Yard Craft Cydonia Vinyl Playset User manual

Assembly Manual
Cydonia Vinyl Playset

Tools Required for Job
One 4' Step
Ladder
Cordless Drill
& 1/2" drill bit
25’ Tape
Measure
Cydonia Vinyl Playset
Assembly Manual
Thank you for your purchase of this playset.
This manual is designed to simplify the assembly process, however we recommend having an experienced
carpenter involved in the project. Please read through the entire manual before starting!
Take a deep breath and get at it; the satisfaction and enjoyment of this hideout is only a few minutes away.
Have fun!
You have purchased a product that consists of bulky pieces. With your purchase, you assume full
responsibility to have the necessary manpower available to assemble the product. We reccomend at least
two able-bodied men for this assembly. You also agree that any damage that happens to the product during
the entire construction process is your responsibility, and neither the seller, nor the manufacturer, will be
held liable for any such damage.
9/16th Wrench
#2 Square
Drive Tip
(included)
T30 Star
Drive Tip
(included)

Parts List

4
Cydonia Vinyl Playset Assembly Manual
Unpack and identify parts. Identify and then place two 2x6x 73 1/2" and two
2x6x56" on a smooth, flat surface to begin. Make sure
floor joist hangers are turned in. Also notice shims at
four corners.
Thread 6 3/8" bolts into T-nuts on four corners. Fasten four 4x4x54". Pre-drilled hole configuration is
very important on all 4x4's. Hand tighten acorn
nuts at this point. Be sure to always place washer
between vinyl and acorn nut.
Step 1:
Step 4:
Step 3:
Step 2:

5
Continue fastening 2x6's to 4x4's using 6 7/8" bolts. Tighten nuts at this point. Over-tightening acorn nuts
can cause the head to pop off.
Install three floor joists. Fasten joists to hangers using 1 3/4" washer head
screws.
Step 5:
Step 8:
Step 7:
Step 6:
Cydonia Vinyl Playset Assembly Manual

6
Lay out floor boards. Notice the two shorter ones
between posts and narrow one in the center. Make sure
the floor boards are flush with the 2x6.
Fasten using 1 1/2" screws.
Measure to ensure the floor frame is square before
continuing.
Using 6 7 /8" bolts, being fastening 2x6's to tower 4x4.
Thread acorn nut onto rod as far as you can, then back off
several turns. Be sure to place washer between acorn and
vinyl. Only tighten acorn nuts after brackets are on each
corner.
Step 9:
Step 12:
Step 11:
Step 10:
Cydonia Vinyl Playset Assembly Manual

7
Fasten top and bottom flanges of corner bracket using
1 3/4" screws.
Fasten slats to tower using pattern provided to find
proper spacing. Be sure you know where any
components you may have purchased will be attached
prior to fastening slats. Use 1 3/4" screws to fasten slats.
Assembly instructions for the components can be found
on pages 23-26.
Prepare to assemble legs by identifying two
2x6x 81 1/2" with long point on one end. Also, one
2x5x79 1/2" with braces attached.
Fasten 2x6x81 1/2(with long point) using 3 1/2"
stainless steel lag screws. Be sure this is flush.
Repeat on opposite side.
Step 13:
Step 16:
Step 15:
Step 14:
Cydonia Vinyl Playset Assembly Manual

8
Fasten brace to 2x6x81 1/2" using 3 1/2" stainless steel
lag screw. Repeat steps 15-17 for second leg.
Prepare to fasten leg to tower. Start four 4 3/8" bolts in holes before lifting
platform into position.
Step 17:
Step 20:
Step 19:
Step 18:
Cydonia Vinyl Playset Assembly Manual

9
You are now ready to fasten second leg. Propping on a
5' step ladder works great.
Step 21:
Step 24:
Step 23:
Step 22:
Leg assembly and tower assembly should join together
like this. 4 3/8" bolts that were started in previous step
can be fastened into the t-nuts. Also on opposite side.
Fasten long point to 4x4 using 4" lag. You may need
to drill a 1/4" or 5/16" pilot hole in the 4x4.
Repeat steps 19-24 to fasten second leg.
Cydonia Vinyl Playset Assembly Manual

10
You are now ready to install the
cargo net, rock wall, and step ladder
panels.
These are interchangeable at all
locations on the "legs."
Decide where you want these
positioned prior to fastening.
Typically there is one "empty"
space where the slide goes.
Cydonia Vinyl Playset Assembly Manual

11
These components should now be fastened in place
using 3 1/2" stainless steel lag screws. A lag should be
put in at this location on both the rockwall and cargo
net.
Fasten about halfway up the "leg" as well.
Fasten a 3 1/2" stainless steel lag screw at these
locations as well.
Fasten two lags at this location on the outside as well.
Step 25:
Step 28:
Step 27:
Step 26:
Cydonia Vinyl Playset Assembly Manual

