aguri Fusion GTX200 User manual

www.aguriworld.co.uk
User Manual
Benutzerhandbuch
Manuale utente
FUSION
GTX200

EN • 2
EN • 3
Fusion GTX200 User Manual
Contents
Fusion speed trap detection settings
Product overview 3
What’s in the box 5
Speed trap detection
standby screen explained 5
Installation 6
Fusion default speed
detector settings 7
Using Fusion around Europe 8
GPS speed trap settings 10
Quick start setting 10
Software version 10
Change screen colour 10
Voice alerts 11
Auto Mute 11
City button & Smart Filter settings 11
Brightness control 12
On/Off/Volume control 12
Speed unit - KMH/MPH 12
Speed limit 12
GPS Clock 13
Changing the language 13
Factory reset 13
Updating the speed trap database
and system software using a PC 13
Updating your Fusion speed trap
database and system software
using a Mac 14
Fusion DVR Dash cam settings
Resolution 21
Video quality 21
Set Video loop time 21
Microphone 22
Time lapse 22
Language 22
Car number set 23
Format the SD Card 23
Date/time stamp 23
Auto LCD off 24
Parking Mode 24
Default setting 25
Video playback 25
Video playback using
Aguri Fusion PC video software 25
Flicker – adjust Hz rate 28
G-sensor shock/impact sensor 28
GMT - GPS auto update time 28
WDR – Wide Dynamic Range 29
Technical specication -
DVR dash cam 29
Disposal of Old Electrical
& Electronic Equipment 30
Warranty 31
Copyright
Copyright @2016 Aguri Limited. All rights reserved.
Product specications and features are for reference only and are subject to change without prior
notice.
Declaration
This User Manual is published by Aguri Limited without any warranty. Improvement and changes
to this User Manual necessitated by typographical errors, inaccuracies of current information, or
improvements to programs and/or equipment, may be made by Aguri Limited any time and without
notice. Such changes will, however, be incorporated into new editions of this User Manual.

EN • 2
EN • 3
1. Windscreen bracket
2. Menu button
3. Dim button
4. Mute button
5. City button – use to switch Smart
Filter modes to reduce false alerts.
6. Micro SD card slot for use with
DVR Dash cam.
7. Speed trap detection OLED
8. DVR dash cam 1.5” colour LCD
9. Rec button. Press to manually start
and stop recording. Press and hold
to enter DVR dash cam settings
menu.
10. Down arrow button. Press to turn
DVR microphone on and off. Use to
scroll down through menu options.
11. Up arrow button. Press to manually
turn off DVR LCD. Use to scroll up
through DVR menu options.
12. Mode button. Press and hold to
play video back on the device.
13. Alternative 12V Mini USB power
connection point.
Product overview
1
2
6
7
910 11
3
4
5
8
12
10
11

EN • 4
EN • 5
1. Built-in speaker
2. Windscreen bracket mounting slot.
3. Built-in Laser detector
4. Radar detector
5. DVR dash cam 170 degree wide-
angle lens video recorder
6. Combination Volume/on/off button
7. Micro USB data transfer socket.
To be used for updating the DVR
dash cam only. Do not use to
power the device.
8. Mini HDMI socket. Connect to a
TV to play back video directly from
the device.
9. 12V Mini USB power connection
point. Connect the 12V vehicle
charger supplied here or connect
mini USB data cable to update
speed trap database and software.
10. Built-in Ambarella A7L HD video
processor.
1 2
67
9
10 3
4
5
8

EN • 4
EN • 5
Whats in the box?
1 x Aguri Fusion GTX200
1 x USB data cable
1 x 12V car power connector
1 x 12V ‘hardwire’ power connector
1 x GPS windscreen bracket
1 x User guide
Speed trap detector standby screen
explained
Smart Filter
status
GPS status.
(a cross will appear over
the GPS icon if there is
no signal)
Mute speaker
status
on or off
GPS compass Your speed
GPS Clock
GPS Date
Your speed
indicator graphic

