Acrosser Technology ANR-DNV3N3-8C User manual

ANR-DNV3N3-8C
User Manual
Acrosser Technology Co., Ltd.
www.acrosser.com
ANR-DNV3N3-8C
Networking 1U Rackmount
• Intel®Denverton®AtomC3758SoC
• 8xGbECopper
• 4x10GbEFibber

ANR-DNV3N3-8C
2Acrosser Technology Co., Ltd.
To read this User Manual on your smart phone, you will have to install an
APP that can read PDF le format rst. Please nd the APP you prefer from
the APP Market.
Ver: 110-001
Date: Dec. 8, 2020
Disclaimer
For the purpose of improving reliability, design and function, the information in this document
is subject to change without prior notice and does not represent a commitment on the part of
Acrosser Technology Co., Ltd.
In no event will Acrosser Technology Co., Ltd. be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or documentation,
even if advised of the possibility of such damages.
Copyright
This document contains proprietary information protected by copyright. All rights are reserved.
No part of this manual may be reproduced by any mechanical, electronic, or other means in
any form without prior written permission of Acrosser Technology Co., Ltd.
Trademarks
The product names appear in this manual are for identication purpose only. The trademarks
and product names or brand names appear in this manual are the property of their respective
owners.
Purpose
This document is intended to provide the information about the features and use of the product.
Audience
The intended audiences are technical personnel, not for general audiences.

ANR-DNV3N3-8C
3www.acrosser.com
Table of Contents
1. System Introduction ...................................................................... 5
1.1. Specications ............................................................................................................. 5
1.2. Package Contents ...................................................................................................... 7
1.3. System Dissection...................................................................................................... 8
1.3.1. Dimensions ..................................................................................................... 8
1.3.2. Front I/O Panel................................................................................................ 9
1.3.3. Rear I/O Panel ................................................................................................ 9
2. Components Assembly ............................................................... 10
2.1. HDD Installation........................................................................................................ 10
2.2. NIM Module Insertion ............................................................................................... 14
2.3. Rack Installation ....................................................................................................... 17
3. BIOS Settings ............................................................................... 18
3.1. Main Setup ............................................................................................................... 18
3.2. Advanced Setup ....................................................................................................... 20
3.2.1. Advanced Setup: OnBoard Bypass Controller .............................................. 20
3.2.2. Advanced Setup: W83627DHG Super IO Conguration .............................. 21
3.2.3. Advanced Setup: W83627DHG HW Monitor ................................................ 22
3.2.4. Advanced Setup: Serial Port Console Redirection........................................ 24
3.2.5. Advanced Setup: Network Stack Conguration ............................................ 26
3.2.6. Advanced Setup: CSM Conguration ........................................................... 27
3.2.7. Advanced Setup: USB Conguration ............................................................ 28
3.3. IntelRCSetup ............................................................................................................ 29
3.3.1. IntelRCSetup: Processor Conguration ........................................................ 29
3.3.2. IntelRCSetup: South Bridge Chipset Conguration ..................................... 30
3.3.3. IntelRCSetup: SATA Port .............................................................................. 31
3.3.4. IntelRCSetup: M.2 SATA Port........................................................................ 31
3.4. Security Setup .......................................................................................................... 32
3.5. Boot Setup................................................................................................................ 33
3.6. Save & Exit Setup..................................................................................................... 34
4. Software Installation and Programming Guide ........................ 35
4.1. Introduction............................................................................................................... 35
4.1.1. Environment .................................................................................................. 35
4.1.2. GPIO ............................................................................................................. 35
4.1.3. Watchdog ...................................................................................................... 35
4.1.4. LAN Bypass Subsystem................................................................................ 35
4.2. File Descriptions....................................................................................................... 36

ANR-DNV3N3-8C
4Acrosser Technology Co., Ltd.
4.2.1. GPIO/Watchdog/LAN Bypass Subsystem..................................................... 36
4.3. API List and Descriptions ......................................................................................... 36
4.3.1. GPIO ............................................................................................................. 36
4.3.2. Watchdog ...................................................................................................... 37
4.3.3. LAN Bypass Subsystem................................................................................ 37
4.3.4. Notes............................................................................................................. 39
5. FAQ ............................................................................................... 40
Q 1. Where is the serial number located on my system?................................................. 40

