Akicon 96118 User manual

IMPORTANT NOTICES: For easy installation, please read all the instruction completely before beginning.
Before installing this product, make sure that water line trash is cleared to avoid blockage.
YOU MAY NEED
After you open this package, please check to ensure that all of the following items are included.
A- Faucet B- Flexible Hoses(2) C-Plastic Support
D-Mounting Nut + Washer F-Allen Wrench
Kitchen F(Bar) aucet
1
E
EX: E001007T Rev: A
4
CAUTION: Maintenance
1. Replacement parts may be available at the store where you purchased your faucet.
2. Always turn off water and relieve pressure before working on your faucet.
Turn off water and relieve pressure! Detach handle button
using a small flathead screwdriver, unscrew set screw
using Allen Wrench and take off handle.
Remove handles. Unscrew Dome Cap counter clockwise
by hand. Unscrew Retaining Nut using adjustable wrench,
take out cartridge assembly and inspect. Replace parts
as necessary. Reassemble parts by reversing steps.
Handle Removal Maintenance Valve Cartridge Removal Maintenance
PACKING LIST
TROUBLE-SHOOTING
If you've followed the instruction carefully and your faucet still does not work properly, take these corrective steps.
Problem Cause Action
Leaks underneath handle. Cartridge has come loose. Tighten the cartridge.
Aerator leaks or has an
inconsisitent water flow
pattern.
Aerator is dirty or worn
out or misfitted.
Unscrew the aerator to
clean or replace washer,
or replace the aerator.
Water will not shut off
completely.
Dirty or worn out washer
in cartridge.
Remove handle and cartridge
to check if the washer is damaged
permanently or dirty. Re-install
cartridge.
NOTES: Cleaning Instructions
1. To keep the faucet clean, you should clean the faucet frequently and regularly.
2. Clean the faucet with clear water or mild liquid, rinse the faucet with clear water and then
dry the faucet with soft cotton cloths.
3. Do not use any abrasive cleansers, cloths, or paper towel.
4. Do not use any acid or abrasive detergent.
B
A
C
Optional accessories
D
Questions, problems, missing parts?
call Akicon Customer Service 8 a.m.-6p.m. EST, Monday-Friday
Phone: [phone], Email: [email protected]
AKICONSHOP.COM
Model: 96118
96118P1

3
Swing Spout
5
6
INSTALLATION PROCEDURES
Remove anydebris from valve outlets.
Turning off the water supply valves. This is usually
found near the water meter. If you are replacing
an existing faucet, remove the faucet from the
sink and clean the sink surface thoroughly.
Install without Deck Plate. Make sure the O-RING
is placed onto the bottom of Base Ring. Install
faucet through hole in sink. From underside sink,
attach mounting assembly Position
faucet on sink properly and tighten Mounting Nut.
If necessary, tighten screws using a adjustable
wrench until the faucet is firmly connected to the
sink.
Connect hot and cold water supply lines to the
Hot
Cold
Water
Supply Valves.
2
1
2A
3
4
Close
Open
After installation is complete, remove aerator and rotate
handle to the closed position. Turn on the water supply
valves, and check all connections for a leak. Turn on
your faucet and allow both hot and cold water to run at
least one minute each. Replace Aerator.
Faucet Start Up
2B
Install with deck plate. Place a bead of plumber's putty
between faucet and sink. Place deck plate over the three
holes of sink.
Make sure the washer is placed onto the bottom of base ring.
Install faucet through deck plate. From underside sink, put
plastic washer and mounting nut. Position faucet on sink
properly and tighten mounting nut.
Open the valve, then turn the handle according to the
sign of C and H on the handle to regulate the temperature
of the water. (C=Cold,H=Hot)