EN • 6
EN • 7
Installation
Attach the windscreen bracket by sliding it in to the slot on the top of the
unit. Find a suitable area off the windscreen to mount the unit where it
has an unobstructed view of the road ahead and a clear view of the sky
so that the GPS windscreen bracket can connect to satellites. If you are
powering from the cigarette lighter socket we recommend mounting it
toward the bottom of the windscreen, just above the dashboard so that it
has a good view of the road ahead, but so that it’s view is not obstructed
by the windscreen wipers. Alternatively, you can mount it at the top
of the windscreen near to the rear view mirror, but this might only be
convenient if you intend to ‘hard wire’ the unit directly to your vehicle’s
electrical system.
User tip. Remember that you will need to attach the power cable,
so nd a position where this can be done without obstructing
the vehicle’s controls or becoming a danger to the driver or
passengers.
Once you have chosen a suitable location, press the suction cup bracket
quite rmly to the glass with the lever in the ‘unlock’ position and then
rotate the lever 90 degrees in to the ‘lock’ position to secure. Finally,
loosen the nut slightly and adjust the bracket so that the unit is in a
horizontal position and then re-tighten.
Connecting to power
Attach the mini USB plug on one end of the power cable to either the
mini USB socket on the side of the unit or the mini USB socket on the
lever of the GPS windscreen bracket depending on which is the most
convenient for your installation. Insert the other end in to an appropriate
cigarette lighter/12V socket in your vehicle.
Please note that you should only use the 12V cigarette lighter
adaptor or the 12V hardwire lead supplied to power the unit. Most
other USB supplies, such as the accessory style USB socket,
sometimes tted to newer vehicles, will only provide a 5V output
which will be insufcient to power the unit.
Your speed indicator
graphic

EN • 6
EN • 7
Installation tips
Before mounting your Fusion, clean the area of the windscreen where
you have chosen to mount your unit, with a good quality glass cleaner to
ensure the suction cup bracket makes a good contact.
Remember to mount the unit and install the power cable safely in a
location where it does not interfere with the driver or the controls of the
vehicle.
It is also possible to ‘hard-wire’ your Fusion and hide the power cables,
providing a neater installation. Please contact an auto electrician or your
local car dealer for further details.
General operation
Aguri Fusion combines a GPS, radar, and laser speed trap detector
and a high performance DVR dash cam in one unit. Below you will nd
separate set-up instructions for each.
Fusion speed detector settings
We have shipped your Fusion with the user settings, set for optimum
performance in the UK as follows:-
Radar/laser alert settings
X Band - Off
K Band On
Ka Band - Off
Laser - On
GPS alert settings
Speed trap alerts – On
Red light cameras – On
Mobile speed trap locations – On
Smart Filter – 1
AutoMute – On
It is however, possible to change these settings to suit your own
requirements. For further information follow the instructions below.

EN • 8
EN • 9
Menu settings
Radar/Laser settings
It is possible to switch individual radar frequencies on and off, to ne tune
Fusion to the country you are driving in.
Enter the menu by pressing the ‘menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see the radar frequency you
want to change. Press the ‘City’ button to switch the frequency on or off
and press the ‘Menu’ button to conrm and return to the menu.
The following options are available:-
X Band – On/Off
K Band – On/Off
Ka Band – On/Off
Laser – On/Off
User tip: We recommend you keep Laser switched on at all times.
Using Fusion around Europe
Below are the radar/laser set-ups we would recommend for a selection
of other countries if you using your Fusion outside of the UK.
Germany/Austria
Radar/laser alert settings
X Band - Off
K Band On
Ka Band - On
Laser - On
GPS alert settings
Speed trap alerts – On
Red light cameras – On
Mobile speed trap locations – On
Spain/Portugal
Radar/laser alert settings
X Band - On

EN • 8
EN • 9
K Band On
Ka Band - On
Laser - On
GPS alert settings
Speed trap alerts – On
Red light cameras – On
Mobile speed trap locations – On
Italy
Radar/laser alert settings
X Band - Off
K Band On
Ka Band - On
Laser - On
GPS alert settings
Speed trap alerts – On
Red light cameras – On
Mobile speed trap locations – On
Warning. Please note that it is illegal to use a GPS/radar/laser
detector in France and the Republic of Ireland.
Please note that it may be illegal to use a radar/laser detector in
Spain and Germany, so please check local laws before using Fusion
in Spain and Germany.
Warning. Whilst we have provided some advice on the use of GPS/
radar/laser detectors above, the laws surrounding the use and
ownership of GPS speed trap detectors and radar/laser speed trap
detectors, varies from country to country. It is the sole responsibility
of the driver to check the local laws of the country they are driving
in or intend to drive in, before using Fusion or any other form of
GPS speed trap detector or radar/laser speed trap detector.

EN • 10
EN • 11
GPS speed trap settings
The GPS speed trap settings, control alerts to the locations stored in the
Speedshield database that is pre-loaded in to your Fusion.
It is possible to individually switch alerts to these locations, on or off, to
suit your personal requirements. The following options are available:-
GPS Speed traps – On/Off
Red Light cameras – On/Off
High Risk Zone locations – On/Off
SPECs average speed cameras – On/Off
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see the speed trap/red light
camera/high risk zone location/SPECs average speed camera setting
you want to change. Press the ‘City’ button to switch the setting on or
off and press the Menu button to conrm and return to the menu.
Quick start
When you power the device on, the unit will go through a start-up
sequence conrming the current status of the unit. The sequence will tell
you which features are on and off. If you do not wish to see this, you can
switch the ‘Quick start’ feature on.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Quick start’. Press the
‘City’ button to select or de-select it and press the ‘Menu’ button to
conrm.
Software version
Select ‘I Vers.’ to conrm what version of the operating software is
currently installed on your device.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Version’ and press the
‘City’ button. Press the ‘Menu’ button to return to the menu.
Change screen colour
It is possible to choose between three different screen colours, orange,
blue, and ‘All colour’.

