Winsted 56826 User manual
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Pole Mount (56826)
Slat Wall Mount (58178/30178)
Height-adjustable Monitor Mounts
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
56826/58178/30178
56826/58178/30178 Installation Instructions
2
DISCLAIMER
Winsted Control Room Consoles and its affiliated corporations
and subsidiaries (collectively “Winsted”), intend to make this
manual accurate and complete. However, Winsted makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Winsted
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Winsted assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Winsted® is a registered trademark of Winsted Control Room
Consoles. All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounting system/
accessories are properly assembled and installed using the
instructions provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return themounting system toa service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located attached to the Height-adjustable
Monitor Mounts up to (and including) the display does not
exceed the weight limits listed below. Use with products
heavier than the maximum weight indicated may result in
collapse of the mount and its accessories causing possible
injury.
--SAVE THESE INSTRUCTIONS!--
MODEL Max Weight
Allowed for EACH
Display
Max Weight
Capacity of
Mounting System
Pole Mount
(56826) 25 lbs
(11.34 kg) 25 lbs
(11.34 kg)
Slat Wall
Mount (58178/
30178)
25 lbs
(11.34 kg) 25 lbs
(11.34 kg)
Installation Instructions 56826/58178/30178
3
DIMENSIONS
Pole Mount (56826)
2.95
75.0
3.94
100.0
2.95
75.0
3.94
100.0
DYNAMIC HEIGHT
ADJUSTMENT RANGE
OF APPROXIMATELY
23.70
10.70
[601.1]
[271.8]
8.50
215.9
1.94
49.4 MAX
1.43 MIN
[36.3]
DYNAMIC LIFT ARM
LENGTH RANGE
APPROXIMATELY
STRAIGHT = MAX
FULL UP/DOWN = MIN
10.21
259.3
7.12
[180.9]
2.32
59.0
Slat Wall Mount (58178/30178)
2.95
75.0
3.94
100.0
3.94
100.0 2.95
75.0 DYNAMIC HEIGHT
ADJUSTMENT RANGE
OF APPROXIMATELY
16.13
3.85
[409.7]
[97.8]
9.23
234.4
DYNAMIC LIFTARM
LENGTH RANGE
APPROXIMATELY
STRAIGHT = MAX
FULL UP/DOWN = MIN
10.21
259.3
7.12
[180.9]
2.32
59.0
56826/58178/30178 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions 56826/58178/30178
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
3/16” (included)
1/8” (included with slat wall only)
5/32” (included with pole mount only)
1/2”
A (1)
[Pole clamp arm]
(56826)
B (4)
M4x14mm C (4)
M4x25mm D (4)
M10x5.3x10
3/16” 1/8”
L (1) M (1)
E (1)
[pole clamp]
F (4)
1/4-20 x 1 1/2” G (4)
1/4-20 x 1"
5/32”
K (1)
OR
A (1)
[Slat wall mount arm]
(58178/30178)
with Pole Mount (56826) ONLY
(pole mount only) (slat wall mount only)
56826/58178/30178 Installation Instructions
6
Assembly And Installation
Connecting to Pole (56826)
1. Determine approximate location for mount keeping in mind
display size, extension, height adjustment requirements.
2. Place mount (A) against pole with clamp (E) on opposite
side of pole. (See Figure 1)
Figure 1
3. Using 5/32” hex key (K) and appropriate length screws,
loosely attach assembly to pole clamp(E). If installing to
11/2”NPTpipe,use1/4-20x 1 1/2”buttonheadcapscrews
(F). If installing to 1 1/2” diameter pipe, use 1/4-20 x 1"
button head cap screws (G). (See Figure 1)
4. Position mount at desired height and orientation.
5. Equally tighten screws against mount and the pole clamp.
Connecting to Slat Wall (58178/30178)
1. VerifymountingbracketsonOFBUbracketcanmovefreely.
(See Figure 2)
Figure 2
2. Locate desired installation location and slide upper
mounting plate into wall making sure bracket is seated in
channel bottom. (See Figure 3)
3. Let lower mounting plate rest against wall.
4. Using 1/2” socket, tighten tension hex head bolt until lower
mounting plate slides into channel in wall and continue
tightening until resistance is felt. (See Figure 3)
Figure 3
5. Tighten two upper and lower button head cap screws to
secure OFBU bracket to wall. (See Figure 4)
Figure 4
3
(F or G) x 4
(E)
(A)
x4
OFBU bracket
1
(arm not shown
for clarity)
2
3
4
OFBU bracket
4
(arm not shown
for clarity)
OFBU bracket
x4
OFBU bracket
5
5
(arm not shown
for clarity)
Installation Instructions 56826/58178/30178
7
Display Installation
The mounting holes on the back of the display will either be
flush with the back surface or recessed into the back surface.
