AJA RovoRx-HDMI Operating instructions

RovoRx
UltraHD HDBaseT Receiver
Version 1.0r1
Published June 9, 2017
Installation and Operation Guide

RovoRx UltraHD HDBaseT Receiver v1.0r1 2 www.aja.com
Notices
Trademarks
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.
for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for
use with recorder, router, software and camera products. Because it matters.™ is a
trademark of AJA Video Systems, Inc. for use with camera products.
CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered
trademarks of AJA Video Systems, Inc.
AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,
V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.
AirPort, Apple, Apple logo, AppleShare, AppleTalk, FireWire, iPod, iPod touch,
Mac, Macintosh and ProRes, are registered trademarks of Apple Inc. Final Cut Pro,
QuickTime and QuickTime logo are trademarks of Apple Inc.
Avid, Avid DNxHD and Media Composer are registered trademarks of Avid
Technology, Inc.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States
and/or other countries.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing, LLC.
DVI is a registered trademark of DDWG.
TASCAM is a registered trademark of TEAC Corporation.
Dolby and the double-D Dolby logo are registered trademarks of Dolby Laboratories
Licensing Corporation.
openGear® Ross, ROSS, ROSS®, and MLE are registered trademarks of Ross Video.
DashBoard Control System™ is a trademark of Ross Video.
All other trademarks are the property of their respective holders.
Copyright
Copyright © 2017 AJA Video Systems, Inc. All rights reserved. All information in
this manual is subject to change without notice. No part of the document may be
reproduced or transmitted in any form, or by any means, electronic or mechanical,
including photocopying or recording, without the express written permission of AJA
Video Systems, Inc.
Contacting AJA Support
When calling for support, have all information at hand prior to calling. To contact AJA
for sales or support, use any of the following methods:
Telephone [phone]
FAX [phone]
Web https://www.aja.com
Support Email suppor[email protected]
Sales Email [email protected]

RovoRx UltraHD HDBaseT Receiver v1.0r1 3 www.aja.com
Contents
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 1 – RovoRx Introduction . . . . . . . . . . . . . . . . . . . . . .4
System Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Pairing RovoRx with HB-T Transmitters . . . . . . . . . . . . . . . . . . . . . . . . 6
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
What’s In The Box?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
In This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Chapter 2 – RovoRx-HDMI Receiver . . . . . . . . . . . . . . . . . . . .9
RovoRx-HDMI Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RovoRx-HDMI Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RovoRx-HDMI Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
RovoRx-HDMI I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RovoRx-HDMI Installation with RovoCam . . . . . . . . . . . . . . . . . . . . . 10
RovoRx-HDMI Rack Mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Chapter 3 – RovoRx-SDI and Mini-Cong . . . . . . . . . . . . . . . . 12
RovoRx-SDI Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
RovoRx-SDI Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
RovoRx-SDI Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RovoRx-SDI I/O Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
RovoRx-SDI Installation with RovoCam . . . . . . . . . . . . . . . . . . . . . . . 14
RovoRx-SDI Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
USB Control and Setup—Using AJA Mini-Cong . . . . . . . . . . . . . . . . . . 15
Acquiring AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installing AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Running AJA Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operating AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Input Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Output Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Audio Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Update Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Software Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 27
RovoRx-HDMI Tech Spec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
RovoRx-SDI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . .31
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