12
Short pieces of decking should be fastened after
installing the rockwall and cargo net.
Step 29:
Step 32:
Step 31:
Step 30:
Install the step ladder.
Install 2x6 on "leg" at the slide location. This is to
provide reinforcement to the structure. Three lags
should be used to fasten this.
The next step is to install the roof.
Assembly instructions for the pyramid roof can be
found on page 13.
Cydonia Vinyl Playset Assembly Manual

13
Space roof equally at all four corners.
Pre-drill 5/16" hole, then fasten using 3/4" bolt,
two washers, and lock nut at four corner.s
Your completed plastic roof should look like this.
Step 2:
Step 4:
Step 3:
Pyramid Roof Assembly Instructions
Step 1:
Fasten flat roof bracket to top of post using three 3"
screws. Repeat on four posts always with tab towards
the center of the tower.

14
Attach step ladder handle to the right of the step ladder
using four 1 1/2" wafer-head lags.
Attach at top and bottom.
Step 42:
Step 43:
Step 41:
You are now ready to install the tire swing.
Attach tire swing swivel under the deck
using 3" lags.
Then attach the tire swing to the swivel.
Attach slide using 1 3/4" washer-head screws.
The next step is to install the swing frame(s).
Instructions for the swing frame can be found on
pages 15-19.
Instructions for the climbing set can be found on
pages 20-22.
Cydonia Vinyl Playset Assembly Manual

15
You are now ready to assemble the swing frame. Begin
by identifying the swing beam.
The end of the beam without caps gets fastened to the
tower.
Fasten swing bearings to swing beam using lags
provided in bearing packs.
Step 2:
Step 1:
Swing Frame Assembly
If you purchased a plastic glider, your next step is to
install the glider bracket. This bracket needs to be
fastened to the opposite side of the swing beam as the
swing bearings. It can be placed at any swing position.
Pre-drill four 1/2" holes, then fasten using four lag
screws provided.
Step 3:Step 4:

16
Finish fastening using the 1 3/4" washer head screws
provided.
Rotate the swing beam 180 degrees so that the swing
bearings are turned up. Fasten the swing beam receiver
bracket to the swing beam using two 4 7/8" bolts
provided. This bracket needs to be fastened to the end of
the swing beam without the caps. Thread acorn nut onto
bolt as far as you can, then back off several turns. Use
washers between the acorn nut and the metal bracket.
Tighten nuts.
Step 6:
Step 5:
Swing Beam Assembly
With swing beam in same position, attach beam strap to
swing beam using two 4 7/8" bolts provided. Only
finger tighten at this point. Note that this end of the
beam should have caps on it. This bracket is fastened
36" from the end of the 14' beam. Use pre-drilled holes.
Step 7:
Step 8:
Identify end post and place between beam strap. Fasten
using two 4 7/8" bolts provided. You are now ready to
tighten all four bolts on beam strap.
If your setup location is level, the end post will need to
be shortened approximately 1' (cut off bottom end).

Step 12:
Step 11:
Lift swing beam into position. One person should be up
in the tower. The other person should continue to hold
the end post steady.
Note: your set may not appear exactly as pictured
Swing Beam Assembly
Step 9:Step 10:
Fasten corner brace to swing beam and end post. Be
sure end post is plumb. Attach using six 1 3/4" washer
head screws.
Push bracket against 2x6 vinyl then fasten first with
two lags provided.
Next predrill 7/16" holes and fasten with two 2 3/4"
bolts provided, using acorn nuts and washers.
17

18
Swing beam receiver properly fastened. Identify ground runner and fasten to end post using
6 1/2" bolts. Thread acorn nut onto rod as far as you can,
then back off several turns. Be sure to place washer
between acorn nut and vinyl.
Step 13:
Step 16:
Step 15:
Step 14:
Identify end post braces. Fasten the short angle to the
ground runner that was installed on previous step.
Use 4 /18" bolts provided.
Align brace with end post then fasten long angle to end
post using 3/8" x 4" lags provided. This should be pre-
drilled using 1/4" drill bit.
Swing Beam Assembly

19
Step 17:
Swing Beam Assembly
Your completed swing frame should
appear like this.
The next step is to install the climbing set.
Instructions for the climbing set assembly can
be found on pages 20-22.

20
Step 2:
Step 1:
Climbing Set Assembly
One one end, fasten two brackets as shown, using
four 2 5/8" bolts (this is an upside down position).
Step 3:
You are now ready to assemble climbing beam. To
begin, identify the main components; one top ladder,
one ground runner 2x4, and two brace 2x4's, and one
end ladder.
On opposite end, fasten end ladder to top ladder using
four 4 1/8" bolts. Tighten using a 9/16" deep socket
and a 9 1/6" open end wrench. Keep in mind that
over-tightening can damage the acorn nut.
Step 4:
Flip ladder into upright position and place at desired
location on playset.