Zeiss 5034555 User manual

ZEISS Server
User Manual (Version 2.0)

EN_20_012_0043l
© 2020, Carl Zeiss Vision GmbH
Familiarity with this user manual is required to operate this device. Therefore, please
familiarize yourself with its contents and in particular follow the instructions pertain-
ing to safe use of the device.
We reserve the right to make changes without notice; the user manuals are not sub-
ject to the change service.
All of the data in this documentation has been obtained through extensive produc-
tion testing and reflects the current state of knowledge, current legal provisions as
well as the applicable standards as of the publication date. These documents do not
lose validity in the event of changes to relevant laws or standards. The user of the
product is responsible for respecting all trademarks or existing laws.
Specifications are only binding where they are set forth as binding in written offers
and the accompanying documents to the product.
Please note that the device may differ from the technology described in this docu-
ment by version, equipment and other criteria. We reserve the right to make
changes to the delivery scope and contents without prior notice.
Any distribution and reproduction of this document use and sharing of its contents
is prohibited without express written permission. Any breach or infringement will re-
sult in liability for damages. All rights reserved in the event of a patent award or util-
ity model registration.

Contents 3
EN_20_012_0043l
Contents
1Storage.............................................................................4
2Installation........................................................................4
3The Installation Position...................................................4
4Power supply....................................................................5
5Ambient conditions ..........................................................5
6Expansion and Repairs .....................................................6
7Maintenance.....................................................................6
8Battery..............................................................................6
9Additional safety instructions...........................................6
10 Shutdown .........................................................................7
11 Disposal ............................................................................7
12 Other provisions ...............................................................7
13 Technical data ..................................................................8
14 Instructions for the ZEISS Server function........................9

4 Storage
EN_20_012_0043l
1Storage
The device must be stored in its original packaging in a dry and vibration-
free environment. The stipulated ambient conditions must be observed.
2Installation
In the final application of the device, safety and fire-control regulations must
be observed and followed.
The device must be used in dry, enclosed spaces only. The stipulated ambi-
ent conditions must be observed. Condensation may form if the device is
transported from a cold environment into the place of use.
Before starting up the device, the temperature must be adjusted and remain
constant. A minimum distance of 100 mm from walls or other objects must
be maintained in order to ensure sufficient ventilation. Existing fan vents and
cooling units in the housing must not be covered. The device must not be in-
stalled in the vicinity of radiators or fan heaters. Direct sunlight is to be
avoided.
The footprint must be stable and largely free from vibrations.

Do you want to be certain that the device can be operated in
the place of use? Then ask us.
3The Installation Position
Horizontal and vertical installation Safety as well as fire-control regulations
must be observed when not conforming to the prescribed position.

Do you want to be certain that the device can be operated in
the intended location? Then ask us.

Power supply 5
EN_20_012_0043l
4Power supply
The system can only be operated with the following power supply.
Manufacturer: FSP, Model: FSP075-DHAN3
The power rating information listed on the type plate does not correspond
to the power required by the device. Rather, the power rating information is
only there for reasons of product safety and is intended to ensure the cor-
rect voltage and to protect the external supply source. The device's actual
power rating falls below these levels.
Before connecting it with the line supply, it is necessary to check if a selector
switch, when available, is set for the local line supply voltage. If in doubt, in-
quire at the energy provider responsible. The device must be grounded: via
the power supply or other appropriate measures.
The device must be secured by a building fuse of max. 16A to ensure safe
operation. Ensure that the power socket on the device or the line supply out-
let is freely accessible. The device can be disconnected from the line supply
by pulling the power cord.
For DC supply: the power supply voltage in the DC cable must match a con-
stant voltage classified as ES1 in accordance with EN62368-1. Before con-
necting the power supply cable, ensure you check the polarity of the power
supply voltage. When needed, a potential equalization for malfunction-free
operation may be necessary. With an external adapter, ensure that the
power supply circuit points on the device or the line supply outlet are freely
accessible. The device can be disconnected from the power supply by pulling
the power supply cable. Ensure that the cords are not a potential hazard
(tripping hazard) and cannot be damaged.
5Ambient conditions
Operation: +10°C —40°C
Storage: -20°C —60°C
Humidity: 10% —90%, no condensation formation.
Correct performance cannot be ensured outside of these parameters.
The values may fluctuate when used with an uninterruptible power supply -
UPS (see the user manual for a UPS).

6 Expansion and Repairs
EN_20_012_0043l
6Expansion and Repairs
The device may only be opened by authorized specialized personnel. Unau-
thorized opening or repairing the device improperly can lead to considerable
risks for the user, such as an electric shock or the risk of fire.
The power supply unit must not be opened for any reason! When fitted with
a UPS, the safety instructions for operating the UPS must be followed.
Expanding the device can alter the CE relevant properties to such a degree
that conformity with the valid standards is no longer guaranteed.
7Maintenance
The existing fan vents must be checked regularly (depending on the location)
for dirt and permeability and cleaned if necessary. All fans must be checked
1x per year.
8Battery
The main board is fitted with a battery. Only authorized technicians are per-
mitted to replace it.
There is a risk of explosion if the battery is replaced improperly the battery
should only be replaced with an identical or equivalent type recommended
by the manufacturer.
Used batteries must be disposed of via the CCR REBAT return device in ac-
cordance with local laws and regulations. The battery from the main board
must be changed every 4-8 years depending on the ambient conditions
(temperature, operating time).
9Additional safety instructions
Data transfer capabilities must neither be connected nor disconnected dur-
ing a storm.
LAN interface cables must not exceed 30m in length.
In an emergency situation (e.g. if the device or the line voltage is damaged
or if fluid or foreign bodies enter the device), pull the power cord and inform
your local retailer or our service.

