Ace Sports Maxxam 150 2R User manual

150 2R
ACE-Maxxam-002-02-2007
239 County Road 4435
Brundidge, AL 36081
www.acesportsonline.com
P: 1-888-562-9ACE
F: 1-888-562-8ACE
Buggy Service Manual

FOREWORD
This service manual has been specially prepared to provide all the necessary information for the
proper maintenance and repair of the MAXXAM.
The MAXXAM ts the needs of a wide variety of kart users above 16 years old. Those who will
be servicing this kart should carefully review this manual before performing any repair or services.
All information, illustrations photographs and speci cations contained in this manual are based on
the latest product information available at the time of publication. Due to improvements or other
changes, there may be some discrepancies in this manual. Therefore, if newest information is
requested in the future, please contact the local distributor.
The distributor reserves the right to make production changes at any time, without notice and without
incurring any obligation to make the same or similar changes to vehicles previously built or sold.
A.C.E. S PORTS
239 County Road 4435
Brundidge, AL36010
Phone: [phone]ACE
Fax:[phone]ACE

GENERAL INFORMATION
PERIODIC MAINTENANCE AND TUNE-UP PROCEDURES
ENGINE
LUBRICATION SYSTEM INSPECTION AND SERVICING
FUEL SUPPLY SYSTEM INSPECTION AND SERVICING
TRANSMISSION CONPONENTS
ELECTRICAL STARTING SYSTEM
REDUCTION MECHANISM
CONTROLLING MECHANISM
BELT DRIVEN CVT MECHANISM INSPECTION AND SERVICING
CLUTCH
DRIVEN BELT PULLEY
REAR TRANSMISSION MECHANISM INSPECTION AND SERVICING
ELECTRICAL SYSTEM
PRIMARY COIL
IGNITION SYSTEM INSPECTION AND SERVICING
CHASSIS
WIRING DIAGRAM
INDEX
1
5
9
24
28
33
34
37
39
40
44
46
49
54
56
60
64
70
71

1
GENERAL INFORMATION
MODEL IDENTIFICATION
FRAME NUMBER
The frame number or VIN is stamped under the seat on the frame cross member and on a sticker
behind the seat.
ENGINE NUMBER
The engine number is located on the lower front left side of the engine case.
FUEL AND OIL RECOMMENDATIONS
%HVXUHWRXVHWKHVSHFL¿HGIXHODQGRLO
FUEL
Gasoline should be 85 to 95 octane or higher.
Unleaded gasoline is recommended.
ENGINE OIL
High-grade 10W-40 motor oil should be used.
BREAK-IN PROCEDURE
)RUWKH¿UVW KRXUVRIULGLQJGRQRWH[FHHGWKURWWOH
• Vary engine speed for the ¿rst 5 hours.
• Never hold engine at full throttle for long periods of time.

2
SPECIFICATIONS
DIMENSIONS
Overall length 2075mm (87.7 in.)
Overall width 1235mm (48.6 in.)
Overall height 1400mm (55.1 in.)
Wheelbase 1450mm (57 in.)
Front Track 1060mm (47.1 in.)
Rear Track 1000mm (39.4 in.)
Ground Clearance 130mm (5.1 in.)
ENGINE
Type Forced air-cooled, 4-stroke
Engine capacity 150cc
Bore x stroke 57.4 x 57.8
Corrected Compression Ration 9.2:1
Carburetor PD25J
Output Power 9HP/7500 rpm
Maximum Torque [N.m(r/min)-1] 8.0/4000-4500
Starting Electric
Ignition CDI
Lubrication Force & Splash
Transmission Automatic CVT
CAPACITIES
Load 1 rider or 90kg/198Ibs
Fuel tank 7L/1.54Gal
Starting 5s
Climbing 20-25°
CHASSIS
Front Brake Hydraulic disc/left foot control
Rear Brake Hydraulic disc/left foot control
Front Tire 20 x 7.0-8
Rear Tire 22 x 10-10
Suspension-Front Dual A-arm with 1.8” (45mm) of travel
Suspension-Rear Spring over shock with 2.4” (60mm) of travel
Brake Track 7m@20mph
Top Speed 30mph (or limited as customers require)