ANR-DNV3N3-8C
5www.acrosser.com
1. System Introduction
The ANR-DNV3N3-8C networking product is based on Intel Atom®C3758 SoC,
powerful enough for SD-WAN or Universal CPE applications.
This product provides a compact but powerful system capability by supporting 8x
GbE copper LANs and 4x 10G ber networks(SFP+). In the system design, 3x 2.5-
inch HDD/SSD and one CFast card slot are available for storage in an 1U rackmount
chassis.
1.1. Specifications
(Specications are subject to change without notice.)
General
Thermal Solution • PWM Smart Cooling Fans
CPU • Intel®Denverton®C3758 8 cores, 2.1GHz
Memory • 2x U-DIMM DDR4
BIOS • Support Console Re-direction
• Support Bypass Setting
Scenario Normal Bypass
SYS (ON) V
SYS (OFF) V
WDT (Timeout) V
PWR (Lost) Remained prior status
• Support PXE boot from all RJ-45 Coppers
Network Interface
Ethernet (on-board) • 8x GbE, 4 SFP+
• Intel i211, LAN[1: 8]
• SoC embedded SFI x4, SFP+[1:4]
Storage
SATA • 3x SATA socket and 3x 2.5” HDD bay
CFast • 1x CFast socket

ANR-DNV3N3-8C
6Acrosser Technology Co., Ltd.
I/O
Front Panel • 2x USB 3.0
• 3x SYSTEM LED
• 1x RESET Button
• 1x RJ-45-console
• 8x GbE RJ-45 Copper LAN[1: 8]
• 4x SFP+(10G Fiber)
• 1x Acrosser swappable Exp. NIM.
Rear Panel • 2x Smart Cooling Fan
• 1x Power Switch
• Single ATX 150 or 250W PSU
Internal I/O • 3x SATA3
• 1x PCIe Gen3 (x8 slot, x8 Signal) (For Expansion
module)
• ATX 24-pin Power Input
• ATX 12V 8-pin Power Input
• 1x on board pin header for PIC update
• 1x on-board pin-header for I2C
• 1x on-board pin-header for PMBus
• 2*5 pin 2.54mm for 8-bit GPIO (4-In, 4-Out)
• 1x on-board pin-header for SYSTEM LEDs
Other Features
Watchdog Timer • Software programmable 0~255 Seconds, 0=disable
timer.
Battery • Lithium Battery, 3V 220mAH (CR2032), for RTC
Hardware Monitoring • CPU Voltage
• CPU Temperature
• System Temperature
Security & Mgmt. • Chassis Intrusion Detection (default: Disable)
Software
OS Support • Linux Kernel 4.8 & above, (64-bit)
Mechanical & Environment
Dimension • 440(L) x 400(W) x 44(H) mm
Operating Temperature • 0 ~ 40°C (32 ~ 104°F)
Storage Temperature • -20 ~ 80°C (-4 ~ 176°F)
Relative Humidity • 0 to 90% @40°C, non-condensing

ANR-DNV3N3-8C
7www.acrosser.com
EMC & Safety
Certication • CE, FCC Class A, RoHS 2, cULus
Vibration Test • IEC 60068-2-64, 5~500Hz, 3GRMS
Drop Test • ISTA-2A 2006
1.2. Package Contents
Check if the following items are included in the package.
Item Q’ty
�ANR-DNV3N3-8C system 1
�Console Cable (RJ-45 to Serial) 1
�Rackmount Bracket 2
�CD with Driver and Manual 1
�Power Cord 1
�Screw Pack 1

ANR-DNV3N3-8C
8Acrosser Technology Co., Ltd.
1.3. System Dissection
1.3.1. Dimensions
(Unit: mm)
440
44 400

ANR-DNV3N3-8C
9www.acrosser.com
1.3.2. Front I/O Panel
• RST
Reset Button
• Console
Console Port (RJ45)
• HDD
HDD Activity Indicator (Yellow)
• PWR
Power Indicator (Green)
• USB 3.0
USB 3.0 Port
• SFP+ 1 ~ 4
SFP+ LAN Port
• LAN 1~8
LAN 1~8 Port
1.3.3. Rear I/O Panel
AC Inlet Power Switch
• AC Inlet
1U Redundant ATX PSU
• Power Switch
Power on/off switch

ANR-DNV3N3-8C
10 Acrosser Technology Co., Ltd.
2. Components Assembly
Please follow the instruction to install the inner modules.
2.1. HDD Installation
Step 1: As shown below, insert the snap bushing into the upper ridge of the bigger
hole..
Step 2: Insert the snap bushing into the bigger hole.

