Wenger Class Piano Workstation User manual

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly Instructions
Class Piano Workstation
©Wenger Corporation 2020 Printed in USA 2020-04 Part #222E135-03
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp.com
Contents
Note: Please read and understand these instructions before starting the assembly.
Note: If you need additional information, contact Wenger Corporation using the information below.
Visit the Class Piano Workstation web page at wengercorp.com for more information.

2
Important User Information
General
Copyright © 2020 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form or
by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage
and retrieval systems without the written permission of the publisher, unless it is for the purchaser's personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment on the part of
Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in these
instructions.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect,
special, incidental, or consequential damages resulting from the use or defect of these instructions.
The manufacturer reserves the right to change this product at any time.
The information in this document is not intended to cover all possible conditions and situations that might occur. The
end user must exercise caution and common sense when assembling or installing Wenger Corporation products. If any
questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or [phone] worldwide.
Manufacturer
The Class Piano Workstation is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
wengercorp.com
Intended Use
• This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
• This product is intended to be assembled and used only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ve full years from date of shipment.
A full warranty statement is available upon request.

3
The following tools are required for assembly.
• Phillips head screwdriver
• 4 mm hex wrench (supplied) if installing on a 76-key piano
Required Tools
Item Qty Description
11Workstation Desk
28Suction Cup
32Wire Grommet
41Power Strip
51Plastic Rear Cover
64#8-32 x 3/4" Machine Screw
71Music Holder
Parts List
7
4
6
1
2
5
3

2. Insert two wire grommets (2) into the slots on the top side of the workstation desk.
4
Assembly
1. Screw eight suction cups (2) into the inserts on the bottom side of the workstation desk (1).
Tighten securely.
Wire
Grommet
(3)
Suction
Cup
(2)
Workstation
Desk
(1)

5
Assembly (continued)
The Class Piano Workstation is shipped to t on top of a 88-key digital piano.
To t on top of a smaller 76-key digital piano, the end support panels can be moved in.
To move the end support panels, follow the step below before proceeding.
Otherwise skip ahead to the next page.
STOP
3. Turn the workstation desk onto its top.
On both end support panels:
a. Turn and unlock the two cam connectors in the side panel.
b. Remove the hex socket screw from the back panel.
c. Lift the end support panels o󰀨 the connecting bolts
d. Move the connecting bolts to the inner set of holes.
e. At the new location, place the end support panels onto the connecting bolts and reattach.
Cam
Connectors
Standard
88-key
position
Moved to
76-key
position
Standard
88-key
position
Moved to
76-key
position
88-key
positions
Hex Socket
Screw
Connecting Bolts
(at 76-key position)

6
Assembly (continued)
4 Set the workstation desk to t on top of the piano as shown.
Press down rmly to secure the suction cups

7
Assembly (continued)
5. Attach the power strip (4) at the back side of the workstation desk under the desk surface using the
included hardware.
6 Wires, cords and cables can all be fed through the wire grommets.
Power
Strip
(4)
Feed wires,
cords and cables

8
Assembly (continued)
7. Attach the plastic rear cover (5) to the pilot holes at the back side of the workstation desk using
four #8-32 x 3/4" Machine Screws (6).
Rear Cover
(5)
8 Slide the music holder (7) over the front edge of the upper desk surface as shown.
#8-32 x 3/4"
Machine Screw
(6)
Music
Holder
(7)