:(,*+7
'U\:HLJKW NJOEV
7,5(35(6685(
)URQW 103VL68.95N3DFP70NJIFP
5HDU 103VL68.95N3DFP70NJIFP
:$55$17<
7KHVSHFL¿FDWLRQVDUHVXEMHFWWRFKDQJHZLWKRXWQRWLFH

4
LOCATION OF PARTS
DRIVE CHAIN
DRIVE CHAIN

5
PERIODIC MAINTENANCE
AND TUNE-UP PROCEDURES
PERIODIC CHECK AND SERVICES
The maintenance intervals in the following table are based upon average riding conditions. Riding in
unusually dusty areas requires more frequent servicing.
Items Needing
Servicing
Initial Service
Àrst week)
Monthly Quarterly Yearly
Tire pressure/wear II
Brake performance II
Tightness of screws II
Air cleaner CC I
Carburetor IA C
Spark plug C, A
Drive chain I I C, A, L
%UDNHÀXLG I
Replace gearbox oil IR
Chassis C, L L
Fuel switch/fuel tank C
Battery II
Engine oil R
Valve clearance of engine A
A: Adjust C: Clean I: Inspect, clean or replace if necessary L: Lubricate R: Replace
MAINTENANCE AND TUNE-UP PROCEDURES
Descriptions of the servicing procedures for each item in the Periodic Maintenance table.
SPARK PLUG
• Clean up the carbon around the spark plug to prevent it from dripping into the cylinder when
being removed.
• Remove the spark plug
• If the spark plug is too tight to remove, spray rust inhibiter on the spark plug washer and the
thread. After soaking for a few minutes, the spark plug should easily unscrew.
• Clean up any dirt and carbon accumulation on the spark plug with a steel brush or a blade.
• Inspect the spark plug gap, it should be about 0.6 ~ 0.7mm.
• When the carbon accumulation and wear of the spark plug are too severe, replace the spark plug
with one of the same speci¿cation.
Note: The spark plug should generally be serviced when the engine is cold.

6
TIRE PRESSURE/WEAR
Check the tire pressure every time the kart is ridden. The tire pressure is very important for the
stability of the ride.
Tire Pressure
Front 10 psi 68.95kPa/cm20.70kgf/cm2
Rear 10 psi 68.95kPa/cm20.70kgf/cm2
BRAKE PERFORMANCE
• Always check that there is plenty of brake uid in the brake uid reservoir.
• Check that the rear brake pads are in good condition.
• Check the brake rotor for abnormal wear.
AIR CLEANER
If the air cleaner is clogged with dust, performance will be severely decreased, if left
unserviced, engine damage can occur. Check and clean in the following appropriate manner.
Paper Filter Maintenance
• Remove the air cleaner from its housing
•T 
• Replace the element if it is wrinkled or torn
Foam Filter Maintenance

• Wash in non- ammable cleaning solvent
• Install the element back into the air box.
Note: Clean after every 20 hours of use, or more often if used in a dusty environment.
Caution! Before and during cleaning, inspect the element for
tears. A torn element must be replaced. Make sure the element
is seated properly and no foreign material can pass by it.
THROTTLE CABLE ADJUSTMENT
• Conditioning nut, bolt from the adjustment nut goes farther, the greater the degree of throttle
opening, the smaller the contrary. The greater the degree of throttle opening, the higher the Idle
adjustment nut adjustment nuts

