Workzone WZ-TB 13 L User manual

BENCH DRILL
WZ-TB 13 L
User Manual
Original instructions
ID: #05007
m
y
h
a
n
s
e
c
o
n
t
r
o
l
.
c
o
m
M
A
N
U
A
L
D
E
V
E
L
O
P
E
D
I
N
G
E
R
M
A
N
Y
User-friendly
Manual

Dok./Rev.-Nr. 196433_20180806
Overview .................................................................................. 3
Use............................................................................................. 4
Pack contents/device parts ..................................................... 6
General information..................................................................7
Reading and storing the user manual ........................................ 7
Explanation of symbols ................................................................. 7
Safety ........................................................................................ 8
Proper use........................................................................................8
Residual risks...................................................................................9
General safety notes for power tools...........................................9
Safety notes for drills.....................................................................12
Safety notes for the line laser ..................................................... 13
Safety instructions for batteries................................................. 13
Supplementary safety instructions ........................................... 14
Check the drill and package contents....................................16
Assembly .................................................................................16
First use.................................................................................... 17
Operation................................................................................. 17
Preparations.................................................................................. 18
Emergency stop switch................................................................ 18
Setting the speed ......................................................................... 19
Speed table.....................................................................................21
Setting the height of the protective hood................................ 22
Clamping the workpiece in the vice ..........................................22
Adjusting the drilling table .........................................................22
Setting the drill depth..................................................................23
Switching on and setting the line laser.....................................23
Drilling workpieces.......................................................................24
Tips for best results when drilling..............................................25
Removing blockages....................................................................26
Cleaning and maintenance.................................................... 26
Storage ................................................................................... 28
Transport ................................................................................ 28
Troubleshooting..................................................................... 29
Technical data ........................................................................ 29
Noise information .................................................................. 30
Disposal....................................................................................31
Declaration of conformity.......................................................32
Contents

3
A
B
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
2
19
20
21 22
23
18
24

4
F
29
7
21
10
12
7
9
D E
C
2728
7
11
26
25

5
14
13
15
14
19
12
20
I
L
G H
K
J
6
30
26
31

6
Product contents⁄device parts
1Protective hood
2Locking screw
3Motor
4Tensioning screw for the motor
5Handle fixture
6Handle, 3×
7Drill column
8Scale for setting the incline
9Rotary knob for setting the height
10 Base plate
11 Screw for setting the incline
12 Drilling table
13 Chuck
14 Protective hood
15 Foldable chip guard
16 Arrow mark for setting the drill depth
17 Emergency stop switch
18 Clamping screw for setting the drilling
depth, 2×
19 Vice
20 Fixing screw, 2×; washer, 4×;
spring washer, 2×; nut, 2×
21 Hexagon screw, 3×
22 Screw for line laser
23 Hex key
24 Chuck key
25 Tension lever for V-belt
26 Line laser
27 Rotating bezel, 2×
28 On/Off switch for the line laser
29 Grub screw, 2×
30 Battery compartment cover
31 On/Off switch I/O (On switch I: green;
Off switch O: red)
The product contents include two R03 1.5 V batteries (AAA).

General information
7
General information
Reading and storing the user manual
This user manual accompanies this bench drill WZ-TB 13 L (hereinafter
referred to simply as “drill”). It contains important information on safety,
usage and care.
Read the user manual carefully before using the drill. Pay particular
attention to the safety instructions and warnings. Failure to follow the instructions in
this user manual may result in serious injury or damage to the drill.
You must comply with applicable local or national regulations concerning the use of
this product. Keep this user manual in a safe place for future reference. If you pass the
drill on to third parties, please be absolutely sure to include this user manual.
Explanation of symbols
The following symbols and signal words are used in this user manual, on the drill or
on the packaging.
WARNING!
Indicates a hazardous situation that, if not
avoided, could result in death or serious injury.
NOTICE!
Warns of possible damage to property.
This symbol provides you with useful supplementary information on
assembly or use.
Declaration of conformity (see chapter “Declaration of conformity”):
Products marked with this symbol meet all applicable Community
regulations for the European Economic Area.
Read the user manual.
Wear suitable, tight fitting clothing.
Wear protective goggles.