RovoRx UltraHD HDBaseT Receiver v1.0r1 4 www.aja.com
Chapter 1 – RovoRx Introduction
System Overview
RovoCam is AJA’s first compact block camera for industrial, corporate, security,
ProAV and broadcast applications.
RovoRx-HDMI and RovoRx-SDI are companion receiver units that offer the
simplest reception option for RovoCam. They are UltraHD/HD HDBaseT Receivers
with integrated HDMI or SDI video and audio outputs specifically designed to
receive RovoCam’s output and drive displays. This allows one to receive the
RovoCam’s output up to 100m (328’) away from the camera itself and display the
output on a display wherever needed, greatly simplifying workflows and systems
integration.
A single Cat5e/6 cable carries all uncompressed video, two-channel audio, VISCA
camera control, and power for the simplest installation ever due to RovoCam’s
integrated HDBaseT interface. Delivering this much functionality and power with
single cable connectivity dramatically simplifies the installation, camera setup
and footprint requirements.
RovoRx-SDI includes a frame sync function which supports using a RovoCam
camera feed in a video production environment.
RovoRx-HDMI and RovoRx-SDI can also be used with any compatible HDBaseT
transmitter, not just RovoCam.
NOTE: The HDBaseT format uses RJ-45 connectors but does not support Ethernet.
HDBaseT is point-to-point signal transport.

RovoRx UltraHD HDBaseT Receiver v1.0r1 5 www.aja.com
Figure 1. RovoCam System Diagram, with Audio and Computer
Computer with
VISCA Control App
HDMI
HDBaseT
(Video, Audio, Power,
RS-232 Control)
RovoCam
Stereo Microphone
(3V PiP)
Audio Out
(Left Right Analog)
RovoRx-HDMI
UHD or HD
HDMI Monitor
RS-232
RovoCam can receive power from the RovoRx over a Cat5e/6 cable (Figure 1), or
powered locally using its 12VDC connector (Figure 2).
Figure 2. RovoCam System Diagram, with Hardware Controller
VISCA Hardware
Controller
HDMI
HDBaseT
(Video, RS-232 Control)
Local
Power
RovoCam
RovoRx-HDMI
UHD or HD
HDMI Monitor
RS-232

RovoRx UltraHD HDBaseT Receiver v1.0r1 6 www.aja.com
Figure 3. Two RovoCam System Diagram, with RovoRx-SDIs
Computer with
RovoControl
RovoRx-SDI
RovoRx-SDI
HDMI
UltraHD
SDI Out
UltraHD
SDI Out
RS-232
RS-232
RovoCam
UHD or HD
HDMI Monitor
HDMI
HDBaseT
HDBaseT
RovoCam
UHD or HD
HDMI Monitor
Ref In
Ref In Video Switcher
RS-232 Port 2
RS-232 Port 1
Big Screen
Stadium Display
Pairing RovoRx with HB-T Transmitters
RovoRx-HDMI and RovoRx-SDI can also receive HDBaseT signals up to UltraHD
from other HDBaseT transmitters. Examples include AJA’s HB-T-HDMI and HB-T-
SDI model Mini-Converters.
An AJA RovoRx device may work with other HDbaseT sources, although it was
primarily designed to receive signals from RovoCam. This manual focuses only on
using RovoRx with RovoCam.

RovoRx UltraHD HDBaseT Receiver v1.0r1 7 www.aja.com
Features
Hardware
RovoRx-HDMI
• 1 x HDMI 1.4b output
• 2 x RCA analog audio outputs
• 1 x RS-232 for RovoCam control via SONY VISCA
• 1 x HDBaseT connector (RJ-45)
• 1 x USB HDBT (future use)
• 48VDC power supply (included)
RovoRx-SDI
• 1 x HDMI 1.4b output
• 4 x 6G/3G-SDI BNC outputs
• Loop through Reference BNC
• 2 x RCA analog audio outputs
• 1 x USB for rmware upgrades and Mini-Cong conguration
• 1 x RS-232 for RovoCam control via SONY VISCA
• 1 x HDBaseT connector (RJ45)
• 1 x USB HDBT (future use)
• 48VDC power supply (included)
Software
• AJA RovoControl software available for download from the AJA website
• RovoCam accepts VISCA camera control
• A variety of third-party software controllers are also available.
• RovoRx-SDI can use AJA’s Mini-Cong application for rmware updates and
advanced conguration.
Warranty
• Five year AJA warranty on RovoRX-HDMI and RovoRx-SDI.
What’s In The Box?
When you unpack your product you’ll find the following components:
• AJA RovoRx-HDMI or RovoRx-SDI Mini-Converter
• 48VDC power supply with AC cable
• (RovoRx-SDI only) standard USB to USB micro cable
In addition the following item is available from AJA as part of the HB-CABLE-KIT:
• 3.5mm TRS to DB9 adapter cable
NOTE: This cable is also widely available for purchase from other sources.
Please save all packaging for future shipping.