7
CHASSIS NUTS AND BOLTS
Always pay attention to the kart's nuts and bolts. Some loosening after use is normal. Check to
ensure that all nuts and bolts are tight.
Torque Tightening Chart
Bolt Conventional Marked Bolt 8.8 Marked Bolt
Diameter N.m Kg.m Ib-ft N.m Kg.m Ib-ft
4 1 ~ 2 0.1 ~ 0.2 0.7 ~ 1.5 1.5 ~ 3 0.15 ~ 0.3 1.0 ~ 2.0
5 1 ~ 4 0.2 ~ 0.4 1.5 ~ 3.0 3 ~ 6 0.3 ~ 0.6 2.0 ~ 4.5
6 4 ~ 7 0.4 ~ 0.7 3.0 ~ 5.0 8 ~ 12 0.8 ~ 1.2 6.0 ~ 8.5
8 10 ~ 16 1.0 ~ 1.6 7.0 ~ 11.5 18 ~ 28 1.8 ~ 2.8 13.0 ~ 20.0
10 22 ~ 35 2.2 ~ 3.5 16.0 ~ 25.5 40 ~ 60 4.0 ~ 6.0 29.0 ~ 43.5
12 35 ~ 50 3.5 ~ 5.5 25.5 ~ 40 70 ~ 100 7.0 ~ 10.0 50.5 ~ 72.5
14 50 ~ 80 5.0 ~ 8.0 36.5 ~ 58 110 ~ 160 11.0 ~ 16.0 79.5 ~ 115.5
16 80 ~ 130 8.0 ~ 13.0 58 ~ 94 170 ~ 250 17.0 ~ 25. 123.0 ~ 181.0
18 130 ~ 190 13.0 ~19.0 94 ~ 137.5 200 ~ 280 20 ~ 28.0 144.5 ~ 202.5
FUEL SWITCH (PETCOCK)
• Periodically clean the petcock externally with grease remover and water.
• Check for any leaks or seeping fuel.
• Replace the petcock if there are any leaks found.
This vehicle has a manually operated fuel valve . There are three positions.
“ON” position
The normal operating position for the fuel valve lever is the “ON” position. In this position, fuel will
ÀRZWRWKHFDUEXUHWRr.
“RES” position
If the fuel level in the fuel tank becomes too low for the engine to operate with the fuel valve lever
in the “ON” position, turn the lever to the “RES” position to use the reserve fuel supply, and refuel
as soon as possible.
“OFF” position
The closing position for the fuel valve is the “OFF” position.
When the vehicle is not in use, always make sure the petcock is in the “OFF” position.
Note: ,QVSHFWWKH¿UVWZHHNDQGWKHQHYHU\PRQWKWKHUHDIWHU.


),1$/*($52,/
7RFKHFNOHYHOUHPRYHOHYHOVFUHZRQWKH
OHIWUHDUHQJLQHFDVH
7RGUDLQRLOUHPRYHWKHGUDLQSOXJDWWKH
UHDUERWWRPRIWKHHQJLQHFDVH,WLV
UHFRPPHQGHGWRZDUPWKHHQJLQHIRU
PLQXWHVRUPRUHbefore GUDLQLQJ¿QDOgearRLO
)LQDOGULYHFDSDFLW\
PO ZHLJKW
(1*,1(2,/
5HPRYHWKHGUDLQSOXJIURPWKHOHIWVLGHERWWRPRIWKHHQJLQH
'UDLQLQWRRLOSDQIRUGLVSRVDO
5HPRYHWKHODUJHFDSRQWKHULJKWERWWRPRIWKHHQJLQHDQGUH
PRYHWKHVFUHHQ
:DVKWKHVFUHHQZLWKFOHDQLQJVROYHQWDQGUH¿WPDNLQJVXUHWKH
2ULQJLVVWLOOLQJRRGFRQGLWLRQ Replace screen and drain plug.
5H¿OOWKHHQJLQHZLWK:HQJLQHRLODQGUXQIRUPLQXWHV
&KHFNRLOOHYHORQWKH¿OOHUFDSVWLFNWRDVVXUHSURSHUOHYHO
7KHFDSQHHGVWREHVFUHZHGLQIRUDSURSHUUHDGLQJ
&+$66,6
*UHDVHFKDVVLVEXVKLQJVDQGEHDULQJVZLWKJUHDVHTXDUWHUO\WR
DVVXUHVPRRWKRSHUDWLRQDQGH[WHQGHGOLIWRIWKHEXVKLQJVDQGWKH
FRPSRQHQWV,IXVHGLQH[WUHPHZHWDQGPXGG\FRQGLWLRQVRUGXVW\
FRQGLWLRQVJUHDVLQJLVUHFRPPHQGHGPRUHRIWHQ
&$5%85(725
5HIHUWR&DUEXUHWRUVHFWLRQ
9$/9(&/($5$1&(
5HIHUWR(QJLQHVHFWLRQ
1RWH,QVSHFWPRQWKO\DQGFKDQJHTXDUWHUO\
1RWHZHLJKWJHDURLOLVUHFRPPHQGHGLQWKH¿QDOGULYHFDVH+RZHYHULQ
H[WUHPHFROGZHDWKHUFRQGLWLRQV\RXPD\QRWLFHWKDWWKHNDUWLVKDUGWRSXVK,I
WKDWLVWKHFDVHXVHOLJKWHUYLVFRVLW\RLOVXFKDVZHLJKWRUHTXLYDOHQWPRWRU
F\FOHWUDQVPLVVLRQÀXLG
1RWH,QVSHFWEHIRUHHDFKXVH&KDQJHPRQWKO\