Safety
8
Wear a dust mask.
Wear ear protection.
If applicable, wear a hair net or cap to prevent your hair from getting
caught in rotating parts.
This device complies with protection class I.
VORSICHT ! - LASERSTRAHLUNG !
Nicht in den Strahl blicken!
Laser Klasse 2
λ: 650 nm; P: < 1 mW
nach EN 60825-1: 2014
Products marked with this warning notice are laser devices
of class 2 with a wavelength of 650 nm and comply with EN
60825-1:2014. You may not look directly into the beam emitted
by these products or use optical instruments to view them.
Safety
Proper use
The drill is only suitable for hobby and DIY tasks for drilling materials such as stone,
wood and metal. It must not be used to drill into work materials that are hazardous to
health such as asbestos.
The chuck is suitable for drill bits and tools with a shank diameter from 1.5 up to a
maximum of 13 millimetres and cylindrical tool shank. Tools with a taper shank (MK2)
can also be used.
The drill must not be operated continuously for more than 15 minutes. Afterwards, the
drill must cool off before it is used again.
The drill may only be used by adults.
Any other applications are expressly prohibited and are deemed improper use.
Neither the manufacturer nor the retailer can accept any responsibility for injury, loss
or damage caused by misuse of this product of any kind.
Examples of misuse are given in the following non-exhaustive list:
• Using the drill for other purposes than those which are intended;
• Failure to observe the safety instructions and warnings as well as the assembly,
operating, maintenance and cleaning instructions contained in this user manual;
• Failure to comply with any regulations relating to accident prevention,
occupational medicine or safety which specifically and/or generally apply to the
use of this drill;

Safety
9
• Usage of accessories and spare parts which are not intended for the drill;
• Modifications to the drill;
• Repairs to the drill by parties other than the manufacturer or a qualified
professional;
• Use of the drill for commercial or industrial applications as well as in connection
with the trades;
• Operation or maintenance of drill by persons not familiar with how to handle the
drill and/or who are not aware of or do not understand the associated risks.
Residual risks
Despite proper use, inconspicuous residual risks cannot be completely ruled out.
Depending on the type of drill, the following hazards may occur:
• Lung injury if a suitable dust mask is not worn;
• Hearing loss if suitable ear protection is not worn;
• Injury to health if the drill is not used or maintained properly;
• Injury to health attributed to hand and arm vibration if the drill is used over a
prolonged period of time, is not guided in a controlled manner and maintained
properly;
• risk of injury if long hair, loose-fitting clothing or jewellery get caught by rotating
device parts.
General safety notes for power tools
WARNING Read all the safety notes, instructions, illustrations and
technical details supplied with this power tool. Failure to follow the safety
notices and instructions may result in an electric shock, fire and/or severe
injury.
Keep all safety notes and instructions for future reference.
The term “power tool” used in the safety instructions refers to mains-operated
power tools (corded) and battery-powered power tools (cordless).
Work place safety
a) Keep your work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not work with the power tool in areas with a risk of explosion
where flammable liquids, gases or dusts are present.
Power tools
create sparks which may ignite the dust or fumes.

Safety
10
c) Keep children and other persons away from the power tool while
you are using it. If you are distracted, you could lose control of the
power tool.
Electrical safety
a) The connector plug for the power tool must fit in the socket. The plug
must not be modified in any way. Do not use any adapter plugs in
combination with power tools with protective earthing. Unmodified
plugs and matching outlets will reduce the risk of electric shock.
b) Avoid body contact with earthed surfaces like pipes, heaters,
stoves and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Keep power tools away from rain or moisture.
Water entering a
power tool will increase the risk of electric shock.
d) Do not use the cord for improper purposes such as for carrying
the power tool, for hanging it up or for pulling or unplugging
it from the socket. Keep cord away from heat, oil, sharp edges
and moving parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use only extension cords
that are suitable for outdoor use.
Use of a cord suitable for outdoor
use reduces the risk of electric shock.
f) If operating the power tool in a damp environment cannot be
avoided, use a RCD. Use of an RCD reduces the risk of electric shock.
Safety of persons
a) Be careful, pay attention to what you are doing and approach
work with a power tool in a reasonable manner. Do not use
any power tool if you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating
power tools may result in serious personal injury.
b) Wear personal protective gear and always wear safety glasses.
Protective equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will reduce
personal injuries.