AEG NOVAMAT 430 User manual

Instructions for use GB
Washing machine
NOVAMAT 430
129 0690 40

NOVAMAT 430
Before first use, remove the internal packing of your
washing machine !
Technical data
• Dry clothes loading capacity : cotton 5 kg
synthetics 2,5 kg
wool 1 kg
• Dimensions : height without backpanel : 850 mm
height with backpanel : 895 mm
width : 450 mm
depth : 600 mm
• Voltage : 230 V
• Heater rating : 1950 W
• Power absorbed : 2200 W
• Spinning speed : 800 rpm
Your washin machine
Programmes
• • • •
• • • •
• • •
• • •
• •
• •
• •
•
• • •
• •
• •
• •
•
•
1
1
2
2
3
4
5
6
7
8
9
10
11
12
13
14
Whites, very soiled with prewash
Economy with prewash + E button
Whites, soiled, without prewash
Economy without prewash + E button
Resistant coloureds
Delicate coloureds
Rinses
Softening
Spinning
Resistant, very soiled with prewash
Resistant,normallysoiled
Delicates, normally soiled
Very delicate textiles - Wool
3 Rinses
1 Rinse with Softener
Draining
5 kg
2,5 kg
1 kg
2,5 kg
5 kg
Temp.
°C Max.
load End of prog.
Products
Prog.
90
60
90
60
60
40
60
60
40
30
Cotton - linen
Synthetics
Draining
Rinse hold Spinning
Before each wash, make sure that :
• the drain hose is correctly placed
• the water tap is turned on (fully open)
• the plug is in the wall socket
• the timer knob is on the "off" position (pressed out, position "0")
Your washing machine is ready to
operate :
• lift up the lid of the machine
• open the drum with your two hands by pres-
sing the button Aand the two flapdoors till they
disengage
• introduce the laundry into the drum ; close the
drum and the lid of the machine
Be careful : before closing the lid of your ma-
chine, make sure that the drum flapdoors are
correctly closed :
- the two flapdoors fastened
- the button Apressed out
The detergent dispensers :
aprewash compartment ( a )
bmain wash compartment ( b )
cbleach compartment (c )
dsoftener compartment (d )
If you wish to use liquid detergent :
• choose a programme without prewash
• pour the recommended quantity of liquid
detergent into the main wash compartment (b
a b c d
Whentheselectedprogrammeisover,themachinestopsautomatically.The timer knob
stops on the position "I".
The "synthetics" programmes end with a rinse hold to avoid the creasing of the laundry
in case it is not taken away from the drum just after the wash.
To end these programmes, you can select a spinning (programme 7) or a draining
(programme 14).
To end the wool programme, we advise you to realize a draining programme.
Be careful : the lid can only be opened 1 or 2 minutes after the machine has stopped.
After each wash :
• press the timer knob ; the control lamp lights off.
• press out the pushbuttons if necessary.
• unplug the machine from the wall socket and turn off the water tap.

Control panel
AEG NOVAMAT 430
123
4
I 0
•choose the programmeaccording
to the nature and the degree of soil
of the laundry.
• simultaneously push and turn the
timer knob clockwise to select the
chosen programme.
1Select the programme
•choose thetemperaturewhich cor-
responds to the chosen programme
(see indications on the programme
table).
2Select the temperature
123
4
I 0
34Pull the timer knob
Press the pushbuttons
if necessary
• The programme starts. The control
lamplights on.
123
4
I 0
•Half-loadpushbutton" " : if pressed
at the beginning of an energic wash
programme, it enables to wash
economically small quantities of
laundry,upto2,5kgofresistantlaundry
(cotton-linen).Thisbuttoncanonlybe
usedwith the programmesforcotton
andlinen.
• Energy saving pushbutton " " :
this pushbutton enables to save a lot
of energy by limiting the water
temperature at 60°C (temperature
knobon "E").Theother characteristics
of the programme remain
unchanged.
• Spinning suppression pushbutton
"":itenablestosuppressthespinning
phases of the programme for
resistantlaundry (cotton-linen) when
you wish to wash delicately your
laundry. The programme ends then
withadraining.