9
ENGINE
ENGINE COMPONENTS INSPECTION AND SERVICING
ENGINE COMPONENTS AND CRANK CONNECTING ROD
MECHANISM INSPECTION AND SERVICING
ENGINE COMPONENTS: CYLINDER
CYLINDER REMOVAL
The removal can be done on the vehicle body.
• Remove cylinder head.
• Remove cylinder.
• Remove cylinder gasket, bolts
• Clean cylinder gasket and remove any debris.
CYLINDER INNER WALL WEAR INSPECTION
Use a bore diameter dial gauge to measure the degree of wear.
The measure point is divided into three sectional planes in the axial direction: upper, middle and
lower; measure every plane each time on the mutually perpendicular directions (X, Y), the mea-
sured least dimension is the cylinder bore; at the most upper position measured is the largest
diameter, and the lowest position measured is the smallest diameter, their difference is the cylin-
dricity of the cylinder. At the same cross section, measure the difference of diameter between two
points mutually perpendicular; which is the circularity of the cylinder.
In the situation without a dial gauge, a feeler gauge can be used to make relativity measurement.
Put a new piston into the cylinder, and use the feeler gauge to measure the gap between the
piston skirt and the cylinder wall. Then ¿gure out the abrasion loss of the cylinder. If the circu-
larity of the cylinder exceeds the limit, then a cylinder reboring machine should be used to rebore
the cylinder, and enlarge its diameter by 0.5mm or 1.00mm, then ¿t the piston and piston ring
which size are also enlarged. If the wear is too severe and cannot be reworked, then a new cylin-
der should be installed.
Cylinder bore 57.4mm
Cylindricity 0.05mm
Circularity 0.05mm
Caution!
Do not damage the cylinder area. Make sure not to drop anything,
including cylinder gasketmaterial,into the crankcase.
In order to make the measuring point perpendicular with the bore axis of the cyl-
inder, and to ensure the precision of the measurement, the bar of the gauge can
be slightly swung in the direction of the gauge bar, and take the smallest reading
number as the result.


&5$1.&211(&7,1*52'0(&+$1,603,67216(7
3,67213,1,163(&7,21$1'6(59,&,1*
,QVHUWWKHSLVWRQSLQKRUL]RQWDOO\LQWRWKHSLVWRQSLQKROHDQGLQVSHFWWKHFOHDUDQFHEHWZHHQSLV
WRQDQGSLVWRQSLQ
6HUYLFH/LPLW PP
,IWKHIUHHSOD\LVWRRPXFKWKHZRUQFRQGLWLRQRISLVWRQSLQDQGSLVWRQSLQKROHPXVWEHLQVSHFWHG
UHVSHFWLYHO\
0HDVXUHWKHH[WHUQDOGLDPHWHURISLVWRQSLQ
6HUYLFH/LPLW PP
,IWKHUHVXOWLVOHVVWKDQWKH6HUYLFHOLPLWLWVKRXOGEHUHSODFHG
$IWHUUHSODFHPHQWFKHFNWKHFOHDUDQFHEHWZHHQSLVWRQSLQDQGSLVWRQSLQKROHDQGPDNHVXUHLW
FRPSOLHVZLWKWKHUHTXLUHGPHDVXUHPHQW
0HDVXUHWKHLQQHUGLDPHWHURISLVWRQSLQ
6HUYLFH/LPLW PP
,IWKHUHVXOWLVPRUHWKDQWKHVHUYLFHOLPLWLWVKRXOGEHUHSODFHG
$IWHUUHSODFHPHQWFKHFNWKHFOHDUDQFHEHWZHHQWKHKROHVRIWKHSLVWRQSLQDQGPDNHVXUHLWFRP
SOLHVZLWKWKHUHTXLUHGPHDVXUHPHQW
3,67215,1*6,163(&7,21$1'6(59,&,1*
,QVSHFWWKHSLVWRQULQJIRUÀDZVVHULRXVZHDURUVHULRXVFRQJOXWLQDWLRQHWF,IWKHUHLVLWVKRXOG
EHUHSODFHG
,IWKHSLVWRQULQJ¶VODWHUDOFOHDUDQFHDQGQRWFKFOHDUDQFHDUHWRRODUJHRUWRRVPDOOLWZLOOFDXVH
PDOIXQFWLRQVVRLWPXVWEHPHDVXUHG
0HDVXUHWKHFOHDUDQFHRIWKHSLVWRQULQJLQWKHSLVWRQULQJJURRYH7KLVFOHDUDQFHLVWKHSLVWRQ
ULQJ¶VODWHUDOFOHDUDQFH
)LUVW5LQJ PP
6HFRQG5LQJ PP
&211(&7,1*52'(1',163(&7,21
3XWWKHSLVWRQSLQDQGEHDULQJLQWRWKHFRQQHFWLQJURGHQGLQVSHFWWKHGHJUHHRIWLJKWQHVVRIWKH
SLVWRQSLQLQFRQQHFWLQJURGHQG
0HDVXUHWKHLQQHUGLDPHWHURIWKHFRQQHFWLQJURGHQG
6HUYLFH/LPLW PP
:KHQWKHDEUDVLRQRIWKHERUHH[FHHGVWKHOLPLWDWLRQLWVKRXOGEHUHSODFHG


