Well PROJ-LSR-RG6ID-WL User manual

USER’S MANUAL
Indoor Decorative Laser Light Projector
Model: PROJ-LSR-RG6ID-WL
Thank you for choosing WELL. Please read carefully the following instructions and keep them within
reach.
Specifications:
Input Voltage: 220 -240V AC, 50-60Hz
Output: 5V 1A 5W AC Adapter
Laser source: Red-100mw@650nm/ Green-20mw@532nm ( Class II Laser product)
Material: Al; IP20
Working temperature: 5℃~ 35℃
CAUTION! Performance of procedures other than those specified herein may result in hazardous
radiation exposure.
Class II laser products can be hazardous when directly viewed.
This laser is certified as a class II, laser product. Avoid direct viewing of class II laser energy. For
reference the FLPPS requirements for demonstration laser products like laser pointers are limited to
class II levels of laser energy. This product uses diffractive optics to scatter the beam energy. This
scattering effect causes the energy concentration to drop below the exposure limits for momentary or
accidental viewing at a relatively short distance from the laser aperture. This laser display device
incorporates a class II laser system which, by itself, maybe hazardous However, this laser display device
incorporates a protective housing and diffractive holographic optics in the machine’s design such that
there is no exposure or human access to the laser radiation during operation or maintenance above
the class II limits, Each individual laser beam’s power is less than 5mw, Which is about an average laser
pointer.

USER’S MANUAL
Indoor Decorative Laser Light Projector
Model: PROJ-LSR-RG6ID-WL
Warning! Under no circumstance shall attempts be made to open the protective housing or
operate the device if the aperture windows are damaged. All service to this laser display device
requiring the protective housing to be opened and /or removed shall be performed by a laser
service personal or their authorized agents. No user-serviceable parts-opening the outdoor laser
protective housing voids the warranty.
Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user’s authority to operated the equipment. This device complies with Part
15 of CE&ROHS Rules. Operation is subject to the following two conditions:(1) this device may not
cause harmful interference, and(2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
Important safety instruction
Please exercise the following precaution:
1. Do not aim or shine at people, animals or traffic from land sea or air.
2. Use with caution with 5-10 km of an airport.
3. This set is suitable for indoor use only. Please ensure that the transformer is plugged into
an internal power supply only. the set has a suitable lead cable for this purpose
4. Do not connect this set to any other light chain
5. Do not expose to direct heat or flame
6. Do not connect the light chain to the power supply while is still in the packaging
7. The power cable cannot be replaced. If the cable is damaged the set should be destroyed
8. Disconnect from the mains when not in use
9. It is quite normal for the transformer to become warm during use
10. Do not connect the light chain to the power supply directly, use only the transformer
supplied or one of equivalent rated voltage and wattage
11. Only for decorative use! For indoor use, IP20.
12. Never leave unattended or in a place where children or pets could reach or interact with
the product.
13. This decorative light is intended for decorative purpose only and not suitable for household
room illumination
Before your begin to use
Carefully unpack contents and check to make sure all parts are included: Laser light projector,
adaptor and 3 legs bracket

USER’S MANUAL
Indoor Decorative Laser Light Projector
Model: PROJ-LSR-RG6ID-WL
Using this product, please refer to the following steps:
1. Fix the mini laser light on the 3 legs bracket through the screw hole of the product
body and check all parts connected and fit well！
2. Connect the product to the adapter through the USB cable, insert the plug of the
power adaptor in the socket of the main voltage 230V for start the projector.
3. Please remove the power plug from the power socket for stop working
Waste electrical and electronic equipment are a special waste category, collection, storage,
transport , treatment and recycling are important because they can avoid environmental pollution
and are harmful to health. Submitting waste electrical and electronic equipment to special collection
centers makes the waste to be recycled properly and protecting the environment. Do not forget !
Each electric appliance that arrive at the landfill, the field , pollute the environment!
Importer & distributor:
SC VITACOM ELECTRONICS SRL
CIF: RO 214527
Tel. [phone]*
[e-mail] , www.vitacom.ro