Vivotek AE-211 User manual

IP Surveillance
User’s Manual
AE-211/AE-232/AE-233
Rev. 1.0
Camera Enclosure

2
Specications
I
Model Number AE-211/AE-232/AE-233
Power Input 90~240VAC (+/-10%)
Rating Current 3.5 A
Heater Control 18 +/-3°C (ON) / 28 +/-3°C (OFF)
Blower Control 35 +/-3°C (ON) / 25 +/-3°C (OFF)
Environmental Operation Temp. -20°C ~ +50°C
Protection Level IP68
Temper Glass thickness 4mm
Mounting Bracket Fully-cable Management
Construction Die-cast Aluminum Alloy
Coating Ivory Powder & Stove Finish
Dimensions 425 (L) x 160 (W) x 165 (H) mm
Camera Space 275 (L) x 90 (W) x 100 (H) mm
Net Weight 5230 g
CAUTION:
TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
UNPACKING:
Unpack carefully. Electronic components can be damaged if improperly handled or
dropped. If an item appears damaged in shipment, place it properly in its carton and
notify the shipper.
IMPORTANT!
1. Read and follow Instructions: All operating and user instructions should be read and
followed before the unit is to be operated.
2. Electrical Connections: Only a qualied electrician is allowed to make electrical
connections.

3
English
Mounting Conguration & Dimensions
II
82.80mm
69.00mm
94.95mm
Swivel Positions and
Directions
Bracket Base Dimensions
BR-13 Full-cable Management
Bracket
160mm
68.5mm
83.2mm
425mm
165mm
Component Description
III
Camera Mounting
Platform Cable Conduits
Bushing Power Supply
Unit
Ground Wire
Blower
Terminal Block
Assembly
Thermal Control
Board
Heater
Shield
Heater

4
Wiring Diagram
IV
Shown below is the wiring diagram for the window demister. A spare 6-way terminal block
is provided at the rear of the chassis for additional camera and lens connections.
H1, Heater
STAT.1 TURN OFF at 28 C
TURN ON at 18 C
B2, Blower
STAT.2 TURN OFF at 25 C
TURN ON at 35 C
O
O
O
O
12VDC X4
3.5A or 5A
24VAC or
80~260VAC Input
H.1
or
B.2
PCB.1 CHASSIS EARTH
COVER EARTH
FTB. 1 FS. 1
TB. 1
TB.2
STAT.2
STAT.1
SPARE
PSU
TB.1 6 way terminal block
TB.2 3 way terminal block
FTB.1 Fused terminal block
STAT.1 18°C Thermostat
STAT.2 35°C Thermostat
H.1 Heater
PSU Power Supply Unit
P.C.B.1 Thermal control
circuit board
FS.1 3 Amp. Fuse
1. Pins 1, 2, 3, and 4 are DC 12V output for motor lens, siren, or speaker connecitons. If
they are not connected, remove cables from the connectors.
2. Pins 5 and 6 are DC 12V output for camera.
DC Output of PSU Connectors
H1. Heater
STAT.1 TURN OFF at 28°C
TURN ON at 18°C
B2. Blower
STAT.2 TURN OFF at 25°C
TURN ON at 35°C
Lines for
heater & blower
Pins 5 & 6
DC for camera
Pins 1 & 2
12V Output
Pins 3 & 4
12V Output
CHASSIS EARTH
COVER EARTH

5
English
Installation Suggestions
V
If you plan to install this camera enclosure into a tropical, sea coastal, or an environment
where salt water or corrosive industrial waste water/moist are present, please seal each
stainless steel screws and ttings with a silicon grease compounds. This will help prevent
electrolysis to occur and extend the life span of the camera and housing.
IMPORTANT!
1. Disconnect devices: A readily accessible disconnect device in the building installation
wiring should be incorporated.
2. Electrical Connection: Only a qualied electrician is allowed to make electrical
connections.
Features
Model Name
Heater:
On at 18OC
Off at 28OC
Blower
On at 35OC
Off at 25OC
PSU
(Power Supply Unit)
12VDC/24VAC 12VDC 080 324
080/F -• • -
080/HF • • • -
324/HF • • -•
1. 080: [90~240VAC input (+/-10%), 4x12VDC output, 3.5A]
2. 324 (24VAC input, 4x12VDC output, 3.5A)
Below are AC power connections to the FTB. 1 connector.
AC Power Connection
AC 24V Input AC 24V Input
Ground
Green Line