3,67215,1*66(783
%HIRUHVHWWLQJXSDSSO\RLORQHDFKSLVWRQULQJWKHQHQODUJHSLVWRQULQJVDWWKHVDPH
WLPHSXWWKHPRQWKHSLVWRQDQGPRYHGRZQZDUGVJUDGXDOO\XQWLOSLVWRQULQJVIDOOLQWRWKH
ULQJJURRYH
3,67216(7,167$//$7,21
5HPRYHWKHJDVNHWDWWDFKHGWRWKHFUDQNFDVH
0RXQWSLVWRQRQWRWKHVPDOOHQGRIWKHFRQQHFWLQJURG
0RXQWSLVWRQSLQDQGSLVWRQSLQFOLS
$SSO\RLORQWKHSLVWRQSLQWROXEULFDWHLW
&5$1.&211(&7,1*52'6(7
7KHFRQQHFWLQJURGLVWKHFRPSRQHQWWKDWOLQNVWKHSLVWRQDQGFUDQN
7KHSLFWXUHVKRZVWKHVWUXFWXUHDQGDVVHPEOLQJUHODWLRQVRIWKHFUDQN
FRQQHFWLQJURGFRPSRQHQW

&5$1.&$6($1'&5$1.6+$)75(029$/
%HIRUHUHPRYLQJWKHFUDQNFDVHDQGFUDQNVKDIWIROORZWKHVHSURFHGXUHV
5HPRYHWKHHQJLQH
5HPRYHWKHF\OLQGHUFRYHU
5HPRYHWKHF\OLQGHU
5HPRYHWKHSLVWRQ
5HPRYHWKHGULYHSODWHDQGWKHGULYHQSODWH
5HPRYHWKH$&JHQHUDWRU
5HPRYHWKHVWDUWLQJPRWRU
5HPRYHWKHRLOSXPS
7KHQUHPRYHWKHFDPFKDLQWHQVLRQHUEROW5HPRYHWKH
FDPFKDLQWHQVLRQHU
8VHVSHFLDOWRROVWRUHPRYHWKHVWDUWLQJGULYHQJHDU
7KHWRSRIWKHSLVWRQPDUNHGZLWK³,1´VKRXOGEHPRXQWHGWRZDUGVWKHGLUHFWLRQRI
WKHLQOHWSRUWLIWKHPDUNLV³(;´WKHQLWVKRXOGEHPRXQWHGWRZDUGVWKHGLUHFWLRQRI
WKHH[KDXVWSRUW
&RYHUWKHFUDQNFDVHSRUWZLWKDSLHFHRIFORWKWRNHHSWKH
SLVWRQFOLSIURPGURSSLQJLQWRWKHFUDQNFDVH