RovoRx UltraHD HDBaseT Receiver v1.0r1 8 www.aja.com
In This Manual
Chapter 1 - Introduces the RovoCam system, briefly describing the components,
features, box contents, and system requirements.
Chapter 2 - Describes the RovoRx-HDMI hardware, connections, and system
installation.
Chapter 3 - Describes the RovoRx-SDI I hardware, connections, system installation,
and configuration using Mini-Config.
Appendix A - Provides specifications for various aspects of the system.
Appendix B - Contains important caution, warning, and compliance statements.
Warranty and Index

RovoRx UltraHD HDBaseT Receiver v1.0r1 9 www.aja.com
Chapter 2 – RovoRx-HDMI Receiver
RovoRx-HDMI Overview
RovoRX-HDMI converts uncompressed HDMI Video/Audio signals up to UltraHD
for reception via HDBaseT over CAT type twisted pair cable. It can also send
and receive RS-232 control signals over the same cable. Video and audio can be
received by this device over distances up to 328 feet/ 100 meters on Cat 6a cable.
See "Appendix A Specifications" on page 27 for a complete list of supported
formats, frame rates, and CAT cable requirements.
The simple and economical RovoRx-HDMI is designed to pair with the AJA
RovoCam camera, to provide video, audio, control and power transmission using
a single CAT cable. RovoRx-HDMI can also be used with any compatible HDBaseT
transmitter, including AJA’s HB-T-HDMI and HB-T-SDI Mini-Converters.
RovoRx-HDMI Features
RovoRx-HDMI
• 1x HDMI (UltraHD capable) output
• Extend uncompressed UltraHD or HD HDMI signal up to 100m over CAT cable
• RS-232 control on the same RJ-45 cable
• Two channel unbalanced analog audio outputs, when used with RovoCam
and optional stereo microphone
• 48VDC power supply (included)
• Optional RS232 Cable Kit (HB-CABLE-KIT)
• 5-year warranty
RovoRx-HDMI Block Diagram
USB Port
RJ-45
HDBaseT In
RS-232 Out
Power Out
+48 VDC
HDMI Output
RS-232 In
Left Audio Out
Unbalanced RCA
Right Audio Out
Unbalanced RCA
RS-232
Receiver
Power
Distribution
HDBaseT
Receiver +10dB
(Future Use)

RovoRx UltraHD HDBaseT Receiver v1.0r1 10 www.aja.com
RovoRx-HDMI I/O Connections
LINK LED
HDMI Output
Connector
3.5mm TRS
RS-232 Port
HDBaseT
Input
Connector
DC Power
Input
Right Analog
Audio RCA Output
Left Analog Audio
RCA Output
LOCK LED
Power LED
(Future Use)
NOTE: The LINK LED, when green, indicates an active HDBaseT connection.
NOTE: The LOCK LED, when blinking green, indicates a lock to a valid video source.
System Installation
RovoRx-HDMI Installation with RovoCam
Typically, installation consists of the following steps:
1. Ensure the RovoRx-HDMI converter is disconnected from power.
2. Connect the RovoCam HDBaseT RJ-45 output to the HDBaseT RJ-45 input
connector with an approved CAT cable type and length.
3. Connect the RovoRx-HDMI output to the HDMI input of a destination device
(in this example, an HDMI monitor) with an HDMI cable.
4. Connect the 48 VDC power connector to the RovoRx-HDMI, and then
connect the provided DC power supply to an AC power source with the
supplied cable.
NOTE: The RovoCam camera ships configured for 1080p59.94.
5. Power up the HDMI monitor. You should see the camera image on the
monitor. This conrms the camera and links are working.
6. Connect a control source to the RS-232 input connector, using a 3.5mm TRS
cable.
7. Install and congure RovoControl (or a third-party control application) for
operation with the RovoCam system.