Shutdown 7
EN_20_012_0043l
10 Shutdown
Systems without UPS can still carry voltage for up to 10 seconds after the
device has been unplugged from the line. The storage instructions must also
be observed.
11 Disposal
The electronic components used in the device, such as the main board, bus
board, hard drive, the power supply unit, etc., must not be disposed of as
domestic waste. Instead, they must be disposed of by appropriate specialist
companies.
In accordance with the requirements set down in the EU directive on Waste
Electrical and Electronic Equipment 2012/19/EU (WEEE Directive), this device
must be labelled with a WEEE logo in accordance with standard DIN EN
50419.
(crossed-through garbage can with stripes under the symbol)
12 Other provisions
Keep these installation instructions with the device. These installation in-
structions should be included if the device is passed on to third parties.
In the version delivered, this device fulfils the requirements set down by the
EMC directive 2014/30/EC and LVD directive 2014/35/EC.
In its condition upon delivery, this device conforms to the conditions in the
RoHS directive (2011/65/EU) incl. 2015/863/EU) on the restriction of the use
of certain hazardous substances in electrical and electronic equipment.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense. This
class A digital device conforms to the Canadian "Interference-Causing Digital
Equipment Standard ICES-0003" stipulations and requirements.
These installation instructions are valid for the product families ZEISS Server.

8 Technical data
EN_20_012_0043l
13 Technical data
Electrical power rating
Rated voltage
100 —240 V AC ±10%
Rated frequency
50 —60 Hz
Protection class
I
Plug-in connection
CEE 7/7 Hybrid
Power consumption
through 1,2 A
Ambient conditions for the intended use
Temperature
+10 °C —40 °C
Humidity
10 % —90 % (non-condens-
ing)
Dimensions and weights
Dimensions (height x width x
depth)
112 x 355 x 220 mm
Weight
4,7 kg
Device type
Name
ZEISS Server
Model
5034555
Interface (front side)
Standby with LED status display
1 x RGB-LED button
Changeable frame
1 x 3,5” SATA HDD for backup
Interface (back side)
Monitor interface
1x DVI-I
LAN
1x Gigabit Ethernet
USB
2x external USB 3.1 ports
1x external USB 2.0 ports
PS/2
1x Mouse
1x Keyboard
DC-IN plug
1x 12 V DC
COM
1x RS232

Subject to change in design and scope as well as technical
changes.
Fig. 1: Type plate for ZEISS Server

Instructions for the ZEISS Server function 9
EN_20_012_0043l
14 Instructions for the ZEISS Server
function

Note the installation conditions described in chapters 2 and 3.
If you wish to install the ZEISS Server vertically, ensure that the footprint is
covered with the enclosed rubber pads (Figure 2/1).
It is important that the server footprint is always the right-side surface (the
side surface which lies on the side of the drive's changeable frame).

Ensure that the side surface is free of dust and grease before at-
taching the rubber pads.
Fig. 2: Rubber pads must be attached on the right side of the server
for installing the server upright
Proceed as follows when starting up the ZEISS Server:
1. Using the patch cable RJ45 S/FTP Cat5e, connect the server with
your local area network in which the server will be operated (Figure
3/1).
2. Connect the secondary circuit cable for the external power supply to
the ZEISS Server (Figure 3/2). Ensure that the connection is secure.
3. Connect the primary circuit cable to the power socket.
4. Start the server by pressing once on the "power" button (Figure 4/1).
5. Wait until the power symbol on the button glows blue or blue-cyan.
The server is now ready for use.
1

10 Instructions for the ZEISS Server function
EN_20_012_0043l
Fig. 3: View of the rear side of the server
Fig. 4: Power button (front)
Overview of the ZEISS Server operating statuses
Button status
Color
Server status
Description
Button is black
ZEISS Server is
off
-
Button is green
and flickering
ZEISS Server is
booting with
HDD access
Server is booting. Wait until
the boot process is finished.
Button is blue
ZEISS Server is
ready for opera-
tion
ZEISS Server is ready to be
operated
Button is blue/
cyan flickering
ZEISS Server is
ready for opera-
tion with HDD
access
ZEISS Server is ready for op-
eration –HDD is in use
Button is red
Temperature
warning
Switch off the ZEISS Server
and check the cooler and
fan vents. Wait until the
box has cooled down and
switch it on again. If the
warning reappears, please
call the hotline.
Button is red/
yellow flickering
Temperature
warning with
HDD access
Switch off the ZEISS Server
and check the cooler and
fan vents. Wait until the
box has cooled down and
switch it on again. If the
warning reappears, please
call the hotline.
1
2
1

Instructions for the ZEISS Server function 11
EN_20_012_0043l

System Industrie Electronic GmbH
Millennium Park 12
A-6890 Lustenau
T +43 / 5577 / 89900-0
F +43 / 5577 / 89901
FN Nr. 329733b Feldkirch
ISO9001 & ISO13485
www.sie.at
Carl Zeiss Vision GmbH
Turnstrasse 27
73430 Aalen
Germany
Phone: [phone]
Fax: [phone]
E-mail: service.vts.gl[email protected]
www.zeiss.com/vision
EN_20_012_0043l
2020-07-07
Specification subject to change