5HPRYHWKHFUDQNFDVHSRVLWLRQLQJEROWV
6HSDUDWHWKHULJKWFUDQNFDVHDQGWKHOHIWFUDQNFDVH
5HPRYHWKHJDVNHWDQGWKHGRZHOSLQV
5HPRYHWKHFUDQNVKDIWIURPWKHFUDQNFDVH
7DNHRXWWKHFDPFKDLQ
5HPRYHWKHJDVNHWRQWKHFUDQNFDVHMRLQWIDFH
EHFDUHIXOWRQRWGDPDJHWKHMRLQWIDFH
5HPRYHWKHRLOVHDOIURPWKHOHIWFUDQNFDVH
5HPRYHWKHRLOVHDOIURPWKHULJKWFUDQNFDVH
%HFDUHIXOQRWWRGDPDJHWKHMRLQWIDFH

13
CRANKSHAFT AND CRANKCASE INSPECTION
• Replace the whole set of the crankshaft if serious wear is found while inspecting. Measurethe
axial trend clearance of the big end of the connecting rod.
• When measuring, put the large end of the connecting rod close to the crank, and insert the feeler
gauge between the other side and the crank, for the correct end play.
Service Limit 0.55mm
• Measure the radial trend (X,Y) clearance of the big end of the connecting rod.
Service Limit 0.05mm
• Measure the main shaft journal jump of the crankshaft.
If this measurement is too great, it will cause the engine to shake abnormally, shortening the
life of the engineIt must be examined carefully when inspecting.
Service Limit 0.10mm(A=90)
0.10mm(B=105)
• Examine if there is any loose, or unusual sound when the crank journal bearing turns. If there is,
the whole set should be changed.
• After cleaning the crankcase, inspect to see if there is any damage.
• Inspect whether the joint face of the crankcase is smooth and clean. While reassembling, notice if it
will affect the sealing performance between the left and right crankcase.
$IWHUWKHDERYHLQVSHFWLRQLIWKHFUDQNFDVHKDVVRPHVXUIDFHGDPDJHXVHRLOVWRQHWRrefinish it.
If damage is too severe, replace the cover.
CRANKSHAFT AND CRANKCASE INSTALLATION
• Mount the crankcase oil seal.
• Put the cam chain into the left crankcase.
• Put the crankshaft into the left crankcase.
Because the right and left crankcase axle hole must be concentric, they
should be replaced at the same time.
Pay attention to avoid damaging the oil seal with the cam chain.


0RXQWWKHQHZGRZHOSLQVDQGJDVNHWRQWKHOHIWFUDQNFDVH7KHQMRLQWKHULJKWFUDQNFDVHDQG
OHIWFUDQNFDVHWRJHWKHU
7LJKWHQWKHFUDQNFDVHSRVLWLRQLQJEROWV
7LJKWHQLQJ7RUTXH OEVP
0RXQWWKHVWDUWLQJGULYHQJHDU.
0RXQWWKHFDPFKDLQWHQVLRQHU.
0RXQWWKHQHZ2ULQJRQWKHFDPFKDLQWHQVLRQHUEROW
$SSO\VRPHRLORQWKH2ULQJ
7LJKWHQWKHFDPFKDLQWHQVLRQHUEROW
9$/9(0(&+$1,60,163(&7,21$1'6(59,&,1*
7KHSLFWXUHVKRZVWKHFRPPRQYDOYHWUDLQRIDIRXUVWURNHHQJLQH7KLVLVDNLQGRIRYHUKHDGYDOYH
WUDLQLWVLQWDNHSRUWH[KDXVWSRUWFDPVKDIWDUHDOOORFDWHGLQWKHF\OLQGHUKHDGWKHYDOYHVERWWRPXS
RYHUWKHFRPEXVWLRQFKDPEHU
*(1(5$/,1752'8&7,21
7KHIRXUVWURNHHQJLQHFRPSOHWHVLWVIRXUVWURNHZLWKRQHSLVWRQVWURNH
,QWDNHVWURNH
&RPSUHVVLRQVWURNH
([SDQVLRQVWURNH
([KDXVWVWURNH
7KH2ULQJPXVWEHPRXQWHGLQWKHJURRYH


