actionair FOAMAGIC User manual

WUA-N046-E
Thanks for choosing # Action Air
After service email: [e-mail]
USER’S MANUAL

3-WAY SWITCH
PRESSURE REGULATOR
CONNECT THE
WATER SUPPLY
1
WATER GUN
SPRAYER
2
WATER SLIDE SPRAYER
3FOAM SPRAYER LID COVER FOR WATER PLAY ONLY
YELLOW CONNECTOR
GREEN CONNECTOR
WATER TANK

1
Spreadout water slide and place on soft, level ground at least 6 feet from any structures or obstructions.
01
02
Fully stretch out air tube straight and untwisted. Pull end of the tube completely around blower spout and tighten velcro strap.
Secure blower to the ground with small blower ground stakes.
Stretch the air fill tube and position the blower (air pump) at the end of the tube.
WATER SLIDE INSTALLATION
Ⅰ

2
Attach water sprayers to corresponding numbered pads on the water slide.
Unscrew valve. (To use waterslide without foam, leave valve
closed, do not attach foam sprayer.)
Attach foam sprayer to valve, twist to lock tight.
Secure water hose from top to bottom of waterslide with
Velcro attachments. Check to be sure that any part of
hose is not twisted.
Attach the hose to water supply before turning water on.
03
Press blower switch to “On”. If blower does not turn on, press
reset button on the GFCI plug. The blower will remain on to
provide continual airflow while the waterslide is in use.
Secure water slide to the grond with ground stakes.
WATER SPRAYERS AND FOAM SPRAYER INSTALLATION
Ⅱ
1
1
11
2
2
2
2
Velcro pad

3
Water Bubble bath solution
01
Put 2.4 gallons water and 0.53 gallon bubble bath solution into a bucket. Fully stir BEFORE pouring into the water tank. Different bubble
bath solutions may have different foam effects and service time. (The recommended ratio of bubble bath solution to water is 1:4 )
Pour the mixed solution into the water tank until water (not bubbles) reaches the rim of the tank. Foam overflow is normal while filling
water into the water tank. Important: Tank must be completely full of water and air tight to create the air pressure necessary to push out
the foam.
Stir
After placing water tank near the water slide,
connect yellow connector to yellow nozzle on
water tank.
PRESSURE
REGULATOR
Connect green to green on water tank.connector nozzle
B
02
03
A
2.4
GALLON
0.53
GALLON
FOAM SYSTEM INSTALLATION
Ⅲ
Firmly push end
of regulator hose
into 3-way switch.
Foam mixture ingredient: Children bubble bath solutions.

4
04
OFF
ON
OFF
ON
01
02
OFF
ON
ON
Turn 3-way switch to “On”. Turn on water supply. Foam will take several minutes to spurt out.
Note: Volume of foam flow will gradually increase.
Unscrew the water tank cover and empty out remaining water. Refill the mixed solution
into the water tank, tighten the tank cover.
Re-insert green nozzle to green connector. Turn
3-ways switch to “On” and turn on water supply.
REFILL INSTRUCTIONS
Ⅳ
If foam runs out, follow these steps.
Pull off green connector from water tank, water may spurt from the
water tank nozzle. (Note: Gray part of connector may cause a
pinch if touched while removing.)
Turn the 3-way switch to “Off ”.

5
FOAM SYSTEM TAKE DOWN
Ⅴ
OFF
ON
01
Pull off green connector from water tank. (Note: Gray part of
connector may cause a pinch if touched while removing.)
Turn 3-way switch to “Off ”.
Turn off water supply
02
Unscrew the water tank cover. Empty water from water tank.
03
PULL
To detach end of regulator hose from 3-way switch, press in
grey connector piece and pull out hose.
Clean and dry the water tank.

ABCD
EFG
PROBLEM SOLUTION
Foam does not spurt out in 10-15 minutes.
Foam is intermittent.
Check if the foam system is installed correctly.
Check if the 3-way switch is turned to “On”.
Check if the water supply is turned on and properly connected.
CAUTION:
Foam system should not be used in high winds as this will affect the foam effect.
Foam will cause surfaces to become slippery. Use caution when walking on slippery surfaces.
Squeeze foam sprayer to loosen any blockage.
Make sure the foam tank is 100% full of water.
Make sure the foam ingredient and water have been properly stirred.
Check to see if the water hose leading from the foam tank to the foam
sprayer is twisted.
WATER SLIDE TAKE DOWN
Ⅵ
Make sure all children exit the product.
Make sure the product is free from foreign objects.
Turn off water supply. Detach water hose from the product, empty the hose and store in a cool location.
If the product comes with water bags, detach these from the product. Empty the bags and store in a cool location.
Keeping the product inflated with the blower on will help the surface of the product to dry. Later, turn over the water slide to
allow the bottom of the slide to also dry.
Press blower switch to OFF.
Unplug the blower (air pump) power cord.
Loosen the Velcro and detach the inflation tube from the blower.
The product should deflate on its own within 5 minutes. Make sure the product is entirely deflated.(refer to picture A)
Remove ground support stakes.
Fold the product in half from both ends, and then fold it in half 2 more times from both sides, vertically to the first fold. (refer to
picture B,C,D)
Roll it up tightly from the end opposite the inflation tube.(refer to picture E,F)
Slide the carry bag over the folded product and zip up the bag.(refer to picture G)
Product must be 100% dry before storing. Store the product and blower inside when not in use.
Swiftech Company Ltd.
Dongcheng Industrial Zone, Xinping Road, Minzhong Town, Zhongshan City, Guangdong Province, China
®
and Foamagic are trademarks of Swiftech Company Ltd. © 2021 Swiftech Company Ltd. All rights reserved. Action air ®