RovoRx UltraHD HDBaseT Receiver v1.0r1 11 www.aja.com
Audio Level
The RovoCam microphone input is a single ended stereo audio input with a fixed
20dB of gain. The RovoRx has a fixed audio gain of 10dB, giving a system gain of
30dB which will bring a typical microphone output up to line level.
System Ground and Audio
When the RovoCam is used with RovoRx, the power provided by RovoRx
has 1500V isolation from ground, meaning that the RovoCam is electrically
isolated from ground. When RovoCam is used with an external microphone, the
microphone is also isolated from ground, and there will be no noise issues. If you
use the RovoCam microphone input from source equipment which is grounded it
can cause ground loops in the system and unintended noise will be heard on the
microphone input. To correct this, the user can ground the RovoCam camera by
connecting a ground wire to the negative input of the 12V DC power connection.
This will effectively tie the camera to earth ground and eliminate the unwanted
noise.
RovoRx-HDMI Rack Mounting
The RovoRx-HDMI can be mounted to a rack using AJA's optional RMB bracket.
The threaded holes in the case can also be used for mounting without the
bracket, using 1/4 inch 440 thread screws.
RovoRx-HDMI units can also be installed in AJA's DRM frame, but each RovoRx-
HDMI will require its own external power supply (provided). If unused space is
not available in the DRM frame, the power supplies can be tie-wrapped above or
below the frame, provided air flow is not restricted.

RovoRx UltraHD HDBaseT Receiver v1.0r1 12 www.aja.com
Chapter 3 – RovoRx-SDI and Mini-Config
RovoRx-SDI Overview
RovoRX-SDI converts uncompressed HDMI Video/Audio signals up to UltraHD
for reception via HDBaseT over CAT type twisted pair cable. It includes a frame
sync function, designed specifically to lock the RovoCam signal to a facility
reference for use in a production facility. RovoRX-SDI is designed to pair with
the AJA RovoCam camera, to provide video, audio, RS-232 control and power
transmission using a single CAT cable. Video and audio can be received by this
device over distances up to 328 feet/ 100 meters on Cat 6a cable, to drive displays
or ingest into an SDI production environment. RovoRX-SDI can also be used with
any compatible HDBaseT transmitter, including AJA’s HB-T-HDMI and HB-T-SDI
Mini-Converters. See "Appendix A Specifications" on page 27 for a complete list of
supported formats, frame rates, and CAT cable requirements.
NOTE: The RovoRx-SDI packs an unprecedented feature set into a Mini-Converter box.
As a result, the unit uses approximately 14.5 watts of power. It will be very warm
to the touch, which is normal. The unit is engineered to operate across the full
temperature range, from 0 to 40 degrees C.
RovoRx-SDI Features
• Integrated Framesync with genlock to external reference
• 4x 6G/3G-SDI BNC outputs
• 1x HDMI (UltraHD capable) output
• 6G-SDI output of UltraHD
• Loop through Reference BNCs
• DA Mode for distributing multiple SDI signals from an HDBaseT source
• Extend uncompressed UltraHD or HD HDMI signal up to 100m over CAT cable
• RS-232 control on the same RJ-45 cable
• Two channel unbalanced analog audio outputs, when used with RovoCam
and optional stereo microphone
• Mini-Cong support for control and status
• 48VDC power supply (included)
• Optional RS232 Cable Kit (HB-CABLE-KIT)
• 5-year warranty