EN • 10
EN • 11
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Orange colour’, ‘Blue
colour’ or ‘All colour’. Press the ‘City’ button to switch between the
colours and then press the ‘Menu’ button to conrm and return to the
menu.
Voice alerts
It is possible to switch the voice alerts on or off.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Voice’. Press the ‘City’
button to switch the voice on and off and then press the ‘Menu’ button
to conrm and return to the menu.
Auto Mute
Fusion comes with Auto Mute switched on as standard. When switched
on, the unit will emit an audible alert at your preferred volume each
time it alerts to a speed trap, but after a few seconds will automatically
reduce the volume to a lower level.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Auto Mute’. Press the
‘City’ button to switch Auto Mute on or off and press the ‘Menu’ button
to conrm and return to the menu.
City button and Smart Filter settings
There are three Smart Filter settings that can be used to reduce the
amount of ‘False’ radar alerts you may get from other ‘non-police’ radar
sources, such as automatic doors at petrol stations and supermarkets.
Smart Filter 1 – Low ltration
Smart Filter 2 – Medium ltration
Smart Filter 3 – High ltration
The current Smart Filter setting is identied on the OLED display. Press the
‘City’ button once to change the setting.

EN • 12
EN • 13
Brightness control
The brightness control button controls the brightness of the speed trap
detection display. You can choose between three levels of brightness.
Bright
Dim
Stealth
Press the ‘Dim’ button once to switch between the different brightness
settings.
On/Off/Volume control
Press and hold the volume control in towards the unit once, to power
your Fusion on and off.
Decrease the volume by pulling and holding the volume control button
towards you.
Increase the volume by pushing and holding the volume control button
away from you.
Speed unit - KMH/MPH
Use this feature to switch between MPH and KMH.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see MPH or KMH. Press the
‘City’ button to choose MPH or KMH and press the ‘Menu’ button to
select and return to the menu.
Speed limit
Use this feature to set the unit to alert you if you exceed a pre-selected
speed limit.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Speed Limit’ and press
the ‘City’ button to select. Use the ‘Dim’ (+) or ‘Mute’ (-) buttons to select
the speed limit you would like to be alerted to and press the ‘Menu’
button to conrm your selection and return to the Menu.
User tip: If you do not want to be alerted to a speed limit, set the
speed limit to ‘Disable’.

EN • 12
EN • 13
GPS Clock
Fusion will automatically display the time using GPS based on the GMT
time zone. Use this setting to adjust the time to DST or a different time
zone, depending on your location.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘GMT’ and press the
‘City’ button to select. Use the ‘Dim’ (+) or ‘Mute’ (-) buttons to add or
deduct hours from GMT as necessary and press the ‘Menu’ button to
save your selection and return to the menu.
Changing the language
Follow these instructions to change the language.
Press the ‘Menu’ button on the top of the unit and use the left or
right arrow buttons to scroll through the menu until you see ‘Change
language’ and press the ‘City’ button. Use the right or left arrow buttons
to scroll through the different language options and press the ‘City’
button to select your preferred language. Press the ‘Menu’ button to
return to the menu and then press the menu button again to return your
Fusion to the normal operation mode.
Factory reset
Use this feature to return the speed trap detector features of your Fusion
to the original factory default settings.
Enter the menu by pressing the ‘Menu’ button. Scroll left or right, using
the ‘Dim’ (+) or ‘Mute’ (-) buttons, until you see ‘Factory Reset’ and press
the ‘City’ button to select it. Use the ‘Dim’ (+) or ‘Mute’ (-) buttons to
choose either ‘OK’ or ‘Cancel’ and press the ‘Menu’ button to select and
return to the menu.
Updating the speed trap database and
system software using a PC
Please note that your Fusion has been delivered with the latest
software and speed trap database already pre-installed, so it will
not be necessary to perform an update immediately.
When an update is required, the speed trap database and software
updater can be found on the CD Rom supplied in the box or can be