9$/9(&/($5$1&($'-8670(17
9DOYHFOHDUDQFHLVDQLPSRUWDQWWHFKQLFDOSDUDPHWHULQWKH
YDOYHWUDLQ,QRUGHUWRenable the engine to run properly,
HVSHFLDOO\ZKHQWKHHQJLQHLVRYHUKHDWHGRULQFROG
FRQGLWLRQVDFHUWDLQFOHDUDQFHPXVWEHNHSW7KLVFOHDUDQFH
LVFDOOHGYDOYHFOHDUDQFH:KHQWKHHQJLQHLVUXQQLQJWKH
YDOYHFOHDUDQFHPXVWQRWEHWRRELJRUWRRVPDOO
• 5HPRYHWKHF\OLQGHUKHDGFRYHU
•7XUQWKHFRROLQJIDQFORFNZLVHXQWLOWKHPDUNRIWKHWLPLQJGULYHVSURFNHWRQWKHFDPVKDIWLVDWWKH
WRSGHDGFHQWHUDQGWKH³7´V\PERORURWKHUPDUNRIWKHPDJQHWRÀ\ZKHHODOLJQVWRWKHFUDQN
FDVHPDUN
•:KHQDGMXVWLQJORRVHQWKHORFNQXWVDGMXVWWKHEROWVZLWK
DYDOYHDGMXVWLQJZUHQFK.WKHQWXUQHGFORFNZLVHWKHYDOYH
FOHDUDQFHGHFUHDVHV WKHQWXUQHGFRXQWHUFORFNZLVH
WKHYDOYHFOHDUDQFHLQFUHDVHV3XWDIHHOHUJDXJHZLWKVSH
FL¿FVL]HVEHWZHHQWKHYDOYHDQGURFNHWWRFKHFNIRUFRUUHFW
FOHDUDQFH
•7DNHRXWWKHIHHOHUJDXJHWLJKWHQWKHORFNQXWVDQGWKHQLQVSHFWWKHYDOYHFOHDUDQFHDJDLQ
9DOYH&OHDUDQFH aPP
,QVSHFWLRQDQGDGMXVWPHQWVKRXOGEHGRQHLQ
FRROFRQGLWLRQVEHORZR&
7KHFUDQNVKDIWVKRXOGURWDWHRUWKHH[KDXVWSRUWPD\QRWEHDGMXVWHG
6RPHWLPHVZKHQWLJKWHQLQJWKHORFNQXWVWKHFOHDUDQFHZLOOFKDQJH
VRLWPXVWEHUHFKHFNHGIRUWKHSURSHUFOHDUDQFH


&$06+$)7
7KHFDPVKDIWLVthePDLQGULYLQJXQLWRIWKHYDOYHWUDLQ7KHDLULQOHWFDPWKHH[KDXVWFDPDQGWKHFDP
MRXUQDODUHRQWKHVKDIW,WcausesWKHLQWDNHDQGH[KDXVWYDOYHWRRSHQDQGFORVHDWWKHFRUUHFWWLPH
:HDUWRWKHFDPVKDIWZLOODIIHFWHQJLQHSHUIRUPDQFHDQGFDXVHH[FHVVLYHQRLVH
&$06+$)75(029$/
/RRVHQYDOYHFRYHUEROWVDQGUHPRYHFRYHU
5HPRYHWKHFDPFKDLQWHQVLRQDOEROWFDSDQGUHPRYHWKH2ULQJ
7LJKWHQWKHFDPFKDLQWHQVLRQHUE\DGMXVWLQJEROWFORFNZLVH
7XUQWKHÀ\ZKHHOFRXQWHUFORFNZLVHWRPDNHWKH³7´PDUNRQWKH
À\ZKHHODOLJQZLWKWKHPDUNRQWKHFUDQNFDVH:KHQWKHKROHRQ
WKHFDPFKDLQWLPLQJGULYHFKDLQZKHHOLVXSLWVKRXOGEHDWWKH
WRSGHDGFHQWHU
5HPRYHWKHF\OLQGHUKHDGSRVLWLRQLQJEROW
5HPRYHWKHFDPVKDIWKROGHUEROWFDSDQGZDVKHU
5HPRYHWKHFDPVKDIWKROGHUDQGGRZHOSLQ
5HPRYHWKHFDPFKDLQZKHHOIURPWKHFDPFKDLQDQGUHPRYHWKH
FDPVKDIW
&$06+$)7,163(&7,21
,QVSHFWWKHFDPVKDIWEHDULQJVIRUSOD\.IIWKHUHLV too much play,UHSODFHWKHZKROHVHW
,QVSHFWFDPVXUIDFHIRUGDPDJH
0HDVXUHWKHKHLJKWRIWKHFDP
,QOHW&DP PP
([KDXVW&DP PP