Refer to the applicable installation procedure.
Flush Mounting Holes
CAUTION: Using screws of improper size may damage
your display! Proper screws will easily and completely thread
into display mounting holes.
CAUTION: Inadequate thread engagement in display may
cause display to fall! Back out screws ONLY as necessary to
allow installation of Centris bracket!
1. Ensure faceplate is able to swivel and tilt easily, yet still be
tight enough to hold display in desired position. Adjust as
requiredbeforeproceeding.See“ADJUSTMENT”fordetail.
(See Figure 5)
2. Using Phillips screwdriver, carefully install two M4x14mm
screws (B) into the upper mounting holes on the display.
Thread screws completely into display, then back out 3
complete turns. (See Figure 5)
3. Pickup andaligndisplayso thatscrews(B) (installed onthe
back ofthe displayin the previous step) fit into the mounting
holes on the faceplate. Rotate the bracket as required.
Lower the display firmly into place. (See Figure 5)
Figure 5
4. Using Phillips screwdriver, install two remaining M4x14mm
Phillips screws (B) through the lower mounting holes in
faceplate into the display. (See Figure 5)
5. Tighten all four screws (B). Do not overtighten!
Recessed Mounting Holes
1. Ensure Centris bracket is able to swivel and tilt easily, yet
still be tight enough to hold display in desired position.
Adjustasrequiredbeforeproceeding.See“ADJUSTMENT”
for detail.
2. Carefully place display face down on protective surface.
3. Place the fourspacers (D) over each of the mount holes on
the back of the display. (See Figure 6)
4. Pick upand orient the mount (A) so thatthe mounting holes
are aligned with the holes in the spacers; rotate the bracket
as required. (See Figure 6)
5. UsingPhillipsscrewdriver,installfourM4x25mmscrews(C)
through the mounting holes, through the spacers and into
the display. (See Figure 6)
6. Tighten all four screws. Do not overtighten!
Figure 6
Lift Arm Tension Adjustment
1. Tension may be adjusted with tension adjustment screw
inside cable managementcover and 1/8” hex key (M).Turn
clockwise to reduce tension or counter-clockwise to
increase tension. (See Figure 7)
Figure 7
2
4
3
(D) x 4
5
(C) x 4
(A)
3
Reduce tension
Increase tension
(lighter display)
(heavier display)
Do NOT over-tension
adjustment tension
screw.
56826/58178/30178 Installation Instructions
8
Pivot Adjustment Range
1. Adjust arm angle as desired up to 90 degrees in either
direction. (See Figure 8)
WARNING: Swinging the arm beyond 90 degrees may
result in the mount slipping off the desk causing serious
injury!
Figure 8
Cable Management
1. Press insides of cable management covers at both ends to
unhinge tabs on either end of cable management cover on
upper arm. (See Figure 9)
2. Lift cable managementcoverup until tabsare unhinged and
cover is in the “open” position. (See Figure 9)
Figure 9
Figure 10
3. Route cables through cable management channels. (See
Figure 10)
IMPORTANT ! : Be sure to leave enough slack in the
cables near display and arm joint to allow for full arm
articulation!
4. Close cable management covers on monitor arm. (See
Figure 10)
5. Repeat Steps 1-4 for lower arm.
(top view)
+/- 90 degrees range
of motion
pivot point of the arm
cable management cover tabs
1
2
2
2
4
4
3
3
cable (typical)
Installation Instructions 56826/58178/30178
9
56826/58178/30178 Installation Instructions
10
Installation Instructions 56826/58178/30178
11
This manual suits for next models
2
Table of contents
Other Winsted Rack & Stand manuals