RovoRx UltraHD HDBaseT Receiver v1.0r1 13 www.aja.com
RovoRx-SDI Block Diagram
RJ-45
HDBaseT In
RS-232 Out
Power Out
+48 VDC HDMI Output
USB Cong
Port
RS-232 In
Left Audio Out
Unbalanced RCA
Right Audio Out
Unbalanced RCA
USB HDBaseT
Port
RS-232
Receiver
Power
Distribution
USB Cong
Control
HDBaseT
Receiver
Framesync
and Video
Processing
+10dB
SDI Out 3
SDI Out 4
REF Out
REF In
SDI Out 1
SDI Out 2
(Future Use)
Video
Video
(no embedded audio)
Video with up to
2 Ch. embedded audio
Active BNC
output connectors
depends on
format and
conguration
Audio
Analog Audio
from RovoCam
RovoRx-SDI I/O Connections
LINK LED
HDMI Output
Connector
3.5mm TRS
RS-232 Port
HDBaseT
Input
Connector
DC Power
Input
Right Analog
Audio RCA Output
Left Analog Audio
RCA Output
LOCK LED
Power LED
SDI Output
BNCs 1-4
(Future Use)
USB Cong
Port
Reference
Input BNC
Reference
Output BNC
NOTE: The LINK LED, when green, indicates an active HDBaseT connection.
NOTE: The LOCK LED, when blinking green, indicates a lock to a valid video source.

RovoRx UltraHD HDBaseT Receiver v1.0r1 14 www.aja.com
System Installation
NOTE: For highest reliability, the Mini-Converter relies on convection cooling instead
of using a built-in fan. Therefore, when installing the unit, mount in a location
where it has access to air for proper cooling. Do not stack the RovoRx-SDI with
other Mini-Converters.
RovoRx-SDI Installation with RovoCam
Typically, installation consists of the following steps:
1. Ensure the RovoRx-SDI converter is disconnected from power.
2. Connect the RovoCam HDBaseT RJ-45 output to the HDBaseT RJ-45 input
connector with an approved CAT cable type and length.
3. Connect the RovoRx-SDI HDMI output to the HDMI input of a destination
device (in this example, an HDMI monitor) with an HDMI cable.
4. Connect the RovoRx-SDI BNC outputs to the SDI inputs of a destination
device. Begin with the SDI 1 connector.
5. Connect the 48 VDC power connector to the RovoRx-SDI, and then connect
the provided DC power supply to an AC power source with the supplied
cable.
NOTE: The RovoCam camera ships configured for 1080p59.94 video format.
6. Power up the HDMI monitor. You should see the camera image on the
monitor. This conrms the camera and links are working.
7. Connect a control source to the RS-232 input connector, using a 3.5mm TRS
cable.
8. Install and congure RovoControl (or a third-party control application) for
operation with the RovoCam system.
9. For advanced features (for example, DA output) and specic SDI output
conguration, download and install AJA’s Mini-Cong application onto a PC
or Mac (see "USB Control and Setup—Using AJA Mini-Cong" on page 15)
Audio Level
The RovoCam microphone input is a single ended stereo audio input with a fixed
20dB of gain. The RovoRx has a fixed audio gain of 10dB, giving a system gain of
30dB which will bring a typical microphone output up to line level.
System Ground and Audio
When the RovoCam is used with RovoRx, the power provided by RovoRx
has 1500V isolation from ground, meaning that the RovoCam is electrically
isolated from ground. When RovoCam is used with an external microphone, the
microphone is also isolated from ground, and there will be no noise issues. If you
use the RovoCam microphone input from source equipment which is grounded it
can cause ground loops in the system and unintended noise will be heard on the
microphone input. To correct this, the user can ground the RovoCam camera by
connecting a ground wire to the negative input of the 12V DC power connection.
This will effectively tie the camera to earth ground and eliminate the unwanted
noise.

