Vivo STAND-SIT1L User manual

Sit to Stand Single Monitor & Laptop Wall Mount
Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1l
SKU: STAND-SIT1L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
OPTION A: Wood Stud Mounting
Install Cover (G) onto top and bottom of Mount
(C). Use a stud finder and determine your desired
mounting location. Hold Mount (C) up to the wall
and mark the mounting hole locations. Use of a
level is highly recommended. Drill 1.2” (30mm)
deep holes using a ⅛” (3mm) drill bit. Install Mount
(C) to the wall using M6x50mm Screws (W-A) and a
Phillips screwdriver.
Remove protective film from Pads (F) and apply them to Laptop Tray (E).
PACKAGE CONTENTS
TOOLS NEEDED
13.2lbs
(6.6kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Upper Arm
B(x1)
Lower Arm
C (x1)
Mount
S-B (x3)
Screw Cap
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Arm
Extension
E(x1)
Laptop Tray
F(x4)
Pad
M-A (x8)
M4x12mm
Screw
S-A (x3)
M6x25mm
Spring Screw
T-A (x1)
3mm Allen
Wrench
T-B (x1)
5mm Allen
Wrench
W-B (x3)
Concrete
Anchor
W-A (x3)
M6x50mm
Screw
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
STEP 1
OPTION B: Concrete Wall Mounting
Install Cover (G) onto top and bottom of Mount
(C).Hold Mount (C) up to your desired position
and mark mounting hole locations. Use of a level is
highly recommended. Drill 2” (50mm) deep holes
using a 5/16” (8mm) drill bit. Install Mount (C) to
the wall using Concrete Anchors (W-B), M6x50mm
Screws (W-A), and a Phillips screwdriver.
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 309-278-5303.
W-A
C
C
W-B W-A
STEP 2
F
E
Per Arm
G(x2)
Cover
G
G

4 5
Install Laptop Tray (E) to the VESA plate on Lower Arm (B) using M4x12mm Screws (M-A) and a
Phillips screwdriver.
Attach the lower arm assembly to the bottom post on Mount (C) using M6x25mm Spring Screw (S-A),
Screw Cap (S-B), and a Phillips screwdriver. Adjust the arm tension using 5mm Allen Wrench (T-B).
For best results, add your device to the arm then make tension adjustments as necessary.
Install monitor to the VESA plate on Upper Arm (A) using M4x12mm Screws (M-A) and a Phillips
screwdriver.
Install Lower Arm (B) to Arm Extension (D) using M6x25mm Spring Screw (S-A), Screw Cap (S-B),
and a Phillips screwdriver.
STEP 3
STEP 4
STEP 5
STEP 6
M-A
B
E
S-B
B
D
S-A
T-B
S-B
C
S-A
M-A
A

6 7
STEP 7
Adjust Laptop Tray
Tilt & Height Adjustments
Attach Upper Arm (A) to the upper post on Mount (C) using M6x25mm Spring Screw (S-A),
Screw Cap (S-B), and a Phillips screwdriver.
Use 5mm Allen Wrench (T-B) to adjust the tension and height of the arms. Turn Wrench
counter-clockwise to reduce tension for lighter monitors/laptops, and clockwise to increase
tension for heavier monitors/laptops. Arm rotation can be adjusted using the 3mm Allen
Wrench (T-A). Monitor tilt and rotation can be adjusted using the 5mm Allen Wrench (T-B).
Laptop tray clips can be adjusted 11.3” to 18.1” (288mm to 461mm) in width to securely hold
your laptop.
S-A
S-B A
C
T-B
T-B
T-A
T-B

LAST UPDATED: 03/20/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303