable keypad ([A],
[B], [C] and [D] keys)
to activate one of the
pre-programmed func-
tions which may have
been enabled at the time
of programming by the
dealer. See the next sec-
tion for details regarding
feature availability for
this radio.
If a Speaker/Micro-
phone is available,
remove the plastic cap
and its two mounting
screws from the right
side of the transceiver,
then align the connector
EVX-534
AB C D
D
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
12
of the Speaker/Microphone on the radio; secure
the connector pin using the screws supplied with
the Speaker/Microphone. Hold the speaker grille
up next to your ear while receiving. To transmit,
press the PTT switch on the Speaker/Microphone,
just as you would on the main transceiver’s body,
and speak into the microphone on a normal voice
level.
Note 1): Save the original plastic cap and its
mounting screws. They should be reinstalled
when not using the Speaker/Microphone.
2) When you press the PTT switch on the Speak-
er/Microphone, it disables the internal micro-
phone, and vice versa.
If the BCLO (Busy Channel Lockout) feature
has been programmed on an analog channel, the
radio will not transmit when a carrier is present.
Instead, the radio will generate short beep three
times. Release the PTT switch and wait for the
channel to be clear of activity.
If the BTLO (Busy Tone Lockout) feature has
been programmed on an analog channel or
CCLO (Color Code Lockout) feature has been
programmed on a digital channel, the radio
opEratIon
can transmit only when there is no carrier be-
ing received or when the carrier being received
includes the correct tone (CTCSS tone or DCS
code) on an analog channel or correct code on a
digital channel.
Automatic Time-Out Timer
If the selected channel has been programmed for au-
tomatic time-out, you must limit the length of each
transmission. While transmitting, a beep will sound
10 seconds before time-out. Another beep will sound
just before the deadline; the top panel’s red LED (“TX”
indicator) will disappear and transmission will cease
soon thereafter. To resume transmitting, you must re-
lease the PTT switch and wait for the “penalty timer”
to expire.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
13
advancEd opEratIon
Programmable Key Functions
The EVX-534 provides the seven programmable
function (PF) keys: TOP SEL, SIDE-1, SIDE-2,
[A], [B], [C] and [D] keys. These PF keys can be
customized, via programming by your Vertex Stan-
dard dealer, to meet your communications/network
requirements.
The possible PF key programming features are il-
lustrated on the next page, and their functions are
explained beginning after page 16. For further details,
contact your Vertex Standard dealer.
In this chapter, the following icons are used to indi-
cate features supported in either the “Analog” mode
or “Digital” mode:
: Indicates a “Analog” mode only feature.
: Indicates a “Digital” mode only feature.
For features that are available in both “Analog” and
“Digital” modes, no icon is shown.
For future reference, check the box next to each func-
tion that has been assigned to the PF key on your
particular radio, and keep it handy.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
14
advancEd opEratIon
FunctIon
programmaBlE KEY (prEss KEY / prEss and Hold KEY)
TOP SEL SIDE-1 SIDE-2 [A] [B] [C] [D]
None / / / / / / /
Monitor / / / / / / /
Monitor -Momentarily- /--- /--- /--- /--- /--- /--- /---
Light / / / / / / /
Low Power / / / / / / /
Privacy / Encryption / / / / / / /
SET / / / / / / /
SQL OFF / / / / / / /
SQL OFF -Momentarily- /--- /--- /--- /--- /--- /--- /---
SQL Set / / / / / / /
Beep Off / / / / / / /
AF Min Volume / / / / / / /
CH Announcement / / / / / / /
Whisper / / / / / / /
VOX / / / / / / /
VOX Set / / / / / / /
VOX Anti-Trip / / / / / / /
Emergency /--- /--- /--- /--- /--- /--- /---
Lone Worker / / / / / / /
Group Up / / / / / / /
Group Down / / / / / / /
Channel Up / / / / / / /
Channel Down / / / / / / /
Speed Channel Up --- / --- / --- / --- / --- / --- / --- /
Speed Channel Down --- / --- / --- / --- / --- / --- / --- /
RPI-2 Set / / / / / / /
PRI-2 Disable / / / / / / /
PRI-2 / / / / / / /
Direct CH 1 / / / / / / /
Direct CH 2 / / / / / / /
Direct CH 3 / / / / / / /
Direct CH 4 / / / / / / /
Direct CH Entry / / / / / / /
Scan / / / / / / /
Group Scan / / / / / / /
Dual Watch / / / / / / /
FM-Scan / / / / / / /
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
15
advancEd opEratIon
FunctIon
programmaBlE KEY (prEss KEY / prEss and Hold KEY)
TOP SEL SIDE-1 SIDE-2 [A] [B] [C] [D]
Scan Set / / / / / / /
Group Scan Set / / / / / / /
TA Scan / / / / / / /
Talk Around / / / / / / /
Reset / / / / / / /
Call 1 / / / / / / /
Call 2 / / / / / / /
Call 3 / / / / / / /
Call 4 / / / / / / /
Call 5 / / / / / / /
Code Up / / / / / / /
Code Down / / / / / / /
Code Set / / / / / / /
Speed Dial / / / / / / /
Call / / / / / / /
Status Set / / / / / / /
Status Up / / / / / / /
Status Down / / / / / / /
Status Check / / / / / / /
Duty / / / / / / /
ID Check / / / / / / /
ARTS Login / / / / / / /
TX Save Disable / / / / / / /
Lock / / / / / / /
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
16
advancEd opEratIon
Description of Operating Functions
prIvacY
Press, (or press and hold), the assigned PF key to
toggle the Privacy feature “On” and “Off”. The Pri-
vacy feature initiates an encryption algorithm that
will protect your communication from unauthorized
eavesdropping.