RovoRx UltraHD HDBaseT Receiver v1.0r1 15 www.aja.com
RovoRx-SDI Rack Mounting
The RovoRx-SDI is too large to be mounted into AJA's DRM frame, and the
location of the unit's threaded holes are incompatible with AJA's RMB bracket.
The threaded holes in the case of the RovoRx-SDI can be used for mounting,
using 1/4 inch 440 thread screws. However each RovoRx-SDI runs at about 18
watts, so air movement will be required wherever it is installed. The separate
RovoRx-SDI power suppliy can be tie-wrapped to the rack frame, provided air
flow is not restricted.
Figure 4 shows an example of mounting multiple RovoRx-SDI unit into a rack
frame that ensures adequate cooling.
Figure 4. RovoRx-SDI Rack Mounting Example
USB Control and Setup—Using AJA Mini-Config
Your AJA Mini-Converter can be used right out of the box for some applications
since it is designed to recognize inputs and perform standard actions
automatically by default. However, to use its full capability, you must use AJA’s
Mini-Config software application for PCs and Macs. This same application can be
used to update to new Mini-Converter software released by AJA.
Acquiring AJA Mini-Config
AJA’s Mini-Config application is available for download from the AJA website.

RovoRx UltraHD HDBaseT Receiver v1.0r1 16 www.aja.com
To download the latest AJA Mini-Config package, which includes the AJA Mini-
Config application, Mini-Converter firmware, and documentation, go to:
https://www.aja.com/en/products/mini-converters/mini-config-software
Select either the Windows or Mac icon to download the desired version.
Mini-Converter Documentation
Included with the AJA Mini-Config package is a complete set of documentation
for all Mini-Converters supported by AJA Mini-Config. A .PDF of the Installation
and Operation Guide for the currently connected Mini-Converter can be accessed
from the AJA Mini-Config UI via the Help/Manual drop-down menu.
Documentation for all AJA Mini-Converters that use AJA Mini-Config can also
be accessed directly in the AJA Mini-Config download package Documentation
folder, and via the Documentation icon available on the Mac installer.
Documentation (and firmware) included with the AJA Mini-Config application
are the versions available at the time of distribution. However, Mini-Converter
software, firmware and documentation are updated regularly, so newer versions
may exist.
To download the latest documentation for an individual Mini-Converter, go to:
https://www.aja.com/en/category/mini-converters
and navigate to the Support webpage of that Mini-Converter.
Installing AJA Mini-Config
PC Installation
To install AJA Mini-Config on a Windows PC:
1. Download the application from the AJA website (select the Windows icon
on the AJA Mini-Cong Support webpage).
2. Open the AJA_MiniCong.zip le
3. Double-click on the MiniInstaller.msi le.
4. A Setup Wizard will guide you through the installation.
Figure 5. AJA Mini-Config PC Setup Wizard
5. Click Next to begin. Answer the questions in the subsequent dialogues.
When nished, an AJA Mini-Cong shortcut will be installed on the desktop,

RovoRx UltraHD HDBaseT Receiver v1.0r1 17 www.aja.com
and you will be able to locate the AJA Mini-Cong application in the AJA
folder in the Programs listing.
NOTE: If the AJA Mini-Config application already exists on the PC, a different Setup
Wizard appears.
Figure 6. AJA Mini-Config Setup Wizard, Reinstallation
With this screen you can Repair (reinstall) or Remove (uninstall) AJA Mini-Config
on the PC.
Mac Installation
To install the application on a Mac:
NOTE: Macintosh computers must be Intel-based (G5, G4 and earlier models will not
work with AJA Mini-Config).
1. Download the application from the AJA website (select the Apple icon on
the AJA Mini-Cong Support webpage).
2. Open the AJA_MiniCong folder.
3. Double-click on the AJAMiniCong.dmg le.
4. Answer the prompt and a utility program will be launched.
Figure 7. AJA Mini-Config Mac Installer
5. To complete the installation drag the “MiniCong.app” icon to the
Applications folder.