EN • 14
EN • 15
downloaded from the Software Updates section that can be found at the
bottom of any page on our website
www.aguriworld.co.uk
If you are using the CD Rom, insert it in to your PC and open it so that
you can view the les saved on to it. You will see a copy of the User
manual and a piece of software entitled ‘Aguri Skyway Fusion DB
Updater V(?)’ Left click on the updater and ‘drag’ it from the CD Rom,
on to the Desktop of your computer. Double click on the Aguri Skyway
Fusion DB Updater icon that is now on your desktop and the updater
software will open in a new window.
Next press and hold the Power/Menu button on your Fusion and connect
it to your PC using the Mini USB data cable provided. Once connected,
release the Power/Menu button and wait a couple of seconds until your
Fusion establishes a connection with your PC. If any additional windows
appear, please close them. If your Firewall software asks you if you want
to let the Fusion or the Fusion updater software operate on your PC
please let it do so.
Once Fusion has established a connection, please press the ‘Connect’
button on the Aguri Skyway Fusion DB Updater window. The window will
now display a message ‘Connect to server, please wait’.
User note: The Aguri Skyway Fusion Updater software will only work
if your PC is connected to the internet.
When the server connection has been established the ‘Download’ button
on the Aguri Skyway Fusion DB Updater window will be highlighted.
Press ‘Download’ to start the update. The progress bar will keep you
informed of the status of the update.
The Aguri Skyway Fusion DB Updater window will inform you once the
update is complete and it is safe to unplug your unit.
Updating the speed trap database and
system software using a Mac
Aguri Skyway speed trap database Mac updater is compatible with Mac
OS El Capitan 10.11 and Yosemite 10.10

EN • 14
EN • 15
1. Double click on the Aguri Skyway Fusion installer to begin
installation
2.

EN • 16
EN • 17
3.
4.

EN • 16
EN • 17
5.
6.

EN • 18
EN • 19
7.
8.
Select “Restart” to reboot your Mac and complete the installation.
9. When your Mac restarts the Aguri Skyway Fusion updater program
will be found in the Application folder.

EN • 18
EN • 19
10. Next press and hold the Power/Menu button as you connect your
Fusion to your Mac using the Mini USB data cable provided. Once
connected, release the Power/Menu button and wait a couple of
seconds until the Fusion has established a connection with you Mac.
11. If any additional windows appear, please close them. If your Firewall
software asks you if you want to let the Fusion or the Fusion Updater
software operate on your Mac please let it do so.
12. Once your Fusion has established a connection, please press the
‘Connect’ button on the Skyway Fusion DB Updater window. The
window will now display a message ‘Connect to server, please wait’.
User note: The Aguri Skyway Fusion DB Updater software will
only work if your Mac is connected to the internet.
13. When the server connection has been established the ‘Download’
button on the Aguri Fusion Skyway Updater window will be
highlighted. Press ‘Download’ to start the update. The progress bar
will keep you informed of the status of the update.
14. The Aguri Skyway Fusion DB Updater window will inform you once
the update is complete and it is safe to unplug your Fusion. Your
Fusion will now be up-to-date and ready to use.
If you need any further assistance with the installation of this software or
require more advice on how to use the software please call Aguri Customer
Service 0330 102 5578.

EN • 20
EN • 21
Updating the speed trap database using the wireless
Bluetooth function and an Android Smart Phone
or iPhone
It is possible to pair your Fusion GTX200 with a Smart Phone or iPhone
using Bluetooth and update the speed trap database wirelessly rather
than using a PC or Mac.
1. Download the Aguri Updater app from the App Store or Google Play
store and install it on your iPhone or Android Smart Phone. Go to the
Settings menu on your phone and ensure that Bluetooth is switched on
and then open the Aguri Updater app so it is ready to use.
2. Power on your Fusion GTX200 using the 12V cigarette lighter cable or
hard-wire cable supplied. Please note that this wireless updater function
is designed to enable you to update the unit in your vehicle.
3. Press the ‘Menu’ button on top of the unit and then scroll through the
menu using the left or right arrow buttons until you see ‘Bluetooth Mode’
and press the ‘City’ button to select it.
4. Next press the ‘Connect’ button on the Aguri Updater app on your
phone and a window should pop up displaying the message ‘Select
your device’. Press ‘Scan’ to search for your Fusion and then tap on it to
select it once your Fusion has appeared on the screen.
5. The app on your phone will then display a list of countries to
download. Select the name of the country or countries you would like to
update and press the ‘OK’ button. Please note that the more countries
you select, the longer it will take to update the database.
6. Once you have conrmed the country or countries you want to
download, press the ‘Download’ button to proceed. Your Fusion and the
Aguri Updater app installed on your phone will keep you informed of it’s
progress.
7. Once the download is complete, your Fusion will return to the normal
operation mode and the Aguri Updater app will display the message
‘Download successful’. Press the ‘Exit’ button on the app to complete
the download and close it. Your Fusion is now up-to-date and ready to
use.