manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Abode
  6. •
  7. Kitchen & Bath Fixture
  8. •
  9. Abode AT1070 User manual

Abode AT1070 User manual

Other Abode Kitchen & Bath Fixture manuals

Abode Verla Monobloc AT1234 User manual

Abode

Abode Verla Monobloc AT1234 User manual

Abode Linear Monobloc AT1185 User manual

Abode

Abode Linear Monobloc AT1185 User manual

Abode Coniq-R AT2116 User manual

Abode

Abode Coniq-R AT2116 User manual

Abode Pico Monobloc AT1226 User manual

Abode

Abode Pico Monobloc AT1226 User manual

Abode Coniq-S AT2114 User manual

Abode

Abode Coniq-S AT2114 User manual

Abode Althia Monobloc AT1256 User manual

Abode

Abode Althia Monobloc AT1256 User manual

Abode Althia AT1259 User manual

Abode

Abode Althia AT1259 User manual

Abode Globe Professional AT2150-51 User manual

Abode

Abode Globe Professional AT2150-51 User manual

Abode Hex Monobloc User manual

Abode

Abode Hex Monobloc User manual

Abode AECRD2002 User manual

Abode

Abode AECRD2002 User manual

Abode Harrington Monobloc AT1229 User manual

Abode

Abode Harrington Monobloc AT1229 User manual

Abode Coniq-R AT2124 User manual

Abode

Abode Coniq-R AT2124 User manual

Abode Hex AT208 User manual

Abode

Abode Hex AT208 User manual

Popular Kitchen & Bath Fixture manuals by other brands

VIGO Matte Stone VG04001 manual

VIGO

VIGO Matte Stone VG04001 manual

Hans Grohe Zenio Metro 31811000 manual

Hans Grohe

Hans Grohe Zenio Metro 31811000 manual

Kohler Contra 26448T-4 installation instructions

Kohler

Kohler Contra 26448T-4 installation instructions

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Instructions for use and assembly instructions

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Instructions for use and assembly instructions

Wickes MONO SINK MIXER instruction manual

Wickes

Wickes MONO SINK MIXER instruction manual

Grohe ALLURE manual

Grohe

Grohe ALLURE manual

Oliveri Munich MU7063C installation instructions

Oliveri

Oliveri Munich MU7063C installation instructions

Graff PHASE E-6659-LM45W Instructions for assembly and use

Graff

Graff PHASE E-6659-LM45W Instructions for assembly and use

Lefroy Brooks ZU X1-2030 Installation, operating,  & maintenance instructions

Lefroy Brooks

Lefroy Brooks ZU X1-2030 Installation, operating, & maintenance instructions

Moen Show House TS514 Series installation guide

Moen

Moen Show House TS514 Series installation guide

Spectrum Brands Pfister F-WK1-1 manual

Spectrum Brands

Spectrum Brands Pfister F-WK1-1 manual

Moen Chateau 4904 instruction sheet

Moen

Moen Chateau 4904 instruction sheet

Kalia KONTOUR BF1288 Installation instructions / warranty

Kalia

Kalia KONTOUR BF1288 Installation instructions / warranty

Hans Grohe Axor Starck 10133 Series Installation instructions / warranty

Hans Grohe

Hans Grohe Axor Starck 10133 Series Installation instructions / warranty

DOCOL 016115 Series installation guide

DOCOL

DOCOL 016115 Series installation guide

Perrin & Rowe Mimas 4841 Installation & user guide

Perrin & Rowe

Perrin & Rowe Mimas 4841 Installation & user guide

Rohl Perrin & Rowe Georgian Bathroom U.3712LS Installation & user guide

Rohl

Rohl Perrin & Rowe Georgian Bathroom U.3712LS Installation & user guide

baliv KI-5070 manual

baliv

baliv KI-5070 manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.