The products (see the leaflet "Washing guide")
Follow the manufacturer's instructions for recommended quantities.
If the water is soft, decrease the quantity.
Ifthe water ishardor if thelaundryis very soiledorstained, increasethedetergentquantity
a little. For information regarding the degree of hardness in your area, enquire with your
localauthorities.
Bleach
You may use a bleach agent in all the washing programmes. However, make sure that
thefabric withstands the treatment.Bleachis automatically washed downintothe drum.
Pour1/4to1glassof12°chlbleachintocompartment"c "beforeswitchingthemachine
on. Make sure that the level of the liquid never exceeds the "MAX" mark.
Softener
Compartment "d" allows automatic addition to the last rinse of a liquid softener.
Follow the quantities recommended on the bottle. Make sure that the level of the liquid
never exceeds the "MAX" mark.
Removal of internal packing
The parts protecting the inner components of the machine during transit are red. They
must all be removed before using your machine for the first time. These parts and their
securing means should be kept in case the machine has to be transported again.
1. Tilt the machine backwards (fig. 1).
2. Unscrew and remove the 2 screws Aend the 2 red washers Bsituated under the
washing machine, then pull on the red plastic ring to take part Cout of the machine
(fig.1).
3. Straighten up the machine.
4. After removing the 4 nuts D, the 4 washers (fig. 2), remove the 4 red plastic sleeves
E: pull the ring, rotating it at the same time leftwards and rightwards (fig. 3).
Ifyou do not manage to taketheredsocket off, use a wrenchandturnit anticlockwise
as shown on the picture (fig. 3 et 4).
5. Unscrew and remove the 4 threaded pins F.
6. Plug the holes left by pins Fwith plugs G(to be found in the plastic bag with the
instructionmanual) taking caretoshutdown the centralpartas shown ondrawing(fig.
5) and take the polystyrene block (fig. 6) away.
Your washing machine is now ready to be operated.
Electrical connection
Before you plug the appliance into the wall socket, make sure that :
• The supply voltage of the domestic wiring system
does not fluctuate by more than 10% plus or minus
from the value shown on the rating plate.
• The meter, the fuses, the supply line and the wall
socket are all suitable to carry the maximum load
required by the washing machine (2,2 kW).
The existing safety rules call for the appliance to be
connected to an efficient ground wire.
The manufacturer disclaims any liability whatsoever
if this accident prevention rule is not complied with.
This appliance complies with E.E.C. directive n° 87/
308 of 06.1987 relative to radio interference suppression.
Water connection
• The end of the water inlet hose must be connected to a cold water tap having 3/4" gas
thread spout or to a water tap having a quick-coupling connector after having introduced
in the hose ring nut a rubber sealing washer also provided with the machine.
• The curved end of the outlet hose should be inserted into a drain pipe not less than 70 cm
and not more than 1,0 m from floor level.
Make sure that the drain hose is always safely secured so that it will not become loose or fall
down from its position.
The water should drain freely and consequently, the drain hose should not be chocked or
placed in such a way as to obstruct the normal water flow.
If an extension is required, remember that it might cause a malfunction in the drain pump,
particularly if the extension has a length in excess of 1 meter or if the diameter of the extension
is smaller than the diameter of the original drain hose.
Water pressure : minimum 5 N/cm2(0,5 kg/cm2)
maximum 80 N/cm2(8 kg/cm2)
Levelling and positioning
Cleaning the drain filter
Subject to technical alterations.
The machine is equipped with a drain filter
located at the front bottom behind a small
flapdoor.
Thisfilter should becleaned regularlyas follows:
• open the flapdoor of the filter compartment
by pressing it inwards with a finger at the
higed side
• turn the filter knob anticlockwise and pull
the filter out
• clean the filter thoroughly
• refit the filter and turn the knob clockwise.
Level the appliance very
carefullybyadjusting the le-
velling feet located at the
front of the base.
Then tighten the lock nuts at
the top of the feet, using a
spanner.
To enable the ap-
plianceto be moved
with ease, it is provi-
ded with two fixed
wheelslocatedat the
rear of the base.
Be careful : when the machine is installed on carpeted floor, ensure that the carpet
donot obstructtheopenings, located atthebase ofthemachine, whichareprovided
for ventilation.