RovoRx UltraHD HDBaseT Receiver v1.0r1 18 www.aja.com
Running AJA Mini-Config
Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect
the external power supply (supplied) to the Mini-Converter.
PC Startup
To run AJA Mini-Config on a PC, double-click on the AJA Mini-Config icon on your
desktop, or open the AJA folder in the program list and click on the AJA Mini-
Config application located inside the AJA Mini-Config folder.
Mac Startup
To run AJA Mini-Config on a Mac, open the Applications folder and locate the AJA
Mini-Config application. Double-click the application to launch it.
Saving Setups
A File drop down menu on the AJA Mini-Config application bar allows you to
save the current state of the Mini-Converter to a preset file for later recall.
Using this feature you can set up the converter for different applications, storing
each configuration (Save Preset As...) with a unique name for easy recall (Open
Preset...).
A Revert to Factory Settings menu item similarly allows you to change the
settings back to AJA’s factory defaults.
Operating AJA Mini-Config
The AJA Mini-Config application provides a graphic interface for viewing settings
and updating software. It consists of an information area at the top that shows
the available Mini-Converters attached to the computer via USB, with a graphical

RovoRx UltraHD HDBaseT Receiver v1.0r1 19 www.aja.com
rendering of the selected Mini-Converter showing all the connectors and their
current state.
Colored text next to the connectors indicates the signal type and what the Mini-
Converter is doing:
• Blue text indicates the values automatically selected
• Black text indicates values that you have manually selected
• Red text indicates the Mini-Converter is not detecting a signal, or cannot
operate with the current user settings.
NOTE: Even if no output device is detected, the SDI connector text still shows the signal it
is outputting.
NOTE: Configuration settings in red will change based on the attached output device as
well as input signals. For improved accuracy and reliability, you should configure
the Mini-Converter only when the target output device is attached and input
signals are supplied at the inputs.
Screens are virtually the same on both PC and Mac, with subtle differences that
reflect the general look of the platform environment.
Running Multiple Mini-Converters
AJA Mini-Config can manage multiple AJA Mini-Converters connected via USB—
even when they are of differing types. However it only connects to one at a time.
You can choose which Mini-Converter you wish to control using the pulldown
menu in the upper right hand corner. If you want to configure multiple Mini-
Converters in parallel, you can do it by running multiple instances of the AJA
Mini-Config application and have each control a different Mini-Converter.
NOTE: During a Mini-Converter firmware update, only one Mini-Converter should be
connected to the computer via USB.
Figure 8. Example AJA Mini-Config Screen
Firmware Version
and Serial Number
Select a USB port and an
attached Mini-Converter
(name in parentheses).
Each connector is
labeled with the signals
currently detected or
manually selected.
Tabbed Screens
Message Showing
Status

RovoRx UltraHD HDBaseT Receiver v1.0r1 20 www.aja.com
Firmware Version
and Serial Number
Select a USB port and an
attached Mini-Converter
(name in parentheses).
Each connector is
labeled with the signals
currently detected or
manually selected.
Tabbed Screens
Message Showing
Status
NOTE: The LINK LED, when green, indicates an active HDBaseT connection.
NOTE: The LOCK LED, when blinking green, indicates a lock to a valid video source.
Selecting a Mini-Converter with the pulldown menu causes this application to
connect to the selected converter. The graphic of Mini-Converter and text below
it provides:
• Type of converter
• Firmware version
• Serial number of the unit.
A status field at the bottom of the screen shows if your application is connected
and communicating with the Mini-Converter.
When configuring the Mini-Converter, select it from the top pulldown, view the
current settings and change any values. Making a change communicates that
new value to the Mini-Converter’s non-volatile memory.
Tabbed Screens
The Tabs delineate control screens with groups of controls for each type of task to
be performed. The controls for the actual configuration parameters are specific
to each Mini-Converter type. When you Click on any of the tab buttons, the pane
below the tabs will change to match your tab selection. Any changes you make
are immediately applied and will be saved, overwriting previous settings.