Important Technical Data
Minimum operating pressure 0.3 bar (With
optional flow straightener) 0.5 bar (as supplied).
Maximum operating pressure 5.5 bar*
Maximum hot water temperature 70° *
Recommended hot water temperature 46°
Note: If these temperatures or pressures are
exceeded, even for short periods, damage can
result. In these instances a thermostatic mixing
or pressure reducing valve should be installed.
All Abode taps are either WRAS approved or
manufactured in accordance with recognised
European standards. Please ensure that your
Abode Kitchen mixer is fitted in accordance with
Local Water Byelaws.
These installation guidelines have been prepared for your
direction and you must exercise due care at all times. We do not
accept responsibility for problems that may occur through
improper installation. Whilst assembling the tap take care not to
accidentally loosen any screwed assemblies.
Abode is a registered trademark of Abode
(a division of Norcros Holdings Limited).
Manufacturers Product Reference
©Abode
11/2018
Abode Home Products Limited, Unit L, Zenith Park, Whaley Road, Barnsley, S75 1HT.
Tel: 01226 283434 Fax: 01226 282434 www.abode.eu
All errors and omissions excepted.
Propus Single Lever
5 Year warranty
Terms and Conditions
In the unlikely event that you should experience any
defect in the materials or workmanship of your new
Abode mixer within 5 years of purchase, the purchaser’s
sole remedy shall be the replacement (at the
manufacturer’s discretion) of all or any part of the
product that is defective. All working parts and valves are
guaranteed for a period of 5 years from purchase.
Decorative surface finishes and O-rings are guaranteed
for 1 year from the date of purchase provided that our
advice concerning care has been observed and no
scouring agents have been used. This is provided that the
mixer or tap has been used for normal domestic
purposes and that the care, installation and maintenance
instructions have been observed. The warranty extends
to the original purchaser only.
Marks, scuffs and scratches caused by improper
installation or accidental damage are not covered by this
guarantee. Neither are shade variations or any damage
or defect caused by incorrect installation or abuse of the
fitting.
As we are continuously improving and developing our
range of products, finishes & colours, in the event of a
valid claim, we may not be able to provide an identical
replacement for the defective product throughout the
guarantee period. Where an identical product is no
longer available, we will supply the nearest equivalent
from our then current product range. In assessing your
claim, we must be given the opportunity to inspect the
product as installed prior to removal. Any product
returns must be packaged as received and complete.
No other warranties, express or implied, are made,
including merchantability or fitness for a particular
purpose. Under no circumstances shall the manufacturer
be liable for any loss or damage arising from the
purchase, use or inability to use this product, or for any
special, indirect, incidental or consequential damages.
No liability is accepted for consequential damage to
other household fixtures, fittings or furnishings arising
from this claim, even if attached to the product. No
installer, dealer, agent or employee of Abode has the
authority to modify the obligations or limitations of this
warranty.
Care Instructions for your Kitchen Sink Mi er
To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of
warm water and a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry.
Any other cleaning action will invalidate your warranty.
If the mixertap has a diffuser it should be unscrewed and cleaned periodically in warm water.
Abrasive cleaners, scouring cleaners and acidic cleaners must not be used under any circumstances. Avoid contact with all
solvents (including chlorinated solvents, ketones or acetones as these may result in surface deterioration or etching). Also
avoid contact with any harsh household chemicals such as oven cleaners, drain cleaners, rust removers, paint strippers and
toilet bowl cleaners, bar keepers friend or Brasso.
Please leave these instructions for your customer.
Parts and Contents
Key
Description
Qty
A Tap body 1
B Base plinth 1
C Upper seal 1
D Fixing stud 2
E
White triangular stabilizer
( or stainless steel sinks only)
1
F Rubber gasket 1
G Metal horseshoe 1
H Fixing nut 2
I Hot / cold water lexible tail
pipes (with integral NRV) 2
Installation Instructions:
Preparation
Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any
remaining solder, swarf or impurities from your system. Failure to carry out this simple procedure could cause problems or
damage to the workings of the mixertap.
We strongly recommend installing particle filters and isolation valves to both the hot and cold feed pipes in an accessible
position. This will help to prevent premature failure of the valves and ease any future maintenance.
All parts should be removed from their packaging and inspected for any transport damage prior to installation.
Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold taps in the
house and allow the water to run until the cold-water storage tank and pipes are fully empty. Please note, the hot water
storage cylinder (if applicable) will always remain full.
This mixertap requires a 35mm∅ tap hole, if replacing an existing tap, remove the tap & clean the end of the feed pipes using
wire wool the tap hole area should be free from dirt and sealant.
Loosely position the tap and tail pipes to check if any alteration to the existing pipework is required, if this is the case do this
now.
Installation
1. Screw studded rods (D) into the base of the tap (A).
2. Place the upper seal ( ) into the base plinth (B) then place the base plinth (B) onto the bottom of the tap (A).
3. Screw the hot & cold water tail pipes (I) into the base of the tap (A) with the handle positioned to the right as
shown the cold flexible hose will be at the rear of the tap.
4. Place the mixertap (A), base plinth (B) and seal ( ) onto the sink/worktop, passing the tail pipes (I) and studded
rods (D) through the tap hole.
5. Pass the triangular stabiliser (E), lower gasket (F) and then the metal horseshoe (G) over the studded rods (D) and
around the flexible tail pipes (I)
6. Fasten the fixing nuts (H) securely onto the fixing studs (D) to fix the tap (A) into its correct location.
7. onnect the hot and cold tail pipes (I) to the water mains using ½” BSPx15mm compression fittings. Note: Non-
return valves will be pre-inserted into tail pipes (I).
After installation
Once you have visually checked the new fittings and connections, ensure that all taps are closed except the new mixer tap
which should be left open. Turn on the water supply at the mains stop cock. As the system starts to refill, check carefully for
leaks. Once you are fully satisfied that there are no leaks, turn on the water heating.
lean the tap to remove any marks created during installation as instructed then place the cloth bag that has been provided to
protect the tap until it is ready for use.
To increase the flow rate for this product substitute the optional spout flow straightener with the standard aerator which is
attached as supplied.