When the Privacy feature is activated, the “ ” icon
will be indicated on the display.
EncrYptIon
When the Voice Scrambler feature is enabled, press,
(or press and hold), the assigned PF key to toggle the
Voice Encryption “On” and “Off”.
When the Voice Scrambler is activated, the “ ” icon
will be indicated on the display.
sEt
Press, (or press and hold), the assigned PF key to ac-
tivate the “User Set (Menu)” mode. See page 29 for
more information of the “User Set (Menu)” mode.
monItor
Press, (or press and hold), the assigned PF key to
cancel any signaling features; the LED indicator
will glow with a pre-dened color (Factory default:
green).
monItor -momEntarIlY-
Cancel any signaling features while pressing the as-
signed PF key.
lIgHt
Press, (or press and hold), the assigned PF key to
toggle the back light of the display and keypad “On”
and “Off”.
loW poWEr
Press, (or press and hold), the assigned PF key to
set the radio’s transmitter to the “Low Power” mode,
thus extending battery life. Press, (or press and hold),
the key again to return to “Normal” transmit power
when in difcult terrain.
When the radio’s transmitter is set to “Low Power”
mode, the “L” icon will be indicated on the display.
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
17
advancEd opEratIon
sql oFF
Press, (or press and hold), the assigned PF key to open
the SQL to hear background noise (unmute the audio).
sql oFF -momEntarIlY-
Opens the SQL to hear background noise (unmute the
audio) while pressing the assigned PF key.
sql sEt
You can manually adjust the squelch level using this
function:
Press, (or press and hold), the assigned PF key. A
tone will sound, and the current squelch level will
appear on the display.
Press the SIDE-1/SIDE-2 buttons (or [A]/[B]
keys) to select the desired squelch level. Available
selections are “SQLLV OP (Open)”, “SQLLV
TH (Threshold)”, “SQLLV NM (Normal)” and
“SQLLV TI (Tight)”.
Press the [D] key to store the new setting. The
display indicates “- SET -” briey, then reverts to
the normal channel indication.
You may cancel the new setting by pressing the
[C] key. In this case, the display indicates “-
CANCEL -” briey.
BEEp oFF
Press, (or press and hold), the assigned PF key, the
display indicates “BEEP OFF” briefly, and disable
the radio beeps and the channel announcement (if ac-
tivated) temporarily. Again press, (or press and hold),
the assigned PF key, the display indicates “BEEP
ON” briey, and enable the radio beeps and the chan-
nel announcement.
aF mInImum volumE
Press, (or press and hold), the assigned PF key to
reduce the audio output to the (lower) level pro-
grammed by your Vertex Standard dealer.
cH announcEmEnt
Press, (or press and hold), the assigned PF key to se-
lect the channel change conrmation between “beep”
(indicates “BEEP” briey) and “announcement” (in-
dicates “ANNOUNCE” briey).
FCC ID: AXI11153020
IC: 10239A-11153020
EVX-534 OpErating Manual
18
advancEd opEratIon
WHIspEr
Press, (or press and hold), the assigned PF key, the
display indicates “WHISP ON” briey, and increase
the microphone gain; thus you can speak in a low
voice (whisper) temporarily. Press again, (or press
and hold again), the assigned PF key, the display
indicates “WHISP OFF” briey, and resume normal
microphone gain.
vox
Press, (or press and hold), the assigned PF key, the
display indicates “VOX O.N” briey, and activates
the VOX function; allowing hands-free, automatic
activation of the transmitter, based on voice input into
the microphone. When the VOX function is activated,
a small dot (“.”) will be indicated at the bottom right
of the display. You may disable the VOX function
temporarily by pressing the PTT switch.
Press again, (or press and hold again), the assigned
PF key, the display indicates “VOX OFF” briefly,
and resume normal operation.
vox antI-trIp
Press, (or press and hold), the assigned PF key to
toggle the VOX Anti-Trip feature “On” and “Off”.
When the VOX Anti-Trip feature is set to “On”, the
display indicates “ATRP ON” briey, and the trans-
ceiver does not activate the transmitter section from
the receiver audio or own beep sound. Press again,
(or press and hold again), the assigned PF key, the
display indicates “ATRP OFF” briey, and the VOX
Anti-Trip feature is disabled.
EmErgEncY
The EVX-534 includes an “Emergency” feature in
either analog or digital modes, which may be useful
for alerting another party monitoring on the same fre-
quency as your transceiver’s channel.
Press the assigned PF key, the “- EMG -” indication
will be indicated on the display, and initiate an emer-
gency call on the pre-defined channel. For further
details contact your Vertex Standard dealer. To revive
the radio from the Emergency mode, just press again
the assigned PF key or turn off the radio.
FCC ID: AXI11153020
IC: 10239A-11153020
Other manuals for EVX-534
2
Table of contents