ANR-DNV3N3-8C
11www.acrosser.com
Step 3: Push the snap bushing into the smaller hole.
Insert all four snap bushings.
Step 4: Insert screw into the snap bushing, and fasten to HDD.

ANR-DNV3N3-8C
12 Acrosser Technology Co., Ltd.
Step 5: Fasten the HDD with all 4 screws.
Step 6: Connect HDD with the SATA signal and power cable..

ANR-DNV3N3-8C
13www.acrosser.com
Step 7: Place the HDD bracket inside the chassis and fasten with 4 screws.

ANR-DNV3N3-8C
14 Acrosser Technology Co., Ltd.
2.2. NIM Module Insertion
The products shown in this procedule are used for illustration only, may not reect
the exact outlooks.
Step 1: Remove the screw that lock the dummy cover on Module A slot.
Step 2: Open the dummy cover.

ANR-DNV3N3-8C
15www.acrosser.com
Step 3: Insert your NIM module into the Module A slot. Firmly push it all the way
in.
Step 4: Push the latch left. This will lock the module.

ANR-DNV3N3-8C
16 Acrosser Technology Co., Ltd.
Step 5: Use your ngers to lock back the screw.
Or you may use a screw driver to lock back the screw.

ANR-DNV3N3-8C
17www.acrosser.com
2.3. Rack Installation
Step 1: Secure both left and right 1U mounting ears to the server’s front panel
chassis with your Phillips screwdriver.

ANR-DNV3N3-8C
18 Acrosser Technology Co., Ltd.
3. BIOS Settings
This chapter describes the BIOS menu displays and explains how to perform
common tasks needed to get the system up and running. It also gives detailed
explanation of the elements found in each of the BIOS menus. The following topics
are covered:
• Main Setup
• Advanced Setup
• IntelRCSetup Setup
• Security Setup
• Boot Setup
• Save & Exit Setup
Once you enter the Award BIOS™ CMOS Setup Utility, the Main Menu will appear
on the screen. Use the arrow keys to highlight the item and then use the <Pg Up>
<Pg Dn> keys to select the value you want in each item.
3.1. Main Setup
The BIOS setup main menu includes some options. Use the [Up/Down] arrow key to
highlight the option, and then press the <Enter> key to select the item and congure
the functions.
Version 2.19.1266. Copyright (C) 2020 American Megatrends, Inc.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.
Main Advanced IntelRCSetup Security Boot Save & Exit
Set the Date. Use Tab to
switch between Date
elements.
Default Ranges:
Year: 1998-2099
Months: 1-12
Days: Dependent on month
Range of Years may vary.
BIOS Information
BIOS Vendor
Core Version
Compliancy
Project Version
Build Date and Time
Memory Information
Total Memory
Ststem Date
Ststem Time
American Megatrends
5.13
UEFI 2.6; PI 1.4
01/01/2020 00:00:00
[Wed 01/01/2020]
[11:22:33]
Note: Listed at the bottom of the menu are the control keys. If you need any help with the
item elds, you can press <F1> key, and it will display the relevant information.

ANR-DNV3N3-8C
19www.acrosser.com
• Total Memory
This item displays the total size of memory available in the system.
• System Date/System Time
Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values using the keyboard. Press the
key or the arrow keys to move between elds. The date must be entered in MM/DD/
YYYY format. The time is entered in HH:MM:SS format.

ANR-DNV3N3-8C
20 Acrosser Technology Co., Ltd.
3.2. Advanced Setup
Version 2.19.1266. Copyright (C) 2020 American Megatrends, Inc.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.
IntelRCSetup Security Boot Save & ExitMain Advanced
OnBoard Bypass Controller
W83627DHG Super IO Configuration
W83627DHG HW Monitor
Serial Port Console Redirection
Trusted Computing
Network Stack Configuration
CSM Configuration
USB Configuration
OnBoard Bypass Controller
3.2.1. Advanced Setup: OnBoard Bypass Controller
Version 2.19.1266. Copyright (C) 2020 American Megatrends, Inc.
→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Aptio Setup Utility - Copyright (C) 2020 American Megatrends, Inc.
Advanced
Model Name
Firmware Version
Pair0 System On
Pair0 System Off
Pair0 WDT Timeout
Set System On Bypass
State
[Normal]
[Bypass]
[Bypass]
• Pair0 System On
Each Pair Lan[a] and Lan[b] Bypass State Setting, System On /System off /WDT
timeout State.